Video

Have you tuned to E-85 yet? I'm curious to know what numbers you'll anticipate with the same setup.

Fercho

Oil grade for 4g63t what you suggest

Nice man that worked out well.

How much torque ,psi ,and power can those headstuds can handle ?

07 Mustang looks better but drives worse huh funny

Did you hook the fan to a switch in the cab?

is 2006 eclipse with 166k miles still reliable? someone selling it for 3.5k

Redondo!!!! Tá brutal já!!!

Thanks for the video.

120nm toq

Sir it means evo8 valve spring is thicker than dsm valve spring? How many rpm das the dsm have.and evo 8 valve spring.hope you answer my question.thank you souch.

Just subscribed

i would gap both of these with my 3g eclipse lol

Geeze tha baby sounds a very nice 👌

Really helpful! Subbed!

Very helpful man. About to tackle this soon. Thanks for the video.

Good info.. nice video also

PLEASE, WHO EVER READ MY COMMENT: DO NOT MAKE THIS STUPIDITY. DON'T MAKE MY MISTAKE.

Yooo I’m so excited for my eclipse

Will it break off over time when the mounts flex?

So, what happened? Did you use them or not? You never came back with result. I just did this but the tube only last for rear and front motor mount. Half of the Transmission mount. Other people say it fit 4 motor mount which is a lie.

Nice and meaty 🥩

Back in the day we would do whatever to rig up something to spin the pump. Then i learned the easy way when i worked in a shop. Pressurized container filled with oil and plumbed into a sender port and it has a connection for shop air to pressurize it. I took it a step further at home and got a new bug sprayer and rigged a line on it. Oh i added a hole for a tire valve,so you can check the pressure. The hand pump on those will give you 50psi easy. Ive used it 3-4 times so far and its alot easier and you dont have to rush to reassemble anything, id shut off the valve i installed and hit the key.

Dude, I was just searching on how to do this today. Thank you 😊

Good info

👍

Nice just bought it was considering these 2. I guess it was a good choice.

What did you do to clean the rubber part of the mount?

Man that’s awesome. I have an 03 ram with the 3.7 v6. I’m in the process of converting it to electric fan. I’m using a 2007 Chrysler 300 electric fan. I hope it works. Everything is ready to go, I’m just trying to figure out how I’m going to mount the washer fluid and coolant tank. Awesome setup!

Can I do a balance shaft delete without pulling the whole engine?

Have you used them yet? Does this cause any vibrations or rattling inside the car or is it still like oem?

That stang is a v6 😂not a v8

Is it the same for 2g?

I have a 4g63t I bought... previous owner said tensioner broke on start up... I pulled plugs and scope said valves hit. I am thinking I might try to machine head and reinstall... what do you think if everything else checks out. I have 16 cars and it gets tough to rebuild and make everyone perfect

i walk em down with my 4 cylinder dem infinitis be takin dem boyz onna jump easily nd onna rolls

Why u jumping ?

What led did you buy to replace these?

Can you use this head with an evo 8 stock turbo frame? How would you run the coolant lines to the turbo?

What fan are you using ? From what car

Damn, didn't learn your lesson the first two times?!..😅😅😅

Love that Mitsubishi service department sign!! Hang it up!! Lol

What’s that fan off of ?

Was it hard to install?

and he smoked his itch bass with his window down 😂

I would still fill that old bad mount up with the polyurethane anyways and paint it just to have it on standby

I just picked this up today, when I compress the spring the valve pushes out so I can’t remove the keepers, how did you keep your valves from moving?

good vid. you can't beat an OEM pump housing tho. I would not gamble a fresh forged bottom end on ACL or any aftermarket pump. IF you can afford OEM you SHOULD get OEM

My 2010 GT Eclipse is a great ride, even going on 13 years.