Video

Thanks!

Hello Sir Can You Show Me How To Replace Passenger knee airbag on the mustang gt 17?

looking to reset my module on 2021 dodge charger

Will q50 start if airbags go off

Very good sar

Hello friend, can you tell me if the Ford Edge has the same sensor or not?

This was a helpful video. Just make sure that removing the (shifter control) panel to start in the front by lifting up and then slide the panel forward to release it.

How do you reset it ? Or do you have to replace it ? I called the dealer and wants to charge me 670 dollars for a new one and charge me 170 dollars to reprogram it to the car.

Helped a lot thank you

4:49 Hi. Question. In your vehicle was the fix to replace the sensor with a used one or did u pull the head off of the old sensor and add the head from another sensor after you pushed the red pin back into place? Please clarify as your pics looks like u did that. Thanks please clarify how u fixed the sensor

2 screws on each side console lifts up u can remove from the back took me 15min didn't touch nothing what u said😂

Thank you, I just need to replace the curtain airbag and be done with it.

Promo'SM 🤪

Super helpful and efficient, thanks.

Thanks for your detailed video

Dude you should make the video 2 minute longer but don’t skip. I literary was unscrewing everything till I realized the 2 screws under the plastic cover. It would save me two hours

يعني صار كم مرة اكولك ساعدني منين اشتري الطلقات مال الاحزمه ومجاوب ترى اني مو جيرانك حتى انافسك بشغلك

Thank you

Hello, I'm working on a 2018 VW Atlas. Question, I have a B189CF0 "Crash Shut-Off, Active code. When I removed the Airbag Module, I Still Have that code, and U015100 "Lost Communication With Airbag Control Module". These codes are located in the Diagnositic Data Interface-Gateway. However the only codes scanned that were located in the Airbag Module location, were for the Pass. and Driver Belts, as they should, due to the Belts being deployed from the impact. From prior VW's The so called "Crash Data/Crash Shut-off data was located in the Airbag Module. Will having the Airbag Module serviced, remove this "Crash Shut off, Active Code in the Diagnositic Data Interface-Gateway. In other words the gateway can not be be fully cleared, untill it sees some kinda reset info from the Airbag module, or is this some type of dealer only procedure to remove this Crash Code. Best Regards...and thank you for any info you are able to provide.

من وين تشتري مواد تصليح الاحزمه ؟؟؟

Awesome job

Thank you for this! PITA to remove.

Hi dear, In this case, if you find another Airbag Module (Same Part Number) from other car WITHOUT crash. It can replace the original Airbag Module directly? or is necessary program the new Airbag Module with data of VIN chasis ECU BCM information? please your comments. Thank you.

Do you have a video on how to remove the usb port?

؟؟؟؟؟؟؟

شلون الصحة سالتك قبل على دورة تدريب وجاوبتني متكدر اريد اطلب منك طلب وارجو ان تساعدني ممكن تكولي منين اشتري القطعة الي تتبدل بلحزام لان حاولت الكيها بلايبي ومالكيتها واصيرلك ممنون

You skipped so many steps at the end how do you actually lift the back up to gain access? Mine is still tight at the back

my car is 2017, got accident and same sensor is showing. but also my steering wont lockup after accident. I am assuming its the same sensor causing this thing?

Dumb video did not help. Missing a lot of steps

مرحبا ممكن طريقة للتواصل مع حضرتك 😊

BAD TOOL DO NOT BUY IT.

I will list a video about this issue tomorrow

Go to Occupant Classification System OCS on your diagnosis Scanner device and delete the DTC.. it should fix the problem

There is any way you could give me an advise how to i can fix code B00A0:68 2018 ford explorer can’t find the problem thank you

Man you just save my life thank you for your videos