Video

Whaaaaaaat! Harley-Davidson recommends using there branded oil filter!

We use supertech in all our bikes here. We have a wideglide 2 sportsters 1200 and 883 and a 1986 honda rebel 450. We use 20 50 in the Harleys and 10 40 in the honda everything shifts smooth and runs great. I was apprehensive at first but am now a convert. I'm also using supertech in all our vehicle's now with no I'll effect. In my opinion the honda seems to shift smother now than before . When doing oil changes I see no more on the oil plug magnets than when we used higher priced brands. Also the oil really seems no worse than the name brands when draining either. In my humble opinion it appears to be a good product at a decent price.

So basicaly 2.2 oz of mix to 1 gallon of gas for 50:1?..

just fixed my A/C Thanks!!!!

Short,sweet and to the point...no BS ....thanks

How did you remove the plastic shroud that's mounted on top of the flywheel? Has some weird style clips holding it on place

If you have a container, diesel may be cheaper, plus works in many torpedo style heaters.

Best explanation of crankcase ventilation/check valve. Thank you

At first i thought it was the wires under the dash on the passenger side, when i last tackled this issue. Turns put on this vehicle its different and this issue you presented looks to be it!

I checked fuel flow rate before by connecting separate fuel source to Ron the engine with variable pressure electric fuel pump. For example, 2 gal pet hour would be 16oz (2c.) in 3 min., 45 sec. Let the engine run off other fuel source, pumping fuel into a measured container. Don't forget to start your timer when the engine fires up, and SECURE THOSE FUEL LINES!

Excellent video. I wouldn't have attempted this before seeing your video but your instructions are great.

That old hose that connected to the vacuum tank, where did the other end of that hose connect to?

note for future viewers. most first time brake fluid changers don't know this, but if you pump the hand pump too much you can accidentally suck brake fluid into the hand pump itself and on the cheaper models brake fluid will ooze out of the seals in the hand pump and make an awful mess.

This is exactly what I was looking for. Thanks.

I gave it a thumbs down cause you showed the easy side

👍👍👍

Nice work sir

If anyone is doing this as an addition to removing governor (good choice) know that this is enough and that if you leave the stock springs you will not need a billet rod.

Any chance you could tell me the pin wiring schema of the adapter? I have the plugs and want to assemble the adapter..

I wonder if the motor regulator is getting weak and soon down the road it stops again. My truck 2015 F150 rear passenger window clicks when I push the drivers button and the rear button but no movement. At first it would work once in a while then completely stopped. Ironically it started right after the dealer pulled the door panel under recall to fix the weather stripping… of course it’s a window I don’t use often so it was months later when I found out.

Great job god bless

Going home

I don’t have one, but I know that you are very intelligent about your wiring and you fix it correctly.

Thoughts on the Sae 50

12 yrs later, it still helping people. ❤

Is this same for a 2006 model year fat boy?

I recently replaced all the vacuum lines and it started working, but then after about an hour or 2, everything turned off. I can't tell if the relay is bad or the fuse resistor blew on the blower motor? Any ideas? It seemed to work just fine and then randomly shut off? Fuse isnt blown, Going to replace the resistor & relay to see if thats our problem

👍👍👍

Wire brush is a safer option for cleaning the port

Nice work sir

Thank you sir 🫱🏿‍🫲🏻

I replaced all my vacuum hoses and it was working afterwards but now nothing is working on any setting. Any idea what it could be?

Thank you! Well done video. All others I could find did not explain it as thoroughly! I might be able to tackle this job now!

Mine does this also, but it’s on and off. Ac works when it wants to. Not sure what that could be

Thank you it was good information

What does the junction connect to ?? Myns was disconnected from the other end I don’t know where it goes ?

Ya they never come off that easy

Thank you for your help

I had a brain fart and forgot hoch way it goes. Thanks!

Tell us what socket sizes you are using to complete the repairs.

My switch OFF position reads 1.65 so my switch is bad ??

Wow

Great diagnosis sir. Thank you for sharing.

What could it be if I'm getting gas and oil in the carburetor it starts and then it starts smoking like a train any help is greatly appreciated!!!

Su cess!

Very informative and straightforward. Thank you for sharing this.

I did that same thing plus ran the other bigger hose which was split got air out dash,blower setting work fan speed works,but still doesn't blow out strong enough to keep cabin of 2013 GMC Savana,go from regular to max air it gets louder but to me don't blow hard enough doesn't change the power

Nice. Thanks for the tips. I did come up with a 3rd method; only because I watched this video after the fact. I setup my cellphone to record video in slow motion, started my mower and lifted the front wheels to record the spinning blade as I cut the engine. Lol.🍺😎👍🏻

Is that your vehicle? Thanks for sharing.

Nice Job!