Video

Hi, I recently purchased a Mavic Air 3, but unfortunately, it was involved in an accident within the first 24 hours. The drone was attempted to be flown by friend and crashed into a bus. Fortunately, the camera is undamaged, but the opposite side of camera body is severely crushed. I'm wondering if there's any possibility of repairing it ??

So thankful to find this video jus before replacing my today broken arm.

If the motor runs, used gorilla glue gel , only on areas that broke up Hold 15 sec, let set for a day.

Hello, will it work if I cut the wires and solder them and use heat shrink tube rather than soldering them to the board?

How do you remove top and bottom cover

What size screwdriver is it?

Excellent Video! What is the tiny chipboard glued to the drone frame (at 4:45 and top right in the picture) with a ribbon connected to it? My drone frame broke near the screw post left of the chipboard, and the ribbon detached (or tore). Upon inspection of the ribbon, it doesn't appear that the "wires" in the ribbon actually connected to the chipboard. Could you provide me with some explanation and recommendations about this chipboard and ribbon - what it does and is it fixable? Thank you.

I’m not worried about the freaking dissembling, it’s the fact nobody and I mean NOBODY has had to remove a rear arm. I have a broken REAR arm and it’s not a screw that has it held to the aircraft.

Why not just split the wire ? Is that a bad idea?

You go through this whole video talking about an ESC and not even saying what an ESC is assuming everyone knows. I sure don't.

o meu quebrou a direita trazeira

Great video , ! I got an "accident" today , now I have to order the top shell I think I cand do my self. Thanks yuo so much!

any shortcuts like this for the mini 4 pro?

Need help with replacing rear onstical avoidance sensors

Hello I would like to remove arms and motors from my Mini 2 SE and send the rest to nearly 100K feet aboard a high altitude balloon. Will doing so defeat the control, recording or transmission capabilities?

There were clips (male, I think) on the replacement motors but not on the tello, so you cut the clips off. What if I wanted to place female clips on the tello to connect the new motor to, so I didn't have to mess with soldering. Would that be possible? Sorry if this is a dumb question.

Hi. Are the arms identical, meaning that can I replace in example left front arm from mini2 to mini, without replacing the motors? Seems that finding new arm for mini is way more difficult than to mini 2, so are they 100% compatible (just arms), without the motors. (as I have just broken arm, motor is fine)..

Did this repair to replace the rear right arm. Now im getting ESC errors on 3 and 4. I could understand one of them being rom me screwing up the repair, but im perplexed how it could be both. Any ideas on what I could've done wrong?

what is screwdriver size required to open mini2 body

sorry you lost me when your picture wouldn't focus.

Crashed my drone last night and I thought this might be something that I would try working on myself. However after watching this video I realized that this is WAY OVER MY HEAD😂😂😂😂 To the repair shop I go 👍🏾

I love it bro.... I just got the mini 2 and of course, crashed it..... the top cover got a nice puckture-type crack in it. so it's still working just ugly. I'd like to fix it..... Is there a manual? Looks like the screws are hidden everywhere. I'm researching, before I go into it. whadya think?

Do you have a tutorial on how to put it all back together?

Question- Since the wire are exposed, can you just cut them midway and solder them together with the new one instead?

Hi Jack, nice video. Can I ask what size phillips screwdriver have you used?

What size screw driver to remove axle screws front arm ?

Hi, too much hazzle, too much risk of damaging something. Just cut the old wire midway and cut/solder the new ones accordingly and use some heatshrink/tape. Regards

If you replace the motor do you need to re calibrate with software?

Im unable to start my drone.. plz help

nggambleh.. ra repair kok

Great video! A motor on mine is hard to move. I Want to put a new arm on it. How much is it to have it fixed and where do I get it done?

Hello brother do you help me by repair my DJI mini 3 drone

Hi, is it possible to get 5V 1A from inside to a very specific outside camera? If possible, where exactly? thanks

Esse é o "Mini 3 pro". Esse procedimento funciona com o "Mini 3"?

i wont even spend 5 min. Just cut old wires under the "hood" and solder from there. easy and you dont have to mess up everything

Top shell replacement the right way? Rips off top cover

Se o amigo colocar uma gota de álcool sobre a cola, irá soltar mais fácil. De preferência álcool isopropílico.

Hey, whats the size of the 2 black screws on each side underneath of the rear arms? I need to find a replacement screw at some point as I wore one of them out trying to tighten it a bit more...

I have a DJI Phantom 4 Pro + . I live in Oregon but was born in Jersey. My gimbal keeps moving left to right and right to left on its own while making a squeaking noise. I calibrated the IMU, the compass, and the camera and it won't stop moving by itself when the drone is powered on. Can you please help me?

How much is a new shell ?

What do you think about cutting and soldering wire inside the leg? The leg can be disassembled with a heat gun, as is the case here: czcams.com/users/shorts4nYqPfRGUTk

Have done it? Seems like the original glue are still there.

So since your top panel was broken the video didn't really show me how to remove it in needing to remove mine to repair my gimbal and I've got all the screws out and basically impossible to get off almost seems you have to tear the top up to get it off and just order another one cause it's so thin and def doesn't remove easily almost seems as if there's a glue around the whole cover ?

Anyone know what size torx you need for the arms?

What are the size of the fuselage screws?

Quick question while removing the bottom cover I ripped the antenna strip Is there any way to order this part..... I've looked everywhere and can't seem to figure out what it's for I did pull it away from the shell on the other side but apparently the one side was still stuck enough that when I got the tabs for the bottom shell to come loose and lift up it ripped the little ribbon .....

What kind of philips you need?

Excellent demonstration. Thank you!

Nice flying, do u guys at drone zone have open flying events for freestyle?

Dude.. this is WAY too complex! Good thing I signed up for the repair package cause my arm broke after letting my father in law fly it.. he hit a palm tree 400 meters high. Was surprised only the arm broke but still. I bought a spare arm thinking I could do this myself.. I’ve replaced iPhone and iPad screens.. but this looks like too much.