Video

thank you very mach I appreciate you🙏🙏🙏

The plug may occasionally need some oil for threading but only oil that will smolder off

Thanks my friend great video

And he will not have a clutch down the road all that greese going to sling inside clutch smh

P.s guys please stay away from this guy!!!Do not listen to anything comes out his mouth...You will end up setting on side of a road or pushing it back home trust me nuthing he saying is true let alone make since.... (PEOPLE!!!!!! Stay away from those one piece heads their junk and they run way to hot alsoits harder to inspect the inside of the cylinder with a one piece also if you have to do part work it's a lot harder all around it's a very bad design stay away from the one piece jug always go for a two-piece!!! Unless you like red and hot 🔥🔥

No one should be taking any type of advice from this dude.Squish the rings in b4 tryna jam in the cylinder with one hand. I understanding you have a camera in the other hand just put the camera down it only takes a few seconds to do it the correct way.This is the main reason people have very bad luck with these type of engines because they decide to listen to idiots like this what a moron!!! I never put anyone down for any type of CZcams video they make but stuff like this makes me really really boils my blood.. Call yourself giving people advice you need to take advice from someone else other than where you're learning from because your advice is ass backwards my friend. I wouldn't take your advice if I just popped my head out of my mother's womb. Definitely the most misleading and ass backwards video I ever seen about motorized bikes on CZcams you can't get no dumber than this. What a waste of time for me watching and for his brain comprehending and turning it into a thought

Worst advice or is this a Joke .....this is what not to do GREASE ON CLUTCH LMFAO 🤣 ....DONT DO ANYTHING THAT HE DOES IN THIS VIDEO ....

And I'm honestly considering getting a motorized bike mostly because I sometimes get too tired to walk either to or from work.

but it is very low speed 10 miles in 30 min

To be honest i hope you give the people that buy your bikes a warranty

didn't you try gasket cement?

Where is back brake?

happy april fools day

What moter is it n where do I get it

Stop flexing at the start

There are so many things wrong with what you are doing its crazy from putting all that grease on your clutch plate to thread lock on your spark plug 😂😂😂 this should be a comedy (PLEASE NOBODY DO THIS TO YOUR ENGINE)

Hello 🚴 u just passed by me place 😅

Were you are nature from?

It looks good.Good luck.

word of advice . dont watch this . go to la hover , build break fix, etc ,etc those guys have 100s of videos with really great info . these motors need very easy work to make run good dirt cheap.

BR detectado kkk esse sotaque ai n engana

Wish mine started so easy dang

cool video thanks for upload

Thank you sir

can the police pull u over for having this and ask for dirving licence (those 50cc ones or smth) ?

I have a virago 250 also but I feel like mine tops out around 60 any ideas or are u running this thing at 7-8k down the I-95

your turn signal was kept on lmao

Nice ride!

If you would angle the engine differently the carb will fit like it's supposed to

On that one did you have to bend the exhaust for the pedal clearance because I built one almost identical to it with the same motor and bike

Do not put lock tight on the spark plug

How many miles did you Ride the bike on I-95

❤

Were did your get this motor from i can't find its anywhere please let me know the name of the company or Were you got it please and thank you and have an amazing blessed night 🙏❤️💯👑👑💯❤️🙏

Do your thing bro. I like your style. Real. Simple and Easy.. No matrix involved. I appreciate this.👍🏼 Mixing on point

It's fun isn't it?! Just wait till you start modifying it. Thanks for the ride.

This hobby looks fun but I have no experience in automotive or mechanical engineering

Nice, what size engine

Nice bike bro thanks for the ride

Very goog video!!!

All engines possess inherent imperfections. Smoothing the surfaces can undoubtedly alleviate leaking concerns. The lower halves (cases) remain consistent across the board. The issue appears to stem from over-torquing the stud, resulting in thread damage within the stud hole. Excessive stud torque often leads to leakage problems. Merely avoiding leaks with a single-piece jug doesn't denote superiority; it could be a stroke of luck with that specific kit. I, too, encountered leakage problems with single-piece jugs. Utilizing two gaskets isn't a panacea; it typically exacerbates problems and diminishes power. Resolving leakage entails replacing gaskets and applying oil to them. After the engine warms up, studs and screws expand, potentially causing leaks. Hence, it's crucial to re-torque them during full heat soak. Additionally, favor non-painted kits to avert sealing and heat-related issues. The amount of grease applied seems excessive, risking interference with the clutch basket and plate, leading to slippage. Avoiding the use of locktite on the sparkplug is advisable to prevent complications. A malfunctioning head with imperfections may contribute to leaks. Opting for a two-piece jug and substituting the head with a proper high-compression variant can rectify this. If the case halves are uneven, acquire a suitable case or dismantle and level it. Considering your relatively nascent experience in this hobby, your knowledge about these China doll kits may be limited. It's sincerely hoped that individuals won't follow your advice and inadvertently damage their engines. Finally, acquiring the cheapest kits may occasionally yield subpar results.

Watching just a few minutes of this video the only thing I learned was that YOU SHOULD NOT BE GIVING ADVICE ON HOW TO DO ANYTHING WITH THESE MOTORS. This was a very bad video to make because you are learning yourself how to build them. I’m not trying to to be mean but it’s videos like this and people like you that make “HOW TO VIDEOS” that others watch and think it’s good advice and it’s just not. There’s nothing wrong with showing your experience but you need to explain that this is NOT a how to video and rather just your experience with the motors and that you DO NOT know what you’re doing.

i have one it doesnt take long to go down a block.

My opinions are completely bass acwards from yours

bruh that is easy u only got to go 20 miles a hour

If it's put together properly it will not leak ... the one piece cylinder is not better...they run hotter ......no clue.... WOW

Not bad: Skipping two stop signs one after another. Do you WANT to lose your driver licence?😮

Did they sell

🍺😆🔥

Smartest autozome mechanic