Video

If I remember correctly, I say in this video that we didn’t tape off the whole counter because we replaced it right?

Haha if the jazz is preferred I can definitely leave it!

Love it, I’ve noticed we get less in the finish if we do that, did you end up trying it? How’d it turn out?

Thanks! I’m trying to get the actual video out now lol

Hi there! So for this particular door we did a 1-1, so one coat primer, one coat top coat (paint) depending on how it’s applied you might need more, or depending on your prep work it might need another coat to get the sheen even and not splotchy

Well thank you for watching it! If you’re spraying the products I’m using in this video I would encourage not going smaller than a 10 orifice size, so with this Graco quick shot I use a 210 tip, on our bigger rigs I prefer a 310 or 410. If we’re spraying thinner products (industrial grade) we use 206, 306, 308, 408.

Haha thank you! If I remember correctly when we did this video I would spray, run outside and take a breath before I’d come back in and spray more, perks of filming and my respirator not making it on site

Hey I appreciate that! We’ve been so busy running around we haven’t been doing Shorts but we start this week!

Anything is easy to paint by hand if you have enough time and don’t care about the finished product. Why would I use a high volume solid primer if I’m intentionally not flat sanding and don’t want to overfill the intentional embossed grain we bought the door for? We just wanted to increase adhesion, if we were going for flat we definitely would’ve went with a industrial coating but that defeats the whole purpose of these doors

@SupernalPaintingUSA it's not that high build when rolling or even spray to be honest just more solids to cover better

Hey Ben! The quick shot is great for small projects, we use it often for on site touchups post install of countertops, trim, etc. if you dial it in I think you can get a great finish on cabinets, especially Spraying horizontally, spraying vertically is definitely more tricky but it can be done I think

Hey Justin! We do. So for Industrial Grade Coatings we really like CIC Coatings 1108 and 1107 primers, their new Primer 1111 is a mix of both and is a great hybrid of both worlds I think

Hey Wade, I appreciate the comment. SW Gallery is a great Sherwin product, we use it weekly here, the AAA Kremlin is a fantastic gun too, we normally are running big airless rigs or AAA when we’re doing our large projects but I bust out the quick shot for small projects like this here. Do you know how many wet mils you put on the door with both sprayers? In my experience that’s what gets me when I would get orange peel

I sprayed Gallery again over the weekend and it laid down a lot better. I think because it was warmer that helped. Also, when I cleaned the gun afterwards, I think I saw some built up 2k material from a previous spray that was partially clogging a couple of holes behind the air cap. I’m pretty sure it’s going to work a lot better next time as I’ve never had the Kremlin lay down anything but glass. I look forward to more of your videos.

Love to hear it, it’s crazy how much even a couple degrees will change how material lays down. Make you feel like you’ve lost the touch at times haha. Do you personally enjoy more of the woodworking or painting/finishing videos?

I appreciate that so much man. That’s the goal of these videos

Hey there! I don’t understand all of the translation but it sounds like you’re saying we should hand sand instead of using our orbital sanders. I’m curious why you think we should do that if we need a surface to be flat so it can be primed and topcoated

That would be nice wouldn’t it haha. We’ve got several, miter station was just mid renovation during this video.

I love to hear that! Appreciate you watching the video

Haha I feel that sometimes, next time you paint them let me know how it goes!

they are so easy just roll 1 primer 1 top coat or 2 if its a color use a 3/8th nap mini roller

That’s great! What style of doors/drawer fronts are you doing? And what overlay are you thinking?

I will be doing Slab drawer fronts and slab doors, no hardware. I will back slope the top or the bottom of the door or drawer face, as a finger pull surface. We are shooting for a very modern clean look @@SupernalPaintingUSA

The overlays I will want very close fittings with adjacent drawer or doors, , , like 1/16

Love that, super popular right now. Have you thought about using Push to Open hardware instead of a pull notch? We do them both but I’ve really liked the Push to Open hardware lately

Full overlay cabinets look so good. What color you going with?

Love that, any time you increase more surface area for glue/adhesion it’s a good day

@@SupernalPaintingUSA Biscuits are really only good for alignment. Not much structural difference.

Love it. You feel it makes alignment easier than clamps and pocket screws?

My favorite comment ladies and gentlemen right here. Haha no seriously though I appreciate that! Definitely an adjustment to speak to a camera lense. We’ve been filming so much recently I’m excited to get all these new videos up

Oh man it’s fantastic, I’ve used several inch calculators but this one is my go to, it should be on the Apple or Google store as Feet and Inch Calculator. It saves a ton of time for sure

@@SupernalPaintingUSA Found it! Feet and Inch Calculator on the Apple App Store. Fantastic to help keep your fractions straight... So helpful!

