Video

Mucho voltaje para solo 2 tubos.

Nice setup and that looks like alot of gas. Its definitely a whole lot for 20V at 1 A with tap water. Unless your tap water have alot of electrolyte in it. Are you measuring efficiency? For reference, Faraday electrolysis maximum is 1.23 watts produce 0.0114 L/min of HHO at room temperature and pressure. The wierd part is the volatge required for the two half rection is 2.06V but only 1.23V is needed in reality, which is the greater of the two half reactions ( 1.23V + 0.83V). The voltrolysis process is definitely different than the electrolysis process. But it seems that there are more than one way to get the voltrolysis process to reach overunity. This makes research and experimenting challenging. Are you using a replica of mayer patent for your switching circuit? Did you make any changes?

Hydrogen technology 🚓🚕 Hydrogen help the combustion process to run engine more efficieently.and carbon-free fuel burnning. HHO gas burn a lot faster then gasoline or petrol. Hydrogen power miracle gas remove carbon build up in the combustion chamber and boost engine power and torique. Reduse carbon emission ) restores better fuel economy. Hho car kit prolonging engine life and engine oil life. Like a new car!!! Engine runs smoother and cleaner to make your car 0 carbon emissions Boost engine power and torque Better acceleration . An efficient hho car kit lower the engine temperature more then 100 degree F. Hho car kit reduce car maintenance charges. Cleaner engine running. Reducing engine noise due to the faster fuel burning. Hho car kits works nicely requires no modifications in the car engine. No side effects on car engine. Engine start quickly safe your car battery. No more petrol or diesel smoke or smell. Hho system is very simple. Hho kit installation time is about two hours to make your car a low cost hy-brid.

Remove electrons and switch off the bond. The Voltage Polarisation Process.. When the gas processor ionises the air to remove electrons. This air is mixed with water to make water fuel. When this water fuel is ionised. The processed air with missing electrons gives the oxygen a very strong electron gravity and is used to remove electrons from the water molecule. Causing a polarity flip and so splitting the molecule.. It’s a triggering process! He said, This is the voltage polarisation of the water molecule.. The covalent bond is equal to the two shared electrons and if you remove these electrons. The oxygen atom will flip back to a positive charge instantly repelling the atoms.. Processing the air in his air gas processor he removes up to 4 electrons from the oxygen in air and uses this as a tool by dissolving the processed air into the water in the way air is dissolved to keep fish alive in a fish tank.. This is what he called his water fuel.. If you don't make the water fuel first then all of his inventions will not work as described.. I hope this is helpful to you.. You must understand when he says combustible gas atoms he is always referring to is the oxygen in the ambient air. Combustible gas atoms are not hydrogen and oxygen. Also In all his patents he refers to electrolysis as the prior art The voltage polarisation of the water molecule is not electrolysis. It’s a set of conditions set up to trigger a reaction. Like I said above he strips the electrons from the oxygen in air in his small air gas processor and keeps the oxygen atom stable with light energy.Then dissolves this prepared gas into the water tank. This is his water fuel. Now all of Stan's arrangements will work as he stated. When you use the VIC to charge the cell up to the dielectric properties of water without dielectric breakdown you excite the water molecule and also the dissolved oxygen held dormant by the dielectric properties of water. When the electrical stress re-excites the processed oxygen from the air. The oxygen has such a larger attraction force over the two covalent electrons it removes the shared electrons and as Stan says for every action there is an equal and opposite reaction. When those electrons are removed the oxygen atom swings from negative to positive charge and in so breaks and repels the atom structure. He says 5 seconds of excitation you will get 90 seconds of production..In turn the electrostatic fields used to ionise the water and combustible gas atoms otherwise known as water fuel, attract the now separated atoms towards the electrodes. This is not electrolysis, it is the birth of a new technology and now you know!! Any questions just give me a shout.Hope this helps you with your interest. Thanks Tony. czcams.com/users/clipUgkxIobrQrZVXglOaAgxttBYfTvPzTFwXdca?si=qET09j2icEAxubA9

Come on. . . . . dunia harus diramaikan dengan W F C!!

