Paul Dark
Paul Dark
  • 20
  • 337 116

Video

Mevotech TTX Sway Bar Link Review. 2014 Ram 1500
zhlédnutí 288Před 6 měsíci
Was pleasantly surprised with the quality of Mevotech TTX, check it out! 2014 Ram 1500. No, I'm not sponsored by them.
Electric Fan Upgrade Ram 1500 tips
zhlédnutí 31Před 6 měsíci
There are other videos explaining the benefits and how to upgrade to an Electric Only fan for Ram 1500 (mine is 2014) check them for a full guide. This is a follow-up on my update and little tips to make sure you wont have problems.
Your fan clutch doesn't budge? How to quickly remove fan clutch with no special tools. Ram 1500
zhlédnutí 154Před 6 měsíci
I had a lot of trouble removing the fan clutch and went through tons of videos of how to do it, but nothing worked. This is a method I came up with.
Tesla Model S Failed Air Suspension, Low To The Ground. Fixed
zhlédnutí 12KPřed rokem
In this video I'm showing how to fix failed air suspension on Tesla Model S.
2012 Ram 1500 Brake line rusted, leaks and its discontinued? Need to bend similar line?
zhlédnutí 319Před rokem
One of my old videos - lost the brakes on the truck, luckily was parked. It was leaking fluid like crazy (right next to driver side rear) and brake pedal was super soft. Truck with this condition CAN NOT be driven, it will need to be towed. The brake line that busted is no longer in production, so you will need to buy the one above it and fit it? Didn't film the whole process, but gave some poi...
How To Tow a Large Cargo Van (Sprinter Etc.) With A Tow Bar
zhlédnutí 761Před rokem
One of my old videos, I bought a non working Sprinter Van (170 XL High Roof) and needed it towed 300 miles or so. The only option to tow these is flat bed tow truck and even then its too tall, to do it properly you need a semi truck with step deck or a car hauler trailer, so you don't clip the traffic lights (its too tall) But I didn't want to spend a bunch of money and time trying to get this ...
2009 Land Rover LR2 Freelander 2. Long Crank, Long Start Problem. No Codes. Fuel Leak. FIXED!
zhlédnutí 5KPřed rokem
In this video I will show you a very common leak on Land Rovers (pretty much all models). The car will hesitate to start, you might have out of the blue hesitation while driving and very strong raw gas smell outside. You will need to replace part of the fuel pump (its just a top cap), but they are not sold separately for this model, so what I did is - I bought a cheap aftermarket fuel pump and ...
2012 Dodge Ram 1500, Ignition but DOESNT START or STARTS AFTER FEW TRIES. FIXED!
zhlédnutí 15KPřed 3 lety
So my 2012 Ram 1500 had a starting issue. When I attempted to to start it - security light would blink and nothing happened. Dash did light up. It would eventually start after I tried to do it 2-3-4 times. - It could be the battery (check the battery make sure its checks out as good) - Rusted battery wires or terminals (clean/replace) - Faulty ignition switch (most unlikely) After all fixed - c...
2012 Dodge Ram 1500 Leaky Gas Cap message, Check Engine Very Code - Very Small Air leak FIXED!
zhlédnutí 3KPřed 3 lety
My 2012 Ram had a "Very Small Leak" and gas cap message, I will show you how I fixed it.
How to perform an oil change on big (semi) truck yourself and why? Also what does used oil tell us?
zhlédnutí 1,1KPřed 4 lety
In this video I will explain how to change oil on 2011 International 4300 with Maxxforce DT motor. The procedure will be the same for almost any truck or even smaller vehicle. Also will go alittle bit into why do you change oil in diesel truck and how to check if its time. (Testing lab I use is Blackstone labs).
How to replace Manual Coleman Mach RV thermostat with a modern DIGITAL PRECISE unit.
zhlédnutí 27KPřed 4 lety
In this video I will show you how to swap Coleman Mach manual (usually very glitchy) Rv thermostat with a digital unit. Do that and your AC will cycle like at home. No more too hot or too cold. The unit I have replaced it with has one extra function which is gas heat, if you only have one heater source you can replace it with digital unit that has just one heating option. My wife's nails are gr...
How to remove transmission pan, fluid change, transmission service on 2009 Sprinter 2500
zhlédnutí 1,7KPřed 4 lety
In this video I will show you how I removed the transmission pan for transmission service such as fluid and filter change or transmission hydraulic "brain" service. There is crossmember on the way and I will show you how to go around it.
PROPER WAY to Reset or Program TPMS (tire pressure sensors) on Nissan or Infiniti at home
zhlédnutí 85KPřed 4 lety
This video will show you how you program TPMS on Sentra with special tool or no tools at all. When I show you "the tap" this suppose to be done with paperclip not just a finger nail lol And also, whats important is, once you turn on the ignition, you tap the paperclip 6 times against metal WITHIN first 10 seconds (you gotta be quick) The most important part is - you need to wait 1 minute before...
How to fix noisy, jerky, leaky power steering. 2011 International 4300 or any truck.
zhlédnutí 548Před 4 lety
I have topped off my power system with power steering fluid and all above problems started to appear.In your case they might appear because of the worn fluid. This International truck takes motor oil as PS fluid, NOT real power steering fluid. In this video I will show you how to flush and fill the power steering system on my International 4300 truck with Maxxforce DT motor, procedure is simila...
How replace blown semi truck or box truck tire with the spare on side of the road, all by yourself.
zhlédnutí 2,1KPřed 4 lety
How replace blown semi truck or box truck tire with the spare on side of the road, all by yourself.
How to remove most modern keys (flat, "laser cut") that broke inside ignition lock and also unstuck.
zhlédnutí 396Před 4 lety
How to remove most modern keys (flat, "laser cut") that broke inside ignition lock and also unstuck.
How To Check Error Codes on Most International trucks with no tools. DuraStar, ProStar, MaxxForce
zhlédnutí 122KPřed 5 lety
How To Check Error Codes on Most International trucks with no tools. DuraStar, ProStar, MaxxForce
2011 International 4300 Electric Problem, Abs brake light, Limp mode, Truck Wash fail, Maxxforce DT
zhlédnutí 40KPřed 5 lety
2011 International 4300 Electric Problem, Abs brake light, Limp mode, Truck Wash fail, Maxxforce DT
2011 International 4300 lost power, runs rough, air in fuel system. MaxxForce DT
zhlédnutí 21KPřed 6 lety
2011 International 4300 lost power, runs rough, air in fuel system. MaxxForce DT

