Video

I finally got the bottom out after taking half the center console apart. I took everything apart exactly as described and heated it twice just as shown. It still won't work and now the cd player won't work either. I give up.

Neat idea but I cant even get the bottom of that faceplate off. The whole top is loose but the bottom wont budge

and how much is the torque of this head in Nm

Doesn’t work for me , i finally bought an adapter on ebay and it is not perfect but at least works 7/10

i need to replace the rear emergency brake pads . Seen a few vids on here from mostly phllipines or thailand.......looking for one with a bit clearer english instructions and if possible, the canadian part's prices for the do it yoursefer.

Excelente tutorial . Just the application I was looking for. Easy and convenient

Is this still working well? Wondered whether it might put too much strain on motor compared to original plastic wheel slipping (which I figure is a bit like a clutch).

Good vedio ,so before replacing with new oil is there anything else liquid used to clean up the engine inside before replacement with new oil

How much bleach to disinfect a 275 gal tote?

Just remember to remove the grease zest before you unbolt the spindle and install grease zert once installed and grease it 😊

The one to the right is a late 21 because all the 24s are all tube frame with kawasaki 23 hp.

It’s the customer place to redo them in to good condition 😢😢😢

Had to drill holes to install the zerts on them because they lock up and don’t turn Cheap brand 😢😢😢

my picture is pink..

75w-140 x3 75w-90 x2

Using two pry tools in tandems any pry large or small works wonders

Worked great. Gave it 2, 3-4 second shots and done. Total time about 1/2 hour with testing before I reassembled radio. Thank you

Thanks a lot. Absolutely true 👍.

'Thanks for sharing 👍

Can I set it and save it and then use it again a few days later? Is there any other way other than pressing "C" to turn the display back on?

Tim foil trick worked mint. Up and listening again. Tks

I was planning on replacing every fluid on my polaris sportsman 570 trail 2023 thanks for great guide❤

Thanks!

Pro-tip: clip the top of the butane refill bottle in 45 degrees about 1cm from the top. If you push straight from the top, it fills the bottle :)

Excellent video, many thanks

Called 53's in Indiana.

Excellent doityourselfer video!

Very neatly built with precision cutting using router. However this kind of equipment isn’t normally available to DIYers. Also the gate doesn’t seem too sturdy.

Don't buy this chainsaw, removing the battery is to hard.

These are different models. The 1 you have from lowes is a smaller chassis and engine combo with the same size 52" deck. Lowes sells the same bigger 1 too. At leaat the lowes in my areas do as they have both the smaller and bigger 1 plus the onyx one. 😂

Very useful video. Worked like a charm. Thank you!

This worked perfect for me! Had to remove extra parts of center console to get the cover off but was really easy. Thanks for the video

Thanks!!

Did you check the date stamp on the one from Lowe’s? They are always selling previous years models .. I returned mine and got a BadBoy Maverick HD, WAY NICER Machine!

hi, how did you disconnect the Starter Lockout Cable?

I can’t seem to locate that brand of butane (Mag Torch). Any suggestions for an alternative? I live in Ontario

So the rear differential and transmission oil the same?

That was a great fix! Mine had no am/fm for years and I used Sirius xm. But last week my speakers started cutting out every 5 seconds. This fixed all my problems.

A great Idea. IMO. I Will do it on my Mower. 👍

How much was it??

Well..... I "GUESS" That's not a BAD IDEA, 🤷‍♂, However those are SEALED BEARINGS from the Factory. I suppose it'll work, but again, Sealed Bearing's are Just That, and they are Made for the Application, If anything I would Cross reference those Bearing's with a Better Part # / Brand and Just Replace the Bearings if you are gonna go that Far to Tear it Apart like that. Then, what I would Do rather than FILL That whole Cavity with Expensive Grease???? Buy yourself some FLUID FILM, Or WOOL WAX and Spray the Inside Cavity with it before you Replace the Bearing and Put it back together and for OVER KILL SPRAY the NEW Bearings before you Install them. It'll Keep the RUST Away and you want be waisting your Hard earned MONEY On GREASE Needlessly. Just my "OPINION". But a Good Video on Installation of a ZERK FITTING. And I Like your Grease Fitting on the end of your Grease Gun...... Is that a LOCK N LUBE???? Nice...

Awesome. Thank you! I've never changed a starter from above. Great video

Thank you!!!

Nice stove..the flame looks great 👍

Big Thank You for this video. Yesterday after 12 years my radio start to cut out sound in my 2012 Ram 1500. Used heat gun, count to 4 on each side and radio working fine now. Thanks.

Best tutorial I've seen yet! Thank you very much! The shack looks great! 👍

That chain at 3 min looks loose

Thanks- great video. My 301.8c has power, but won't crank...

Thank you. Just what is happening in my Dodge Caravan. Will try this soon.

Man, thanks a lot! I replaced the antenna on my wrangler and then I didn’t have any station sound. I thought I might have messed something up with the antenna. Crazy how that went out at the same time.