Oh yeah it makes all fractional math way faster, you can mess with the settings at ton to personalize it too which I’ve done

Hey thanks! I think so too

Hey there! Yes this was a UV 1 Import Birch, so is the purpose to paint on the inside of the cabinets or outside of cabinets? my thoughts would vary pretty greatly depending on what part of the cabinet is being painted

@@SupernalPaintingUSA I was looking at painting the uv cured side. Nice work on the channel by the way! I think this channel will blow up.

Okay sweet, so painting UV coated side on the outside of cabinets is pretty simple, scuff sand it (but don’t burn through the UV coating, the surface will already be almost perfectly flat to begin with. Then like always prime it (we use industrial grade coatings for that but you could use architectural paint), scuff sand again and top coat. If you play your cards right you could be done with coating/painting it in two coats instead of three

And thanks on the channel! We’re excited to see what happens with it, tons of new footage coming with a lots of improvements

And to you as well!

Hey there! Sorry we're just now seeing this, in these scenarios we normally use a Artist brush and put 1-3 Light Coats, where we do one coat with the brush strokes going vertical and then one coat with them going horizontal and so on until the brushstrokes are minimal and aren't noticed. What did you end of doing to resolve the problem?

Love that! Very methodical. These Enamels are great at being rolled.

This actually is not, it’s a 1k industrial grade water based coating. CWC 400 Series

Here we used CW-1107, catalyzed I think 5%, we were going over stain so we didn’t need to block very much

Radiation?

Haha Right!? We knew we were going to Reface the cabinets, replace the countertops, and repaint all the walls, so masking wasn’t as crucial on this project 👍🏻

Then why would you tape at all? And don't you think it would be better/safer on your freshly resurfaced backsplash to do the demo before spraying? I can tell your new at it by the way you spray, let me know if you ever need any advice/help I will be glad to help. Treat everything like a Corvette,or a Cadillac. 😇

Didn’t want a lot of overspray that would make the kitchen unsightly while waiting on doors to be made. If our demo was sloppy? Then of course, ours wasn’t here. Appreciate the engagement boss

Great! Thanks so much. We really appreciate the support 🙏🏻

It’s holding up extremely well, we recently saw it in person and it looked like the day we did it, very uniform in color and sheen and no stains I could find.

@@SupernalPaintingUSA awesome! Thanks for update!

That’s all that really matters anyway right? Looks will always fade away

Oh yeah? If only that was the option every time in every circumstance haha

​@@SupernalPaintingUSA I wasn't trying to be mean. Just saying it looks exactly like what it is. A painted tile backsplash. You did a good job though.

Yeah it’s all good 🙏🏻 it does look painted for sure but in this case it wasn’t worth the 4-5 times as much money to have to heavily mask the granite, tear out the tile, replace the drywall, lay new tile, grout, etc. when we could do this in a evening and morning to mostly achieve brighter tile (white subway tiles) which was the goal

Haha thanks man

You are right it looks real cheap and nasty

You think so? What coating did you use?

@@SupernalPaintingUSA coating? i used the glaze removal? nasty stuff nasty to clean too but promised to remove the gloss from the tile surface and prep it and the paint was sticking too but then the peeling started maybe on backsplash youd have better luck since you're not walking on them but to paint tiles permanently ? i don't know if thats possible

Oh yeah the glaze removal hasn’t worked well from what we’ve seen. The only real good way to remove the gloss is to sand using a sponge to scuff the surface. However I wouldn’t paint Tiles on the floor. There’s not a great product on the market that can tolerate that much pressure on it daily that won’t compromise adhesion pretty quickly. You could maybe get a 2k Poly to stick but still iffy long term

@@SupernalPaintingUSA would you use a buffer? like a polisher grinder on tiles? i want to try it see how porous i can make it

You could try it, I doubt it would be adequate but you know what they say “necessity is the mother of invention” so you might find it works great 🤷🏻‍♂️

Sounds great! We’ve got a couple in the pipeline that are gonna start going up consistently

Haha yeah we’ve got a ton in the pipeline. We’ve gone through some changes in production to increase quality and value. They start back up in January.

hey u can see that he is very low in energy...lolol no energy to make more videos lolol

Haha 😂 yeah man and this was the slowest part of the year, we’re getting it under control to start back at it

For sure! One of those things that can feel daunting but is pretty easy with the right coating