Congratulations, That's a lot of Gas 🤠

Just recycle the water through a 60 horse turbine system a Tesla would run till something broke fix it and keep going

thank you for sharing this inspiring footage! would you be so kind to break down Stan's patent into components in English. God bless his soul, hes transition to heaven is an outer loss for humanity, but his written wording is challenging to understand. btw are you related to Stan?

How would u install 120vac on a car?

Just a suggestion you should try hooking it up to a generator and film it

My friend it's a good job.can I use only 8xa circuit to have a good amount of a gas

bom dia, desculpe mas esse aparelho é o PWM

boa tarde sou do BRAZIL, como faço para comprar este aparelho

Hi there buddy! I got one of this but can't remember how to hook it up back into the truck. Can u help me with the wire harnes!?

How Much Voltage are you using as input?

how much LPM does this system produce with this included cell

No Vic?

Beatifull. These photos make me very happy. Thanks for sharing.

Stan Mayer used a high voltage with just a table water the mystery is how to power a CAR engine with HHO thats it any way i liked the vid ;)

I am interested, I build the cpu interface and hydrogen cells for automotive use. these are not your plate cells that you see. they are high pressure injection systems. i am looking for a good Stan Meyers board person.

Thanks, yes, all components and design is by Stansdream, based on Stan's original Electrical Polarization Process box. The goal is to have a hydrogen control box that drivers can adjust in realtime for the best fuel savings. Stay tuned!

you mean i am first. very nice job, like the hightech box. looks real i can see the leds. good production. Your boards or is credit due. David A. Puchta

The Mayer System is the right method. Don t need to use soda, bicarbonate or other shit. Only pure water

do you know how Meyers used a variac as variable charging choke on his early work?

@tectalabyss I believe the assistant shown was James W., but there was more than one assistant. One originally came to Stan as a skeptic, but after he worked with Stan and saw his devices working before his own eyes, he became one of Stan's strongest supporters.

you need to show lpm with this technology

@theoneagain The 8xa is not designed for a dry cell and we aren't interested in that. Why waste your time mixing up different designs - They are two different technologies.

@theoneagain That may be true, but we don't want to be like them, we are following Stan's design - not theirs. What's the point in going through all the effort if in the end you are only using normal electrolysis?

@stanmeyerlives believe you me i was using the 8xa i will be doing a video shortly 6.5 volts at 5 amps why that is i dont know with a 16 plate dry cell and bubbling crazy but with K.O.H no K.O.H no gas i have tried everything different coils transformers the lot

@stanmeyerlives my coils are wrong when i change them i get different readings. show gas production from your cell using a plastic bottle and you ll see it wont even be a litre a minute

@stanmeyerlives of course everyone is doing it but not with the 8xa. THEY are all using K.O.H PWMs and distilled water and high amps 25 to 30 at least

yes i know but i ha d it running today on my dry cell if you dont use KOH it doesnt work the only way is koh it was using just 40 watts of power and i had bubbling which is impossible with a pwm the downfall is my bridge rectifier it can only handle 8 amps so i m gonna change that to a 40 amp 600 volt and give it some amperage to see if i can an effecient gas production my aim is to make a home heating unit just with 300watts of power

@theoneagain You're certainly not using Stan's design if you have current that high. Stan used HIGH voltage but LOW current. You are using plain electrolysis it appears, which defeats the whole purpose! PWM units are made for the 'brute force' traditional electrolysis, it generates lots of heat, dissolves the metal plates in the cell, and that is not what we want here.

@theoneagain Wrong again - KOH and NAoH are both caustic, dangerous, and eat some engine parts. The last thing I want in my vehicle is my aluminum heads dissolving. This is the DEMO unit made for the patent office, and no adjustments are needed - build it per Stan's specs and it works, simple as that. You came too late to tell me it doesn't work because I've already seen it work personally countless times!