Komentáře

  • @matthewlloyd7806
    @matthewlloyd7806 Před 4 dny

    I have one shock loosing pressure and scheduled service with Tesla. Now they say three shocks need to be replaced. After seeing your post I informed Tesla to cease repairs until the technician speaks with me first. At the same time the A/C cut on and off a few times. Now I am questioning the relays.

  • @blakevincent2332
    @blakevincent2332 Před 10 dny

    Hey I grinded my brake hose on my tire and I bought a new brake hose to replace it without the steel brake line I take it I’ll have to replace both I tried taking the 11mm off the housing but it seemed stuck

  • @dreamkiss4u
    @dreamkiss4u Před měsícem

    So what was the estimate they told you to fix it? It seems like alot of work and i for that icon message and i don't feel the AC anymore working.... but my air suspension is working normal tho.

  • @donneyhanchard457
    @donneyhanchard457 Před 2 měsíci

    No throwing of hands. Throw chest over rass line

  • @seamusrispin1967
    @seamusrispin1967 Před 2 měsíci

    Hi, Great video, thanks for sharing. I hope you don’t mind me asking for advice. I have a Tesla Model S 2017 Electric Motor 100D AWD. The suspension system is flat. There is an error showing up, as follows: Air suspension compressor disabled - your vehicle will not rise. There is a 40A fuse that controls the air compressor (it's in a slightly different position than the one in your video). This has blown and when I replace it with a new 40A fuse, it blows immediately. Am I right in concluding that the air compressor itself is faulty? If this is the case, and I purchase a second-hand one, how compatible are these compressors or will I have to purchase from a 2017 model? Thanks in advance, and I look forward to hearing back from you With kind regards, Seamus

