Video

What filter? Great video!

Your pretty good for being so young. You obviously grew up around it so it was easier tonlearn when it came time. I grew up the same way. I got tons of hate in the union when the old timers knew a fraction of what i knew lol. They dont like it when a "kid" is better than the foremen. Lol. Keep on getting it bro. Doing great. You can tell you have been taught right

Thanks bro

Not sure if you would know, my switch just stopped working and so did the tilt. Does that switch power the tilt? Thanks. Great Video. 😊

Ijust disconnected the compressor n turn breaker on if stays on bad commp.

It’s good to see you back on here.

I just wanted to let you know this video right here save me so much time and money. I really appreciate it. God bless on another note. I think it’s really stupid how the Dodge ram does not come with a Van blower motor filter my truck didn’t have one either and I had to do the same thing you did in this video to make my AC start blowing harder. God bless and thank you again very much.

If I had a nickel for every time I broke, bent, or lost the pilot bit for a hole saw... I could probably buy a new set of hole saws. Nicely done!

smart kid

23:10 In India and Pakistan there are tradesmen who actually cut open hermetic compressors and repair the reed valves, then weld the two halves together. Search CZcams for "refrigerator compressor REPAIR"

10:58 That two speed mechanical drive is crazy smart. It would be interesting to measure the two pistons and compute the displacements for stage 1 and 2. Is it split 50/100%, or more like 33/100%. I think the tubular pipes and chamber on top are a type of "muffler" to quiet the pulses in the refrigerant line. 16:25 Old style Whirlpool washing machine motors had windings for two forward speeds and one reverse speed. How many power terminals on that "two speed" compressor? Many single speed compressors have just 3 terminals. 28:30 Looks like there are only 3 wires on terminal block.

Captive Aire is horrible. Whatever temperature it is outside will be the temp inside. In the summer your kitchen will be hot and miserable. In the winter it will be cold and miserable. Call me old fashioned but i like hoods that just vent not hoods controlling the exhaust.

Great video. I’ve got the tiniest on/off switch under my throttle. Took me forever to find it when I first got the boat.

Does it still shoot with the messed up trigger ?

I do not agree with you on the mulberries. They are my favorite wild berries of all berries. I don't like too much tart in my fruits. As a tropical boy, i grow up on a lot of sweet fruits, mulberries do give me that little bit of tropic with berry flavor. I forage a lot for berries in the summer time, and this year i found a lot of mulberries, service berries, black berries and raspberries. I froze them and used them to make smoothies in the mornings.

if you park for long time best to leave parking brake off

Not sure why but I usually install my valves so that you have to turn them up to turn them on. I guess that I am afraid of the gravity monster.

Lame.

Well done!

Awesome. Love to see you guys figuring it out. Good job

Ah. I see I am not the only one with the makeshift "bathroom" that gets you out of the 1 Bath market. The only positive is house has credit for 2 bathrooms, I can set up that 2nd bathroom however I want and wherever I want in the basement. After some thought, I am going with Pex A and will just eat the cost of the proprietary expander tool. Its all basement plumbing so no contact with sunlight. Pex A is unrestricted flow vs B which has smaller fittings than the pipes. This affects flow. A can kink and be repaired via heat gun, B needs kinks cut out. A just isn't as flexible, but it is flexible enough to avoid the use of many 90 degree fittings. This really helps design a project where you don't bury any fittings inside walls. All pipe.

"Showering in your basement has kind of fallen out of favor" 🤣😂

Thanks

When working a system with any hydrocarbon refrigerant, put the system on your vacuum pump once you have removed the refrigerant, while you are getting your equipment from your work vehicle, cut the pipes where possible and it will be just like working on a normal system, don’t be afraid be careful, I have worked with this refrigerant for 10 years , do a training course.

i don't like the idea of pex for cold water supply that's used for drinking and cooking, who knows what it leaches. okay for hot water.

good for a kiddie pool so it's not freezing.

Is outside electrical outlet GFI??????????

