Video

Don't let your kid pick the music ,I have had enough of if you can't play ▶ play loud .I mean screaming unintelligible noise neverhas been music please

Are you guys going to drag week, since it's going in your area!

SCOTT IS ON ROIDS DUH, MY BENCH IS 430 AT 215 POUNDS. I DONE 465 FOR A SINGLE 405 FOR 6 REPS AND 285 FOR 20 AT 233 POUNDS NO ROIDS.

this could just be me being weird, but i think being able to see the transmission and being able to monitor the second it starts leaking is extremely useful. 1/8” lexan weighs .75lb/ft² and 20 gauge sheet steel(which id assume would be what a trans tunnel would be made of) weighs 1.5lb/ft². you’d be saving about .75lbs/ft² and would have one of the most unique trans tunnels in the game while also still having it protect you. weld in some zeus bolt tabs so you can get in easier and it will still be easily serviceable

Ok Steve, don't let us older young guys down!!!

He was raising and extending that can like it was paper

Love these crank driven superchargers. Looks like a much simpler system than the exhaust driven turbos.

we have 340 with ported edel rpm heads 9:2comp, bds 6/71 street blower with 19psi what made 670hp 7000rpm from tires with e85. 9.7 145mph at 3300lbs stick shift car💪🏻 more to come🤣

NA: 1263hp 25psi: 2741hp

**POP** goes the parachutes! Honestly I did laugh out loud because that's situational humor right there! 😂😂😂

No draw had the kid beet both times.

Old guys rule 👍😝

“Bad Bad product.. For you!” Steve.., how ‘bout “Betty”? Oh, that 1/2”trame thickness does seem like it might be weak, but you can’t tell that until it bends.

I would be tempted to ditch the water/meth and convert it to straight methanol at the track. Seal that street spec blower up nicely, run cooler....Make some 9 second power!

my bet is on steve

The word is stylus

Take caution guys. Flat bench can tear a pec easy, not to mention shoulder injury. If you’re still going to do it make sure your elbows are tucked near your torso to protect your shoulder.

Steve, havent had time to watch yet so... On an sbc mechanical pump w/Holley, it would use a max of 7ish lbs fuel pressure or so no? Would 7 or more lbs boost push back through the needle/seat orings and screw things up How do you handle that situation? Not really into putting EFI on an old car Is the answer to build more cubes and limit boost to 6 lbs?

How much total timing did it end up with?

I always tell my son, be careful while playing with me because WE HAVE THAT OLD MAN STRENGTH, that still makes us the man of the house. Steve won by a second. It doesn't matter if you win by an inch or a mile. Winning is winning. (Dom). Steve has the best of two worlds. His own shop and his son work with him. Can't get better than that.

Wow! Steve aint no old man. Still in great shape. Must be living right.

Ive heard the most a regular sbc block can handle is around 800-900hp, how true is that?

Natty or Not?

Kids these days don't understand "old man strength" lol. Not saying Tim is old...

Lol was gonna cheekly say will it be cheaper but we all understand just because I can do it faster doesn't matter we are paying for precision

He was probably one of the coolest guests yall have had in a while

I bulked up when I was a young man. Enjoyed being really strong then. Wish I would have considered having to carry it around after 50 years old because muscle is heavier than fat of course. Then there’s the knees, hips, elbows, wrists, and hands that are shot. Would like to have not worn them out in the first half of my life. Hindsight is 20/20.

Dosent even have a clue what he is looking at!!!! can you feel my jealousy from here

To be blowned is nice but I rather be injected. Don't foul around and do a max bench. Do something you can do atleast four times.

That’s what I like, NOT A LS!!!!

Hey what kind of silicone or whatever are you guys using in between the dyno headers and the cylinder head? I might like to give it a try.

I'd like to know his body weight, cuz benching 230kg isn't a game, especially if it was in competition. I've benched in IPF and other Federations and can tell you that bouncing a bar off your chest with your hips raised 5ft in the air on your tippy toes isn't bench pressing!! At 54 years old at 93kg I competition benched 180kg which is a record in a few Federations but doesn't get me on the podium in IPF. But i'm not a gym rat and have a hugely busy real life schedule too. Hope to see both Steve and Kyle bench over 140kg, hoping it's regulation bench with the full pauses

How is Clark feeling?

Man Kyle has really grown. A couple years ago when I first started watching, he seemed very disinterested in all of it and now he really seems to be into it and naturally his camera presence is so much better. Love the content gents. Keep it up

Why is that big block Chevy such a small displacement?

vibration on a powdered rod will cause it to break. The greater the oil clearance the greater chance of the bearing hammereing out quicker.

I think you are wrong. Any hole should be machined perfectly round. So, shrink the bore and expand the bore at the same time? Rod bores that are out of round will cause a bearing out of round and you will get a worn out bearing quick. No more thatn .0005-0007 clearance.

Advertising 2500++ on 93 is false Steve . ✋️ Stop the BS .

Tenacity…. u gotta love Steve how he continues to go further no matter what problem/s he faces etc.. Great Channel

How do you guys come up with a base timing map for all these different engine combinations ? Like what factors come into play etc etc .. I know a whole video could be made on the subject

When you say put more timing in it, is it everywhere or only at a certain place ?

Great show, smart tuning, nice muscles Morris Men !!!

would like to learn more of Scotts program

this was funny, but I think Steve won , need to hit the gym some more lpl

Hmmmmm..... "control of the car" he says. So held into a race seat, how is he gonna move his arms across his chest? Just sayin

I need to get back to my personal best 180 on the Curl 260ish Bench but I know I could do a bit higher just dont want to get to big ... Cool Vid Lads

Work b4 play I totally get it you have to keep customers happy. Hopefully we see you around Friday

Here’s hoping that Steve is missing Sick Week to finish off the motor for Eagle 🤞

17:19 That's the Wile E. Coyote wind up dyno graph. 🤣

Please make the American flag SM t shirt again! mine is getting worn out and its my favorite ever!