    • @Mitrofanovalex
      @Mitrofanovalex Před měsícem

      Hi, did you find the solution? I have the same symptoms on Model X

    • @seamusrispin1967
      @seamusrispin1967 Před měsícem

      @@Mitrofanovalex Hi, Sorry about the delay in replying to you. There is a 40A fuse on the fuse-box and if it's blown, replace it. If it blows again, there is a 95% chance it's your Air Compressor Unit for your suspensions. In my case, I purchased a second-hand one and changed it in about 1 hour. If you are doing it yourself, remove the compression unit and only buy the same part number as there are a few different types. I hope this helps, Seamus

    • @Mitrofanovalex
      @Mitrofanovalex Před měsícem

      @@seamusrispin1967 Thanks for your reply. Yes, in my case the problem was in the compressor, but I was able to fix it myself. The magnet in the engine came off, I glued it on and everything works fine. Removing and installing the compressor is not at all difficult. The main problem is moisture; you need to change the granules in the dehumidifier often.

    • @seamusrispin1967
      @seamusrispin1967 Před měsícem

      @@Mitrofanovalex That is great, well done and thanks for the advice.

  • @TheDrAkira
    @TheDrAkira Před 2 měsíci

    YEEEEEESSSSS!!! THANK YOU MAN!! I was going crazy trying the "rolling" procedure in my 350z but with that little orange tool it was just straight forward dumb proof easy! THANK YOU!

  • @TheDrAkira
    @TheDrAkira Před 2 měsíci

    Just received the tool and gonna start doing the procedure right now! Wish me luck!

  • @yourworstfear
    @yourworstfear Před 2 měsíci

    not one on 2016

  • @cool2180
    @cool2180 Před 2 měsíci

    They should sell the s without the air suspension. I wouldn't want to deal with all that lol.

    • @rootkitxx
      @rootkitxx Před 2 měsíci

      I have seen some with coil suspension

  • @vetlefosser6420
    @vetlefosser6420 Před 3 měsíci

    In Norway Tesla takes 200$ just to calibrate the airsuspention🥲

  • @alkhashtee
    @alkhashtee Před 3 měsíci

    Thank you for this valuable tips for towing a Sprinter. But unfortunately mine is the older model, and the bumper is not removable.

  • @panch1962
    @panch1962 Před 3 měsíci

    How do eliminate them

  • @armandolau7003
    @armandolau7003 Před 4 měsíci

    Hello. Maybe you can help. I have a Tesla S P85 from 2013. A few days ago, when I get to the car the front suspension is all down. The car hits on every bump, so it's stop till that day. I already change the compressor, because I few days earlier, I ear the compressor working non stop for a almost a hour. I thougt it's bronken. How ever, after change it, no sound I get from the compressor. I receive the solenoid yesterday to change, but I do not now if it's gone work. Now after two weeks, I have all the suspensions down. Do you have any clue? Change the tubes to the suspension? When it hapens, only the from suspension is down. The yellow light first apears, then a red one comes.

    • @rootkitxx
      @rootkitxx Před 2 měsíci

      Sounds like you have a leak somewhere if compressor works non stop

  • @pollywollydo
    @pollywollydo Před 4 měsíci

    If you have that much water in the system it would be a good idea to look @ the gel crystals in the pump ( dry them out ) as it will “ wash”the grease from the pump bigend bearing ( very noisy before it gives up) 😖. The bearing can be replaced but it’s not easy

  • @youtuberlive3923
    @youtuberlive3923 Před 4 měsíci

    Where i can find the wire reset of nissan versa 2019?

  • @JIMPLAYLIST100
    @JIMPLAYLIST100 Před 4 měsíci

    Poor video. This could've just been an article since he didn't show us anything. A waste for a video.

  • @arielista
    @arielista Před 5 měsíci

    My 2015 Pathfinder has that plug but has many wires

  • @jmjaxson
    @jmjaxson Před 5 měsíci

    What type of scanner do you have Paul Dark? I'd like to get a scanner that would be able to find those faults. Also, would any 'bluetooth scanner' like Blue Driver Pro or OBDLink MX+ perform those functions? Thanks.

  • @benkanobe7500
    @benkanobe7500 Před 5 měsíci

    Where did you get the little fitting you replaced the original with?

    • @rootkitxx
      @rootkitxx Před 2 měsíci

      Actually you can get one from Tesla, but this is brass airline fitting that is used on trucks

  • @benkanobe7500
    @benkanobe7500 Před 5 měsíci

    I think that is a brilliant diagnosis! Great thinking on your part.