@theoneagain Speak for yourself. I know of many people using this circuit to SUPPLEMENT the fuel in their cars for better mileage. No one is talking about running an engine completely on water - YET. We are not interested in running a dry cell. The idea no one has made any decent gas output is also false. This puts out more gas than any of Stan's circuits yet tested. You can't take ideas from everywhere, put them all together and expect it to work. You must do what Stan did to get his results...

stans technology is more than it just being plug and play it needs to be fine tuned like a piano otherwise you get nothing and the 8xa is just a percentage of the technology you need to get crazy gas output to run an engine.PWM A DRY CELL AND SOME K.O.H is your best bet for now

this circuit will not work on a dry cell i have done my tests without k.o.h no production at all. With K.O.H you get some production i have at a stream of bubbles at 60 watts 5 amps 6.4 volts it has its limitations need to make a pwm using the same signal from this board . No one has come up with any descent gas output with this circuit i am having trouble myself and will not work in an automobile with a pwm i get 3 litre per minute at 300 watts enough to make a torch.

As you can see in the scope, the circuit uses pulsating dc at the output, which is what Stan focused on. There is no resonance, but lots of gas output. This was Stan's demo box for the patent office. His later design tracked the changing conditions in the fuel cell and adjusted to it to keep it in resonance. Much more to come...

I regret having to ban a user, but we are here to discuss Stan's designs, not to compare egos. I now see why this user was banned from other forums in the past. The 8XA design is everything Stan said it was, and it DOES have amp restriction, if built per Stan's specs. It is only a stepping stone to deeper concepts, but it is an excellent HHO producing device. In short, it works exactly as Stan said it would. We do not need to re-invent the wheel, but just follow what Stan left

@h2opower The video speaks for itself. The circuit works and produces as Stan promised at low current. That is enough for me. You have submitted some good work, but I believe you tend to go on rabbit trails too much - and waste time on things unrelated to Stan's original designs. Stan believed in KISS - Keep It Simple Stupid. I appreciate your comments, but I trust Stan's original designs and the suggestions of one who actually measured the dunebuggy for himself, in person. More coming soon!

@h2opower You simply build the 8xa as per the patent. Nothing else is required. I've built it myself and I know it works - I've seen it run with my own eyes. No ionization or anything else is needed. Simply build it and plug it in. There IS amp restriction if the coil is built per Stans specs. There is no variable power supply needed - just a powerstat as Stan documented. Simply follow the patent - nothing more, nothing less.

@waterpower2012 Eventually we may offer this in a completed, ready to use form...

@h2opower Frequency is not a major factor in the 8xa, as it has no ability to produce resonance. It is not a resonant circuit, but only a demo unit Stan created for the patent office. It is, however, a much more efficient HHO producer than any other circuit I've used so far, and this makes it excellent for use in vehicles, etc. The best thing is, NO Electrolyte needed!

@theoneagain The coil is as per the patent, 18AWG wire, bifilar, 4 rows, 28 total turns per row. Approx. 760uH per coil when finished. Start wires go to cell, finish to circuit.

what coil did you use how many turns

its kicking mate you wanna make some use of the gas show a flame or something

im using two seperate circuits the 8xa with its own transformer and the voltage intensifier circuit on its own the 8xa is connectected to the gate of the scr as the ground from the cell back to full wave bridge rectifier going back to the variable transformer like you said keeping both circuit independent from one of each other

@theoneagain: The 8XA will work good for you - just a word to the wise: When connecting it, be sure the HV ground and the signal board grounds are isolated (not connected, as shown in Stan's patent). If you connect them accidentally, you will have unpredictable results (this is the voice of experience!) Good luck

@theoneagain No worries. If you're referring to our cd collection on the site, it is well worth the $200 for all it has. It has literally everything from schematics, designs, parts, etc. on almost all of Meyer's dunebuggy stuff. We do plan to have more stuff available as we test out designs, but the kit for the 8XA will be more like $30 for a board and $50 for a kit (parts and board). We also plan to have a kit for Stan's steam resonator (so your cells do not freeze in the winter!)

ive been foloowing up on this 8xa for sometime now i have purchased one myself but waiting for my variable transformer i will be performing with my 16 plate dry cell hopefully when i get my variable i have everyhting else diodes 8xa scr and coils so hope it kicks ass cant wait