Video

How to order

Wifi, remote and an app? Surely it's one or, not both? All I want to know if you need a special "socket" or if the lightbulb itself has controller in it and is self-sufficient

Wow..nice sirr

brilliant thank you

AC driver LED is big up to microwave frequency to warm up weather down to 2 hz to cool weather. The metal use in filament is important

I’d pay good money for that jig!!!

Nice information 👍

Thank you so much!

Nice video!

Tip 9 - check Ze first. Tip 10- clarify continuity of cpc (R1+R2). Tip11 - Carry out Insulation resistance test between L/N L/E N/E

Since, the lumens have doubled at the same power, and the cost has dropped +4x - the only negative is the newer ones last best case half as long as the older gen LEDs

hampson jim lamothe scotts dobermans kennel cough off cutter bug off

Can we connect a 3 meter or 5 meter led strip (12 volts, 20 watt per meter , 240 led per meter ) to a 12 volt car battery directly without drivers , assume passive cooling is provided for led strip.

Hey! How does the driver with an wide output voltage match the voltage of the LED?

You forgetting about dimmable drivers ,triacs ?😁

I’m looking to connect 8x 1m led strips which are at 400mA, 4.8W/m and 12V, I’m trying to connect these to a switch in the room what driver should I use?

Kitchen fitters put led strips in our kitchen, and after 6 months, the lights went dim. Fitter has us used a 12v DC 30w LED Converter 2.5A, 100-240v AC. Is this led transformer the correct specification do you think? It's a small to medium-sized kitchen and leds just run under wall units and inside a glass cupboard.

I am replacing the led driver of my ceiling light, can i use output regulated current of 750mA where the old one is only 660mA? The rest of the spec are the same.

Sir Why my LED light is blinking after replacement of Constant current LED driver ?

I want to replace a wall light with 5 LED strip lights (for a shelving unit). Do I just connect a driver to the existing wall light switch and the LED strips? I don't have a power socket nearby.

how can i stop my LED lights to blinking

Teco’s Classic GU10 dimmable spotlights are a perfect fit for spot lighting and deliver warm halogen-like light. They are compatible with most existing fixtures are designed as a retrofit replacement for halogen or incandescent spots. LEDlamps deliver huge energy savings and minimize maintenance cost. They also has excellent compatibility to various dimmers provided by different manufacturers. ◆ Real replacement of 75W Halogen reflector ◆ Delivers 575lm light output with merely 7.5W power consumpion ◆ Four different beam angles: 10° 24° 36° and 60° ◆ Ra＞90 ◆ Compatible with both leading edge and trailing edge dimmers ◆ L70 life up to 25000hrs, 3 years limited warranty

This music is awful.😒

Hello there, thank you for the information. May I ask where to get a led driver Dc output 280mA? Again thanks

Playback speed x1.25 Thank me later

wow

Amperes is written wit a capital A since the nit I named after a person . I The video the Units Hold nube Whitney as mA

I have what I believe to be a full spectrum led grow light. The main issue is that it's a cheaper setup and the LED drivers (4) are unmarked and two of the 4 are not working. How can I test them and how can I determine which drivers would be needed to replace the non working ones? I would greatly appreciate any helpful information! Thank you in advance!

I have just replaced a 50W halogen bulb with a 5W (35W equivalent) MR16 LED bulb. I have also replaced the driver with an Aurora AU-LED 16T constant voltage driver 12V 1-16W. The bulb strobes like a disco . Can anyone tell me what I have got wrong.

I have the ones with the IR remote control. No way would I use one that connected to WiFi or phone.

Thank you very much.. You are such amazing people

Hi Sir Can I charge my 12 volt battery which I taken from my bycicle using led driver ?

Hi I have a question. I have 9 led downlights of 24w each with its driver. I wanted to know if I can replace the nine drivers that each one comes with and power them all with a single 300W driver.

I was planning to fire up 50pcs of 3v diodes. Since I dont have a driver I used CP charger with an output of 5v. I used a converter to stepped the volts down to 3v.

Is there any universal led tube light driver for 40 w t8 model ,,

Hello. The led transformator where did you fix it?

Thank you for the great video, what if I want to run some LED’s from a charge pack?

Hi, Do you do training courses/days etc?

How to make 24v ac input led driver

What about a dual CV CC driver - can that be used for LED strips?

Not a word on LED driver efficiency 😔

I’m supply mass ufo panel light,simplicity cheap and easy to install, contact me i will send you the picture and details💡💡💡

My problem is that I was trying to replace my faulty Constant Current driver with a Constant Voltage driver.

I’ve been looking for this version with the male connection thank you so much!

i have an led light for my aquarium original driver broke, but it was using a 3 pin meaning 3 wires for the dual light switch blue and white, do you know what type of driver I need for 3 wire of my light. any info would be much apreciated.

The light just arrived Tuesday installed it imgs.love/SRetrofitLight?Д2 that afternoon very easy and simple to set up made the adjustments and seems to be doing what I wanted to do. That is to light up my garage when I go through the doorway.

Thanks for share this knowledge.

As a newbie to downlight stuff i was hoping this video would explain me how and where and when to hook the earth wire on our downlight that doesn't provide the earth wire socket out of the box.

Was the music really necessary to the purpose of the video?... I don't think so and it's way too loud.

Could a downlight meant for a 60mm cutout be fitted in a 70mm cutout?