  • @ilyacharny4611
    @ilyacharny4611 Před 6 měsíci

    Do you know if X has about same system. Tesla wants to charge $5800 to fix. Completely out of their minds)

    • @rootkitxx
      @rootkitxx Před 2 měsíci

      I would assume it's about the same

  • @theemmanuelshow2858
    @theemmanuelshow2858 Před 6 měsíci

    How would you review the performance so far?

    • @rootkitxx
      @rootkitxx Před 2 měsíci

      Great. I actually bought more TTX suspension parts since that video

  • @rootkitxx
    @rootkitxx Před 6 měsíci

    When I said Roll I meant Rotate Counterclockwise to loosen it (its a reverse thread fan clutch on this truck)

  • @vaughncannon2414
    @vaughncannon2414 Před 7 měsíci

    Is it the same for a 2018 nissan kick

  • @philipjosephmeza
    @philipjosephmeza Před 8 měsíci

    Does anyone know where is the reset wire in a nv200?

  • @sandwich818
    @sandwich818 Před 8 měsíci

    Hey Paul. Love the video. Can you post the 'parts' that you used to fix your S? Looking for links to order similar parts. :) Thanks.

    • @rootkitxx
      @rootkitxx Před 6 měsíci

      Well, you can go to Tesla and give them that relay number, it's like $6. For a air line fix it's a 1/4" brass coupling for air lines, you can buy at places like fleet pride, it's like $4

  • @marcepan8142
    @marcepan8142 Před 9 měsíci

    Does it work on Honda?

  • @hermanmoseby1471
    @hermanmoseby1471 Před 9 měsíci

    Hello, my P85D gets the red light “active air suspension automatic self leveling disable” mostly when it becomes freezing outside. I don’t know how to fix it, I think it’s ice somewhere in the system but is there anyway solution to this?

    • @upinderjitsidhu9066
      @upinderjitsidhu9066 Před 9 měsíci

      supposed to be 200psi using nitrogen to represurize it

    • @pablopicasso8502
      @pablopicasso8502 Před 8 měsíci

      Rewatch the video. Water would be in the distribution block

    • @rootkitxx
      @rootkitxx Před 6 měsíci

      You will need to warm it up to the point that water in suspension control block thaws. You can take the block off too and make sure to blow all the water out of it, preferably with 100% alcohol flush after (alcohol absorbs water and dries up quick) There is a practice of using alcohol in air lines on big trucks. You may drop some alcohol down the line to the distribution block so it goes through it, once it's unfrozen. Don't add too much, it will collect at the air tank, absorb water and slush around there - you don't want that. Just enough to clear all that water out of there and "dry the lines"

  • @tacroom12
    @tacroom12 Před 9 měsíci

    Ended up doing a fuel relay bypass. Problem solved.

    • @alexskybun2956
      @alexskybun2956 Před 2 měsíci

      So it was same problem as it showed in a video? Sometimes start sometimes not?

    • @tacroom12
      @tacroom12 Před 2 měsíci

      @@alexskybun2956 yes. So what I did was test my fuel pump. Fuel pump was good. Apparently the fuel relay is built into the tipm and cannot be replaced like a fuse like non Chrysler vehicles. I found vertical visions bypass for about 60$. Takes about 30 seconds to install. There’s CZcams videos on it. I installed last winter and even the single digit morning’s it would start up first try. A strong start too. No puttering and no rpm’s dropping. Make sure and get the bypass that has no wiring because that one is not a permanent solution.

  • @SkedgySky
    @SkedgySky Před 10 měsíci

    Doing this tonight. It's so annoying!!

    • @rootkitxx
      @rootkitxx Před 6 měsíci

      Sometimes you want to meet the engineers that designed this....:)

  • @619MMH
    @619MMH Před 10 měsíci

    Thank you this worked for my 09 Infiniti

  • @tacroom12
    @tacroom12 Před 10 měsíci

    Thank you. My 2012 5.7 is doing this. Pretty consistently as well. Going to remove terminals and clean everything up.

