Video

To much talking

Take the splash guard off ffs...this is crazy, I'm out

also the reason that slip was hard to get back on the spline is because there is a flat spot/key way so that yoke can only go back on the spline 1 way. you got if out of phase, as well as on the wrong spline

caps are same just the body of the joint is different

wasn't the right u joint lol. you got a 1350 instead of a 1410

Omg thank you so much it took me a week to find this video

That fuel line is pressurized

Love the shirt! I only have 2 weeks worth of them.

According to the owners manual you should fill the pumpkin to just below the fill hole. If it's running out, that's too much apparently.

Now I will give you a tip your saw goes to the same number on both sides there's a button that moves that brace to the side for a bigger saw 😂

Hay Tom! whats your ideas on the pump cutting out and sputtering?

Thanks! I've never seen a dryer door flip be so complicated. I'm glad I found your instructions. Super helpful.

it might be dumb to others but for me i needed to learn this. Just wished you would have showed how to actually make the cut using a square that i just bout today.

All this time wasted you should change that pressure tank out to a traditional diaphragm pressure tank. And if you still have the issue then you know it's within the well itself. Possibly a broken well line sucking air.

Burner is now 20 bucks, welcome to 2024

To much bs

To much bs video before getting to the point

I thought this could be the problem but absolutely nothing happens when I turn the key.

Great video Thank you 🙏🏾

That white smoke is creosote from the dirty smoker

Good video showing the basic process. My only advice would be to not go rounding corners that the owners had staked themselves as square. They may have had reasons for wanting a square corner, so it's probably best to check with them before modifying their design, unless of course they'd already disclosed to you it was ok for you to take design liberties. Also, just casually speaking, the reason they may have wanted the pond further on top of the hill than your recommendation, is because hill top ponds will usually remain cleaner than retention ponds situated downhill, as the latter type will fill with sediment and debris after heavy rains. I appreciate the upload and may peruse your video library for more similar content. Take care!

Thank you for posting this demonstration. Do you know if this pump could be used to flush and pump an RV black tank 100' to a house sewage clear out?

Hey tom, do you have a manual for this tractor? can't find anything online

Good info. Kids pretty loud

How did they do?

Reverse sear! Smoke first then sear it. If you sear first you block the smoke from penetrating in.

Spider headlight bulbs SUCK!!! Took them off and sold them after a week SYDER HEADLIGHT ARE GARBAGE

I have this exact pressure canner. Amazon sells seals that fit!

Every once in a while there a video solving a fairly simple problem. A simple problem that is causing lots of strife in many people’s lives. Thank you for taking the time to press record 🤙🏻

You say there are 4 screws to mount it back up, but it looks like there are only 3 screws?

about to go take the permit test tomorrow they trying to tell me all these busses have "hydraulic brakes" but the guy legit just showed us a Air break test the other day and he said when the DMV question comes up what kind of breaks are these I said Air he said no these busses are hydraulic brakes, then we argued and he told me just hydraulic brakes he had no answer for my questions where are the The break fluid reservoir, he couldn't show me.

You still have your century tractor

How is it pushing the rubber boot up into the bottom of washer to bolt it in. Anything I should know ? Does it seat in there ok and not leak? I'm getting ready to replace mine.

My breath blows water out after it blows air out.. what do y’all think

Help me! Thank you

Excellent video, thanks for all the "information" lol.

The old regulator had a plastic thread, the new one has a steel bolt in the center. You can replace the whole regulator part (AB-9051116) or just the red knob and valve.

i use my tiller 1-2 times a year 30min top Breaking-in the engine for such a small use seems unnecessary~!

East Texas is home ❤

echo the others here - I was going to buy and replace my water inlet valve until I saw your video. Then I figured I should check the overflow switch. It seemed up, just like you mentioned, I pushed it a few times and presto - dishwasher working again. I did not have any foam there. I think in my case someone pulling out the lower rack (or putting it back) bumped the overflow float and that jammed the switch underneath.

It’s probably the resister.

Shop vac next time.

Helpful video but the lack of prep and cleaning that was done is hard to watch. Please buy a flashlight. They aren't really expensive.

Ok

OMG... You are a life saver. I was struggling with my 2 inch PVC. I cut myself, hands went numb and still couldn't push that thing through. I used a bench grinder with a wire wheel at the edge, followed with some sand paper. A little Olive oil and it slid in without effort. Thanks a million.

How about getting someone whos not scared of them to come relocate them?

Hey Tom first off great video. We do big ponds and sometimes those slopes are a bit high with us but for the most part with new pumps they push through. However we have about 8 of these pumps that all turn on and some may pump a bit and stop pumping. We have tried opening them checking them all out and replacing the seals and gaskets with no luck. I’m not sure as to why the heck we have 8 pumps none of which help us pump water out anymore!

❤ thank you

Listen to me honey!!! I thank you so much! Like literally just did this..and…Booom!!! 🙌🏾🙏🏾 Edit to add.. Can you do one for a microwave that keep blowing a fuse? Same brand. 😢

Well, some genius didn't know how to install an inline filter because it was backwards. Also you put it on backwards. The fuel comes in on the outside of the pleats, goes through it to the inside. Most have arrows but most people that do that stuff regularly or for a living don't even have to think about it lol