Just get an electric valve out of a wahing machine, connect hot and cold to it and out to the outside tap. add a water tight three possition switch outside near tap,provide proper wiring and power to work the electric valve in the bacement! switch selects either hot or cold. you can get crazy and instead of three possition switch use a four possition switch and you can then have hot,cold,or warm, or off........

Your daughter is so adorable and smart just like her dad.

Love around the house projects like this! Hope you and yours had a Happy 4th!

Must be nice not to hit rock.

Great information I wish Brunswick Automarts Service Department had. My truck has no air flow intermittently though. This does not seem to be my fix. Any ideas?

Where did you order the motor from

You can put these drains outside to use with a garden hose right?

What I just looked at hurt my eyes 🤕 In Russia, we just remove the top panel completely and clean the evaporator😂

And thank you for having a link for the part attached!

Thank You for the video!

Ty for the video, 2011 ram same problem, couldn't figure it out until I seen the video. I did what you did except cutting the square and hole, but fixed the problem now I can feel cold air and good flow. Ty again really helped

There was screws on the thing you cut a whole it’s able to be removed 😂 no need for violence

If you go the speed of horses and ir will work properly, will need at least a ford n series tractor. I have the john deere version and dangle right along in 1st gear and the plate with the fingers gets to bouncing up and down shaking as it should so the dirt falls through and the potatoes are on top of the ground.

My heratge done the exact same thing after around 900 or more rounds in the same place I replaced it and has had no problem ever since must be a similar problem for more people than I thought good video buddy 👍

Refrigerants differ at density latent heat of vaporisation mass flow rate heat transfer capacity boiling point therefore you get a gas that absorb and transfer same amount of heat in 30% of the time of another gas and maybe even its compressor run on lower current cause it’s operate at lower pressure or the compression ratio or use different size of piston or rotary high low rpm high low torque also run for way shorter time that why they use different ones in different applications

have this probablemente with my 2004 lincoln aviator, dosent come with a cabin air filter and i’ve been looking countless forums to no avail, until i saw this, thank you so much brotha 👍🏽

What's that loud Rap music in the background? But ok you even had hearing goggles on😂

You really know your stuff! It really takes a lot to understand everything you explained. Great job!

Bro how about all the rust falling in the ice weewwwwwwwwww

Ilike the access hole idea! How much spare room did you have around your cut? I'm wondering if I can make a bigger hole than you did or if there is something in there i would absolutely grenade if i didn't stay in that rectangle area where the sticker is located. Thanks!

Hi Reuben, Great video. Question: I have to replace the 4 rubber vibration absorbers that the motor housing screws down on top of - I e. the design by which the motor screws into the base of the fan housing. I am wondering about the 4 threaded studs on the base of the motor - not the bolts that screw through the holes in the motor housing that tie into those 4 rubber bushings that hold the motor in place. Do those 4 bottom threaded studs in the motor get screwed to anything, or are they just alignment or guide studs? It looked like when you pulled the motor out, and put it back in, those 4 threaded studs were not tightened to anything, they just align the motor to the base of the fan housing? Am I right on that? It seems like the only things that get bolted down are the two set screws that affix the motor shaft to the fan, and the 4 motor housing bolts that screw into the rubber mounting absorber studs? Am I right on that? Thise rubber vibration mounting bushings that attach the motor to the face of the fan housing appear to just rest in the aluminium base of the fan housing - is that tight? The 4 rubber vibration studs that the motor bolts in to on my fan have deteriorated and broke. My motor and fan are running fine - but the motor is just resting on the top of the housing - nolonger affixed to the housing... not good So I'm thinking I could buy the 4 little rubber vibration studs from Captive Aire and just replace them and rebolt the motor on properly. What do you think? Are those 4 rubber mounting studs merely positioned into the aluminium base of the fan and held in place because the motor mounting bolts - once rescrewed in - hold the motor and rubber mounting studs in place? Any advice would be most helpful... Sincerely, Mike (cafemadmoose@gmail.com) 808-442-2424

I planted 51 plants on March this year and they are ready producing

Nice video!