Video

wish I would have seen your video before I put my skimmer in! cutting the gasket and mounting the skimmer before cutting the hole is genius!

They tell you only to use the cord that you need, don't through all the blue cord in the pool, only what you need. It works good only sometimes the cord gets tanagled.

I should have watched your video. I followed another one where they traced out the gasket and then cut the hole. It was going great until the last inch when the razor knife went through like butter and made a slit a good 2 inches longer than my template! I had done another one like you did without any problems, but the video I watched said not to split the gasket. Well, we know how that went. Now I'm in the process of patching my two-inch slice past the marks.

How well has the liner held up with the hayward skimmer? I want to do this but am worried about longevity.

Hey thanks for the vid hello from alaska, question now that you've had your gaurds installed for a bit of time, have you had any bending in the tubes or plates where things connect? Do the pegs ever get in the way while your tring to mount or dismount the quad? Any questionable issues with these im thinking about getting a set of them for my foreman any tips or info greatly appreciated l.

If you pull that flywheel (which I wouldn't do) make sure that special Belleville washer is installed cup size towards the flywheel. It's slightly concave and if installed wrong the flywheel will not be seated firmly and could sheer off the sheer key. You have to look closely because it looks like an ordinary washer.

Can you please show me pics of the pump cover you made and where did you get the arm to hold the lid open

What brand pump can you please post a link for it

Cut the hole for the first. Then you don't have to cut your gasket. Its like that because it supposed to fit in the hole on both sides as a solid piece. thats what makes seal

Ez Money 🎉

bro, I want to ask, I just bought an ATV 125. When I tried it, sorry, when I was walking, I walked to the right / pulled over, right? until it hit a trash can. It's also really moving, not stable, even though my steering position feels straight, 2. It feels like I'm going to turn really hard, maybe because of the big tires? 3. Please provide tips for getting used to using an ATV

Say I have one and where can I get parts for mine it's the same one has this one

Did you use a 12 foot or 16 foot 2×4?

I just finished installing these on a new Highlander. The windows seem to be functioning fine. This is about the fifth set of these that I have installed on various makes of cars. In the past the deflectors I installed had a blunt edge where the window first makes contact. I would bevel this edge with a file. On the latest pair I just installed the edge is bevelled already.

For the hard part of fishing the parts through use a fishing line and Romex wire or metal coat hanger. Well done I made one to hang from the hood and bypass bad gas and a dirty fuel tank. This works well on older carbureted engines.

Привет. Неужели нельзя было сделать тройник в самой воде? Там где подключается скиммер?

Thanks so much!

Great video. I have a 2002 Rubicon and have to do this same project. I'm goign to just put the kit in it.

Looks like the best and easiest way I’ve found so far.

He does not know what he's doing at all

I need one

When rubber is exposed to petrolatum, the rubber can become brittle and cracked due to the solvents in the petrolatum. The petrolatum can also cause the rubber to swell and harden, reducing its elasticity and leading to eventual failure.

At it again I see! I must say, I appreciate this adventure. Thanks for bringing us viewers along. May be the most redneck thing I’ve ever seen anyone do and on the same note, I’ve never been more proud to be an American 😂😂

The gasket never had been separated it coming to be inserted at the vinyl square

How much depth did u lose with the Hayward skimmer ?

Do you recommend the economy or the competition

Prefer the hitich that dosent bang yours shins it more flush with bumper.

Trunk deck lid

That is sweet, 74 was probably the cut off.

50 year old everything

Round headlighted caddy coupe

I love that tractor

Roughly how long did it take you to build this? Also, what paint did you use?

I don't like how you have to have less water in the pool when using the Hayward, that's my biggest gripe.

Thank you sir!! 🫡

Do you still have it? I’m in need for 1988 Mercury Grand Marquis

It's gutless

You’re right it was very annoying to get that thing

Just got one today! My grandad gave it to me, hadn’t ran in 9 years!! Still had old fuel in it. Drained it out and put fresh mix gas in. Stated on the 5th pull!!

Cómo hiciste la mesita para la bomba

3 days later..😅

My d7 looks a lot like your dozer

You from Michigan ? Kalamazoo is my Home town

It's so nice to see your son working with you, it reminds me of me and my father many years ago on an old D4. He taught me so much by letting me try whatever I asked for (within my skills and within reason). Great memories, thank you for filming and posting this.

You didn’t have to take the points out of it you could’ve left them in

Don’t slice the gasket . It works better left as a butterfly gasket

How are they working out for you? Better than OEM? Would you buy again?

Just installed on my 2003 Toyota Highlander. Note: Use some Trim Restore Serum and take a Qtip and put in channel of rubber. Then get a cloth and locking tweezers and rub the serum in the channel and use these to pull rubber open as my dad put the corners in and started to pop in channel it went in very smoothly. We couldn’t get the auto window off so make sure you click the window up in increments. The front windows worked great by doing this. Thank you for this video! Gotta love YT community!

Good video sir 😊

My town has gas stations that offer non ethanol