Video

Could you share the blueprint?

One of the Best videos i've seen on youtube for diy. Such a great methodically planned and executed video. thank you

Pretty awesome video man, thank you.

I’d like to get this kit for my Ford Excursion. I need to take some measurements!

Really love this. I have the same trailer and have been trying to figure out how to add sides so I can haul debris without it falling through. So thank you for the video.

Hi where do you buy the washer/ bushing for hindge assembly?(what do you call it or parts number)I need to change mine,thanks

Good job drilling those holes. That was impressive. Very impressive.

Fantastic! Great design and very informative!

Hi, how much is your unit prssure sir?

Way to precise and technical for my redneck a$$

Great job thanks for sharing, you make it look possible to make this at home to make a superior and more affordable table than the certiflat table. I know prices fluctuate, but how much do you figure this cost in materials to build your table?

Looks nice, but how did you plan for dealing with the heat buildup? Compressors produce a lot of heat. Forced air circulation would help. For noise, lining the inside with rockwool would make a big difference. An automatic drain on the compressor would be a good idea. Also, if you don't have one, a refrigerated air dryer will really help your plasma.

Bravissimo 👍🏿 ❤

Great video. I want to make a similar one for my Excursion. I want to be able to put chairs on top of it so we can sit on the roof. Do you think it is sturdy enough to do that? Any changes you would make?

Great job! Simple. Effective. Love it. I see room for improvement! Overtime the cyclic forces on the frame can cause fatigue failures in the welds. You should disassemble for painting because it would look slick. While the frame is bare you can add some knee braces in the top crossbar like you did in the bottom crossbar then go a step further and add some plates to “box in” the whole sides of all the channels. There isn’t much there in the webs of those channels so adding side plates creates a double box section which is considerably stiffer. Add a custom logo or name it with some lettering with your cnc table! “When it’s Built not Bought, it’s Custom not Cost’em”

Good job!

how mush $ ? can u make one for me ?

waooooo

I built almost the same shed for my shop underfloor vacuum system.The only diferencce was I used rdgid insutation in all the walls. Man what a difference. Great job on you and keep up the good work. Pete

the anti-wobble device is a game changer

Nice work kid👍🏻

Box your C iron on both sides, that should eliminate the deflection your getting. PS I'm very impressed with the things you are doing, engineering and fabricating. Keep it up, everything should pay off for you if it hasn't already.

I wonder maybe create a pad for the jacks to stand on and remove the wheels as security measure? If I wasn't in an HOA, I would get a trailer too, but I can always borrow one in exchange for a case of beer with buddies.

How much did your modifications reduce your load capacity.

Man, thievery goes hard where you are apparently

I’m in the process of moving my bender onto an engine stand and am I glad I watched this video! I was about to cut off the rotating part and just have a plate welded on to bend horizontal, but your idea makes so much more sense to have both options. Great job !

Hello. Great stuff. May I ask you what CAD program you used during this video?

офигеть, какой у них порядок на металлобазе... "загнивающий" запад, что тут скажешь...

Sure a nice job! That trailer should give you plenty of service.

well done ,

Do you know if they have safety locks for the big Tex utility trailers 6x10? If so, where can I purchase them from?

Stumbled upon this randomly, browsing the interwebs, had to come on here afterwards, to compliment your work. Trailer looks great, and i totally dig your "lets not drill into this brand new trailer" way of thinking. Fantastic work man 🙏

Great build - absolutely stealing your wooden wall build for our Karavan trailer.

Nice clean build 😊! GOOD JOB!!!

Very nice workmanship

Great job brother ! I would like to ask your opinon for other projects that I am working on. How can I keep in touch with you ?

id sleep on it afterwards

boss the length value in the table its length measure in sketch , How I can get the cut length not original length?

Enjoyed your video and learned a lot. Thanks for sharing it with us!

Great Video! This really helped me build a proper weldment. You mention in the video that the Solidworks file is available for download, but I only see the PDF. Is the Solidworks available somewhere?

Good job brother! I’m looking to get a 4X8 utility trailer and probably do some of these mods.

Had an idea, but I don't know if it would ever come in to play. Since the fingers are different widths, would maybe making the back guide slide side to side be a worthwhile upgrade? Can't think of a specific instance, but I haven't needed a finger brake yet.

That's a great idea! I've been leaning toward a Roguefab bender because it can do the vertical orientation, but it's out of my price range at the moment for something I won't use alot. Combining this with the Woodward Fab clone from Amazon might get it in my range.

One can't install enough locks on a trailer or what is on the trailer. No lock is infallible, so it is better to layer with multiple locks. At least that will slow them down or maybe deter the thief from taking what is yours. It is definitely getting worse out there for people who have no morals.

Where can you buy and how much?

My trailer was stolen 😢

awesome video, ty!! quick question are you using 3/8 for the table grid ?

Love the wheels and color choices.

Thanks for the upgrades. I have an 8 foot trailer with a single tongue (like your boat trailer) rather than many V types. I have attached a hand crank cable winch to the tongue exactly like your boat trailer. This not only helps with loading, but after loading I use it to hold the tarp down.

Great job. 👊🏻👊🏻👊🏻