  • @luisulloa80
    @luisulloa80 Před 11 měsíci

    Does this work on Infiniti? I have a 2009 g37, purchased a oem tpms from the TPMS website they said all I had to do was a relearn

  • @keithrupp1
    @keithrupp1 Před 11 měsíci

    I'm in a similar situation, I have a 2012 Telsa Model S P85 lowrider. I swapped the relays, and I'm about to see if I'm getting electricity to the pump. Before you replaced the top fitting, do you have any idea of a "normal" pressure in the top reservoir?

    • @pablopicasso8502
      @pablopicasso8502 Před 9 měsíci

      Don't remember. Don't have that fitting there anymore, so can't check the pressure. Can anyone that still has the Schrader fitting check on the pressure? I think I read somewhere that it was at 75psi, but I could be wrong

    • @rootkitxx
      @rootkitxx Před 6 měsíci

      Pressure really don't matter, as long as it's raising up and suspension works good and no error logo, you are fine.

  • @extendedepicmusic5017

    You should also do the AC condensation tube. Right now it is dripping onto the battery pack, That has caused moisture getting inside the pack.

  • @alexzee3043
    @alexzee3043 Před rokem

    I need to program Sentra 2022 does this method work also?

  • @46REBORN
    @46REBORN Před rokem

    Pressure problem on my 2004 international. Truck kept shutting off. Thanks for sharing this information. Very helpful 🙏🏾

  • @techgeek4499
    @techgeek4499 Před rokem

    Tesla didn’t even offer me to try calibrating it to see if air nitrogen would hold!!!!!

    • @rootkitxx
      @rootkitxx Před 6 měsíci

      That's what I would do to refill it with nitrogen. - Lower the suspension down all the way - Enable "jack mode" (suspension leveling disabled) - Put a vacuum pump on the system to get slight vacuum in there (connect to Schrader valve I showed you removed) - Turn off pump. - Then, while under vacuum, connect your nitrogen tank to vacuum pump (purge the hose prior) and fillthe tank up to pressure you need. Similar to refilling a/c system.

  • @interstatescrew2218

    How do you know which code is the problem?

  • @mikeelize20
    @mikeelize20 Před rokem

    Mine reads “Diagnostic Codes are not available from EGC”

  • @jCapois23
    @jCapois23 Před rokem

    Thanks will try this tomorrow on my Nissan versa 08

  • @ssecret8657
    @ssecret8657 Před rokem

    Did anyone try this on an Infiniti Q70 2016? Does not work for me

  • @PeaceIsWithin1
    @PeaceIsWithin1 Před rokem

    So do “Pervious codes”mean it’s not the problem

    • @rootkitxx
      @rootkitxx Před rokem

      Yes. They store in memory, when problem fixed they will disappear from "warning list"

  • @jkgv1740
    @jkgv1740 Před rokem

    THANK YOU!

  • @abrasit
    @abrasit Před rokem

    On my son's 2007 Murano this process worked fine, EXCEPT for the fact that when I waited the minute as you suggested the TPMS light stopped flashing. In my case it worked perfectly when I immediately programmed each sensor after getting the TPMS light flashing. Each sensor only took about 1-2 seconds to program. The hazard lights flashed briefly upon successful programming for each one. I also didn't need to remove any of the plastic trim as the small white wire harness device was accessible just looking underneath. (I laid on my back and put the parking brake on to give me clear access.)

    • @rootkitxx
      @rootkitxx Před rokem

      Glad it worked, good experience for others to follow on 07 Murano

  • @Alan-vg5pk
    @Alan-vg5pk Před rokem

    Worked on a 2004 Murano. Thanks for the video.

  • @ginnyl7949
    @ginnyl7949 Před rokem

    do you have a written out directions for this anywhere ?

    • @rootkitxx
      @rootkitxx Před rokem

      Nope, of you want you can post it here for everybody.

  • @FrankGerald.
    @FrankGerald. Před rokem

    Hep Paul. This is a great video. My Truck is making the same sound. Will there be a misfire code If there is air in fuel lines? Or does a Misfire code and this sound simply mean there is a bad injector?

  • @alialdaffaie1752
    @alialdaffaie1752 Před rokem

    I have the problem to it seems like the sensor wire needs to be replaced 😕 🙃

  • @daveymcmahon4601
    @daveymcmahon4601 Před rokem

    You are doing it the wrong way brother 😂 never put a bottle jack underneath a differential man