Video

Id rather that over a huge pile of spaghetti and getting your whole nozzle ruined then it takes 30 minutes to clean off all the plastic

At least you have some salvageable parts. I have a couple monstrosities i keep on display to remind me of my mistakes. Lol

Thankfully the prints are still usable but I still can’t comprehend what happened or why 😂

Hi, could this configuration be used with a 1 mm nozzle?

What material is this?😮

You should set your print speed a little faster

I was doubting the “softness” until you touched it. Absolutely mind-boggling.

Also, if that stuff is non-toxic, then it'd be GREAT to make toddler toys with.

That's awesome. Kudos!!

Thats an insanely slow printer, what is it?

Whole lot of infill.... if you got that much by ~30 hours then id fully expect this to be finished in a business week. Roughly counting for spool changes and down time between the aforementioned. Why so much if it only holds a couple pounds or so?

i gasped when i saw you first put the controller on it. that's awesome man

Dude that's mind blowing!

You look like if cleveland from family guy was white

that's a pretty sick controller stand

Do you all want to see more with this foaming TPU material?

You said 3D print a treadmill next

This didn't need 3 parts man its just annoying splitting what could be a 30-second short into 3 parts multiple videos multiple days, but keep the content coming

that's a neat idea :)

Who else is excited for the print to finish? Hopefully we will get to show that in part 3 soon!

im too invested now for some reason. I'll make sure to watch the conclusion now.

Let’s hope so!

Stay tuned for part 2! Will this print make it the next 36 hours?

i through a v6 volcano on mine. i hate the kobra series honestly, any other brand is fine

This was my first MRRF and I had a blast! It was super cool to get to meet you in person brother!

So the timer just sets off an audible alarm but does not switch the heater off? This box seems to be the best of a bad lot, but I wish someone would do it properly! Heating filament in a closed box will not dry it. I suspect all these systems rely on you opening the box while is is still warm to vent off the damp, wet air. If you let it cool down before opening, the moisture will just condense again on the filament (although maybe it relies on the desiccant to absorb it, in which case heating the air is pointless and it would be just as effective to circulate cold air). What it needs is separate exhaust and circulation fans and a controller that heats the air with just the circulation fan running, then stops the fan and heater and runs the exhaust fan to change the warm, wet air for cold dry air from outside, then repeats. It could also have a weight sensor on the spool. When the weight stops reducing you have removed all the water possible and the controller can shut the box off altogether to avoid wasting energy. I may have to buy one of these when they are available again and modify it to do the job properly!

I am trying to connect my mega x to Pronterface and the baud rate is giving me problems. Have you had any issues with this

Haha love the opening clip! Looks like a lot of fun (:

Let's Go Pens!!! I really need to get to one of these... Much different atmosphere vs RAPID 😂 Awesome footage and editing 🤘🤘

Great footage! You love to see it!!

Cool recap. Thank you very much for sharing. Looked like it was an awesome event.

What do you want to see for MRRF 2025 or another rep rap festival in the future?

I need this !!! How much

How about PrusaSlicer ??

Assuming the process is the same for 0.2 or 0.6 nozzles. Right?

Yessss let's goo!!! 🔥🔥🔥

Love it!

Go check out their shop here: www.emberprototypes.com/

Hello B1GJano, have you ever tried replacing the Y-Axis Motor? I noticed my Y-axis motor can stop moving at certain points during prints. Right now I tried some printing residue cleaning around the motor, if this does not work I'm looking to replace and some tips are always great help. :D

How can i remove the ptfe tube

🤘🤘

Do you dry your filament? Be honest!

You lost my interest at 15 seconds on a FIFTY SECOND INTRO. Please cut it down to 10 seconds or so. Great vid btw - I think? Never made it that far.

How about supports? Mine are welding on or too low…

yesterday I came across a print bed issue, somehow during prints the bed (Y-axis) gets jammed and keeps printing in place. I forced it loose and just tried re-tightening the screws, seems to works now. I'm going to try a big print tomorrow again to make sure.

Bro printed four at once, I have issues printing a single one dqmmm beast you r

Just my opinion this printer is not very comfortable in the least for a beginner. The whole laser engraving thing is sub par at best. The extruder is crap. The automatic leveling is garbage. I wouldn't recommend it to anyone. Enders are much better.

Are you able to share the curs profile

I think I disagree on the Z axis motor opinion. As someone that is replacing an Anet A8 that has dual Z axis motors with the Sovol SV06(it is being delivered today) I have had issues where my Z axis motors would turn differently at times. This initially causes print issues but then leads to binding where it just stops working all together. I considered making a belt setup to force both Z axis motors to spin together but the current pricing on the Sovol stuff made me decide to just replace the whole thing.

OK, now you're just showing off😜 Cool track too.