Video

its been a few years, and im sure youve improved a lot, but i would probably use a 5 inch box and try to use a GFCI somewhere, whether you have it inline on one of your powercon cables, or a GFCI receptacle. if you use a receptacle though, make sure its rated for outdoor use, just in case you get caught in the rain, you dont have the potential to hurt anyone, and when its outdoor rated, it wont trip as soon as a drop of water hits it. theres also raised cover plates you can get, but theyre designed for use in walls, so youll have to get a little creative, but even just 5/8s of an inch will get you a lot more room to work with without adding much more space. there are also electrical boxes that have larger knockouts than 1/2 inch and 3/4 inch. im not sure if those boxes come in stamped or are just welded though

I’ve got a noob question that possibly doesn’t make sense… since you’re daisy chaining these, would it be possible to wire them for two circuits? Somehow go from two male Edisons to powercon? That way you could power the whole chain with two circuits and have some extra juice if needed?

Can a speaker control a light as dmx ?

If you don't have fly points and the top of your speakers are fairly flat you can use strong outdoor use velcro strips (15lb+ hold). Trim them to size and they are very secure. Only thing is there isn't adjustments up and down like it is here when you attach using a fly point on the bracket.

Brilliant

Does work well if you connect it directly thru the dj console?

nice man! if u wanna sell that old solution, id take it ;) or how can i get that small pole for the light? you were cutting an old long stand right? Also, where is that "previous video" u mention? thanks :)

I see u have the 4 channels on serato can u use all for channels on the controller ? Nevermind just saw on your video that u can how do I make set up my serato to be able to use all 4 channels 🙏

This is a great idea! Thanks for sharing. I'm trying to figure out how to do the same thing with my JBL PRX-715's.

You mentioned the tent situation where you have to share a breaker with the lighting, kitchen staff etc. You then said that you had a solution and went into how to use a wirelss mic to make a wireless speaker? But if its a powered speaker youd still need to get power to it and that doesnt address the sharing of a breaker. Was hoping you had some amaxing solution but i didnt hear it

Joe, I don’t like trusses or totems either. My speaker has two M8 threaded holes that I can mount lights too. I would like to do this. I would like one light on top of each speaker. My question to you, what two lights would you recommend? I’m fading away from weddings. I primarily do karaoke and private parties. Please help! Paul

Its decrease de voice sound quality?

What did you use to mount the antennas?

Just ordered! Thanks for a great tip!

Great video! Quick question..Does mounting a dj light to the top of speaker ever burn out from vibration?

The only thing I would change in your kit (or add to it) is a passive stereo DI, not just mono; for balancing and unbalancing stereo signals.

Your prepared for Armageddon great 👍

What did you use to achieve the starry projection Joe?

Can you show exactly how the mics and prime go are plugged into the go rack and then out to main? I see you coming out mono on the prime go but mics go into go rack and then where do they go? Thanks

NICE JOB MEN !!

avoid doing this, speakers arent meant for mounting stuff. It starts looking like a 3rd world dj system

really cool video, but quick question...Why mess around with the yoke and mount when you could have just bought an m10 bolt or wing nut and threaded that directly through the light bracket to the top of the speaker?

is the lights right in or at eye level ?

great setup, and custom cables

Very nice setup. Lots of DJ.s can learn from you. I worked at a country club. Wow the stuff i havw seen scary. They always ask for batteries cable and extention cord and duck tape. Some guys call themselves DJ’s

Good morning Joe, I hope you are doing well, at the moment that I'm writing this it's been 5 years since you posted this video. Would you be able to tell me where to find the BNC bracket you used at the rear of the mixer case? Thank you.

I am curious about the next steps, how do you connect the lights, the power cord is 6 ft, Do you use power extension ? Do you use DMX cable ?

I would like to share with u on what I made but I can’t seem to be abLe to send u pics. Message me then I can.

Just make it work, Best way to put it. Be the hero

How do feel about an M10 x 40mm Hand Bolt straight through the hole on the lighting fixture into the fly point?

Nice rig

Appreciate you taking the time to share this. 👊🏼

Do you make and sell those items? If so? How much would you charge me to make me a couple of them?

I just bought a couple of M10 Bolts with a wing on top. It's cheaper and does the same thing.

The dj is at the bottom of the barrel. No one makes less money and puts in More work than us. I dont show up to an event thinking of anyone other than myself. Videographer, photographer, they all make more money than the dj. Why should i pend my money on stuff i dont need just incase i need to bail out a unprepared soul.

What's the benefit of using the PowerCom connector instead of just wiring the cable to the box?

very good job and looks very clean

Wow - really slick!!!!!

Could you just get a stud that has 5/8 to 3/8 then just washer and nut the side to the light?

Great video. Thank you for the info!

Love it bro

Garvin makes boxes with no holes. looks real neat.

Do you always have time in between cocktail hour and the ceremony to break down the cocktail rig?

you are like a mad-scientist! thx for bringing my/our-shared theory to life. ive been a Cali DJ since the mid-80s - began making cable this year. #djpleez

Awesome set-up. Also very informative.

Awesome,... Saved me $$$ and Great Idea...

Hi Joe, great videos thanks, how did the eon one pro work out for you? I have seen many scare stories on the #JBL eon one pro specifically, and a complete lack of support from JBL, hence they brought out a mk2 recently.

Outstanding!!!!!!

you need some Milwaukee Packout

Cool setup. Thanks for sharing can you post the parts please ?