Video

This a fun saw. Old antique😂😂😂. We ran 2 080s in the early 1980s. Low price on these. Don’t complain

Thanks 👍

I don’t believe you fuck we can’t see your not in camera when you make these videos go all the steps don’t stop fuck

What i do is clean 2-3 times with saddle soap, then apply 1-2 coats of the oil waiting 24 hours between coats, then i put 1 coat of the wax, with in 8 hours you will be able to tell if you applied too much wax. If you did just use your hand and rub the wax to heat it up the wip the excess off with a rag. Another good trick is after applying the wax is put your boots on a peet boot dryer for a few hours the wax will soak in faster.

Where is this at?

Props to dude for not cussing the top out. My video would be laced with alot of, "you sob, stupid mf, pos sob mf gd fkn pos"

Maybe in the future, the wood can be arranged neatly and then sprinkled with sawdust until it is all covered, then closed.

Wood chamber not sealed good enough

Maybe fire temp was to hot

Nice truck too👍

Read the back of most TWC3 oil bottles and it says plain as day "can be used in both water amd air cooled engine such as chain saws, string trimmers and leaf blowers"

Funny how you have absolutely no idea what you’re doing!

Does your urban logger squeak?

In 2024, wondering how these Danner light boots last?

Excellent idea with the hose and the valve or pinching off

i pour up to a gallon of diesel into my tank every fill up.

why dont you just slide the shoelaces on the beeswax then use heatgun to melt the wax into the laces?

I am after the alcohol for an alcohol torch . We have e85 in this part of the country so I am almost there .Have you any Ideas ?

Where do you dispose of the ethanol infused water? Can you pour vodka down the sink? This is not hate mail.

I nearly came my pants to that gas price

If you think leaded fuel is a good idea you must already be suffering from lead poisoning.

Debes tratar de explicar un poco mejor en mi opinión, gracias

Steel toe? If yes, how's the toe leather holding up?

The 070's and bigger 090's were uncomparable to today's Stihl saws. Low revving and loads of low end torque. Nearly impossible to stall. We used to run a 6ft guidebar on an 090. Chain used to whistle. Could refill petrol and oil with it still running through a big log!

To switch from gas to propane, is it as simple as flipping the switch from gas to propane amd jist starting it up? I was gifted this exact generator but have no manual. I assume that's what you do but wanna ask beforehand so I don't mess up anything. Also what type of oil does it use?

That was very helpful. Thank you

Beautiful leather

Use this for equipment mowers chain saws power washers if you use gas with with ethanol an store it for awhile you will have a problem

Gay

Great job just spending time with family Sir

It is the same size as other boot brands I am 8. Should i order the same size ?

Another option; czcams.com/video/NhHod7D5YAE/video.html

I recently added a vent to one of my older fuel jugs and they said to use a step drill bit and DO NOT use a regular metal drill bit. I used a regular metal drill bit on one a couple years ago and it did not make a clean square shouldered hole and when vent was inserted it split the seam. When I put the last one in last summer 2023, I used the step bit and it worked great., no splitting. I do have a couple jugs that have the vent on the side in solid plastic away from the seam, so I think in the future I will install the vents, high up on the side of the fuel jug.

I wonder how a small c clamp would work to get that vent in.

Pretty good.😊

Anyone who has ever worked as a handyman will know that this van will never look and stay this organized once you get busy. No matter how hard you try, you always end up throwing 💩 in there, plus don't forget the added benefit of old materials etc that you remove from a clients house, plus any garbage and debris you have to haul away. Your van will only look this good for about a day lol

How well did it work?

Simple all great saws...

very good information!

Kinda funny, my 93 Toyota RV with 3.0 is leaking in the exact same place. I paid mechanic to replace valve cover gaskets, but now it leaks from this spot! I tried to tighten the bolt but did nothing. Its a bad place to leak due to the oil burning off the exhaust right below. Where you able to fix your leak? and do they tend to leak in that area?

love it

AvGas is dry. I ran it in my 67 GTO and the Engine got SUPER HOT, so hot it still was warm in the Morning. also AvGas is a great solvent for cleaning and repacking bearings and brakes leaving no oily residue like Automotive gas. just dont soak your hands in it as it has TEL Tetraethyllead which skin can absorb, get into your blood and into the liver and other soft tissue organs, such as Brains.

the true saying goes.. when all is else Fails. RTFM

Steve says on some saws you can grease the needle bearings in the clutch using that tool.

. . . and the governments don't understand why they are not trusted. It's simple, they are not trustworthy.

Was denn das für ein Vergleich? Beide sägen kommen aus einer Herstellung.

Now you have had this can for a period of time do you still have it or is it with mine in the trash. Interested to here from you.

I am having problems starting my Husky Rider mower. The guy who services it told me it was the ethanol in the fuel and that it damages engines. I'm glad I came across this great video and now have a solution to the problem. Grateful to Kimball Cody for sharing his knowledge and all the posters here. 👍🙌

Nice! I’m starting my Handyman business next month and was looking at bigger cargo vans, but in my budget almost all I’ve seen are rust buckets. Good job! Looks nice and efficient.

Nice! I’m starting my Handyman business next month and was looking at bigger cargo vans, but in my budget almost all I’ve seen are rust buckets. Good job! Looks nice and efficient.