![Juan Van Cleave](/img/default-banner.jpg)
- 2
- 898 187
Juan Van Cleave
Registrace 4. 02. 2016
DIY: 1947 Chevy Fleetline: Door Molding Removal
DIY: 1947 Chevy Fleetline: Door Molding Removal
zhlédnutí: 7 918
Video
DIY: Artillery Restoration: Rust Removal Project
zhlédnutí 890KPřed 8 lety
This is my first How To DIY video! I show how I kill rust and restore a Chevy Artillery wheel. Check it out, you won't believe your eyes! No chemicals necessary! Just 50% white distilled vinegar and 50% water!
If I have to listen to music I rather go to a music channel and listen all day.
I just did that to my 48 fleetline its crazy how the mouldings around windows are on there.
can i keep my tyer on the wheel or will it get damaged after a week of being in the vinegar?
Wow 😯 amazing.saves a lot of time.
Back when vinegar was cheap..
👌💯
Safe for chrome?
I was in ultimate shock.😲😲😲
Thanks for the technique, I just picked up a set of 15” arts for my 38 Chevrolet sedan. I was using a drill and wire wheels removing too much material in addition to the rust. I am going to use your technique, less destructive for my 1938 artillery’s and I will apply this to rear quarter window vents I have on the way too. Thanks again
Got to be a Wow for that. Nice video, great advice and result.
Fuck yeah
Good technique, good ingredients, n good vibes!!... you're da man, bro!! lv u..
Somebody tryed his way?
Bravo!!!!! 👏🏾 👏🏾👏🏾👏🏾👏🏾👏🏾👏🏾
Dang!! That is impressive!! Thanks and i5 will try it out. How do you seal the metal from fusting again? Clear coat.?
Muriatic acid would have done the same thing in a few hours instead of a week......as with any acid, including vinegar,.... you should use a plastic tub.
And that’s not rust coming off, that’s the paint underneath the dirt and surface rust...now you’ve exposed the fresh metal you need to spray it in a phosphoric acid to stop it flash rusting.
The catch is cleaning afterwards...it flash rusts immediately and the rusty water stains EVERYTHING. You need to be careful with vast parts too as it’ll eat into the metal.
Nice! Purple Power works immediately
Hate the smell of vinegar I can smell it through my phone
8 days each? 32 days to do a set. good work anyway
Would this work with painted over (Rust oleum Rust Reformer) rust, take the paint and the rust off?
Bloody awful music
What did u put on it to make it shine before you painted it because it looked like you put a coat of finish.
Go Raiders! Raider Nation for Life. Thanks for the video.
Is that really works sir?? Please
This is awesome. This formula works. Thank you very much for sharing this secret with us.
thankyou saved me 5bills on a set of 4...
I have two wheels that were done this way but were never neutralized and painted afterward. They are a disaster, might be ruined. Will try to save them because they are rare and expensive.
I’m going to my moms house to steal her vinegar lol
500 hundred hatters and climbing!! This is awesome bro! Go Raiders!
After you took it out of the tub and washed it off it didn’t get surface rust ?
Damn bro thanks for this I’m restoring my 69’ c10 and the rims are like yours but I’d say a little bit worse I’m gonna buy a kid pool and fill it up with vinegar
That is amazing! Can't wait to try it!
Nice video! Trying to figure out how to remove the belt line trim on the the door. Any pointers?
Gotta gett the bolt on the back through the view port
I also like the electrolysis method.
That takes wayyyy to long
That was beautiful. I've heard about vinegar doing the trick but seeing is believing.
awesome
You can use acidic masonry cleaners to descale metals fast. Just watch your eyes.
That is amazing can't believe just the acid in vinegar does a job like that going to try it thanks for the vid
so what do u recommended putting on the wheel or piece that one would be working on. is there a bear metal sealer one would use to protect the metal before paint or powder?
Have you tried this method with Chrome Rims? Was just wondering if the vinegar would hurt the chrome .
Do not do this with chrome rims. You can and will permanently destroy the finish. It should only be done on steel rims. There will be a chemical reaction and it could make the chrome fall or flake off.
Thank God for the mute button
sir I have a honda brio inside door edges are rusted what would you recommend, please help me..
Rustoleum rust remover
wow!!! Thanks!!
Good shit mate you got it well done
This works with all rusty iron parts. Can heat up the water, and use a fishtank-bubbler to keep the water moving to increase time. Great vid! Dont forget to wash thourogly and treat bare metal fast, tends to rust quicker after this treatment. I use baking soda water to neutralize the acid..
Do you pour baking soda water on the bare metal?
Pure in Nature's Garden When using vinegar does not really require the baking soda if you wash well with water. But mixing baking soda will neutralize all azids
$15 worth of vinegar,no dice.Can get spare rim for that.
And what will you do with the other three?
It is the spare rim.Take the good one of the truck that was stolen and I just got it back!
6 bloody minutes. Put in solution.8 days, hose off. That's all Folks.