Video

What’s kinda glue that is

@1:49 I received the same instruction from Josh @ DK bikes to adjust my recent purchase, an introductory 24" cruiser BMX, which came with this issue. 1st time I had seen something like this.

Will this still work if I change the 170mm to 175mm

how much did that dropper cost?

My SE Big Flyer is acting up and this kinda helped..bike life !

I mean, just don’t change anything and stay in the middle chainring? Not changing the cassette means it virtually pointless!

Why did you need to loosen the crank first?

Will this work on a trek marlin 4?

Cool video bro. I will perform this quick fix on my son's Mustang 2001 soon.

Did you shorten the chain at all?

transmission fluid interesting

i have the exact same bike

Would i be able to run a 32t with that crank set?

I would definitely try to go with a flat-bar that's the same width as you're shoulders for the most comfortable arm position. That's unless you intend on hitting the mountain bike trails👍 What's more: Wide handlebars make filtering through traffic extremely difficult.

Ok so on the 9th spoke which you said was going in the hole to the left of the first spoke and you ended up not going in the hole specified with no explanation why?

What are you going to do with the contaminated soil when you are done with using it?

So I’ve done this a few weeks ago and it’s best using brake outer for the outer cable and works spot on

Won’t your sprocket get loose?

So pull any two. Find the tight spot. Keep it there. Squeeze it. Tighten two. Than put in other two and star pattern?

So how did you dish it

I tear mine apart and remove the innards and clean before overhauling. They left the factory with grease, and that is the best way to fix them. Also you get to check for worn parts and replace as needed. I have many parts for these as I have been overhauling them for years.

What about routing it around the bb and up the seat tube

Great technique! My chain is almost perfect. Thanks!

cant i just change the sprocket?

How about on one piece cranks?

I have same bike and looking to upgrade my gears glad it a 10 would fit

Sorry but a 3 or 2x8 to a 1x8 give and awful gear ration especially for climbing this is more workable if it was a x9.

Can you pls help me with my bmx pls

Hey will this work on 2021 trek marlin 6?

Thanks. My daughter's BMX race bike has dropped chain in 2 races and i have felt hopeless. Will try this out.

How is the riding?

Thanks for this!! I had to take my chainring off completely and look at it from a side angle. A bunch of little bends needed to be adjusted and everything is sooooooo much better now! Appreciate it!

Thanks man! Kept realigning the rear wheel 😅

Thanks for this video. What a great and EZ fix.

you can drill rivets ,or use plyers for rivets just simply leave on middle chain ring it will cost you some time and 0$ until you save some money for beter parts (for me this is just hobby )

Doesn't leave a chance for me. I recently fix sprocket on my niece's BMX thinking it might be the problem because of age. Then this same problem arise after I installed the new one. It would be harder for me to to this because I have a One Piece crank which only have a single nut that hold the chain ring in place. Still looking for answer. Thank You for this video this will help me a lot.

Drilled 2 holes in the back at the bottom of the seat tube with 1/4 inch drill bits centers 7/16 inch apart filed it down to an oval and stuck a salsa rubber grommet on my 2010 stumpy frame. It looks like it was always meant to be there. Just put a couple of zip ties on the bottom of the frame to neatly tie it to the other cables under the down tube.

Thank you THANK YOU for this video haha, i finally got the solution 🤝

A huge Trek fail. I own a 2021 Marlin 7 and my advice is to avoid this line of bikes. Too many other bikes offer much better options at a similar price point.

So I've bought 2 different chains and 3 different sprokets and it's the same. some times it's worse or a bit better no matter what I do. I don't fucking get it I've built dozens of bikes I own almost 30 bikes all are fine but my one bike I use for street riding.

Killer video for those who know. Very cool and thanks 😎👍🏻

I wish Ford had come up with a better design especially since these Mustang windows are under a lot of stress by not having a full door to surround the top of the window. Great video, I’ll be sure to use this trick when I re-glue the driver window on my 2000 GT

Best type of bike there is.

You could take the sprocket off to see if it needs a hat washer on it

Hub is on eBay now with a current bid of $352

He doesn’t look comfortable enough on the bike in my opinion maybe he just looks like he rides too stiff

Good video but can barely hear your lacing instructions over the music...video would be 100x better without it.

Does it require seperare brake n shifter cable or same cable will worl?

😃 Great Idea, THX

This was only a video on how to remove a star nut. Based on this video the stem lock just magically appears once you remove the star nut! You don't even need to remove the front wheel! I has hoping to see how the stem lock installs and what it looks like on the underside.