Video

My bad Typo! 1969 😎

Exactly what we are doing

💯

Picks square bales and lifts them on the deck of a trailer or truck

😂😂

Yes you are on the money

Yep Square bale picker

😂😂😂

Seen one on Facebook marketplace for cheap the other day. 100$. I think I paid 400 for intake rails and injectors

Stock

I was told a 2004 suburban

Yes. I’ll do a video of pulling it apart and gapping rings and assembling with a Low Buck Truck Cam from Richard Holdner. Among other upgrades

Me too! Every drive I’m grinning ear to ear

Right! Come onnnnn

Thanks! Hell yeah!

Technically if you pound the bearing in or use a plug. You don’t have to. But it just cleans up the looks

It is together and running but trans went. So swapping it tomorrow hopefully

@@bickfordcustoms what transmission? I'm debating on using original or the 4l60e that came with the engine.

@adamcabrigo 700r4

I’m sure it could

Yes it is

Heck yeah!

Thanks! Yeah day show was wasn’t as good. But evening show was way better.

Truck did not break down

@richardortiz8704 dang right

Warden Chevrolet broke down Ford and Chevrolet broke down 👎👎👎👎

It coulda been idling

@@Whiteout69 he really doesn’t know cars if he doesn’t know that they stay at about 1000 to 1,500 rpm when idle, I mean come on

Very soon! Been a busy week, so haven’t got much done

Yes

Thanks!

Thanks fella!

I made a hawks custom torque arm work! I got a video of it on my channel.

@@bickfordcustoms I've dealt with them Torque arms enough in the past, I don't like them, they limit what you can stick under the car. I remember I had Monza and Vegas in 75 and up they all had them Torque arms. Had a IROC-Z had that junk set up in it, I blame General Motors they did this so back in the day you would buy the Dana 44 from Chevrolet Performance shop. They put a V6 rear end behind these Camaros. I had a 1977 Z28 Camaro with leaf springs, with the 8.5 and 30 spline rear. They just don't make them like they used to. Have a good night.

@jorgedacosta8957 yeah I get ya! It is a tight fit in the tunnel. I did a little massaging to make room! But this are is a little bit shorter so it fits behind the 4l80e. For now it’ll work

@@bickfordcustoms I totally understand and you have to do what needs to be done, but I know for sure you ain't going to run that wimpy 7.5 rear end. Good luck with the project and thanks a million for posting the video, I loved your swap.

@jorgedacosta8957 yeah I’m switching to a quick 9” which is able to bolt up to the hawks kit I bought. Thanks!

Sure am. If you can’t tell by the voice in the video lol

5.3 ls

Yeah it has a check valve but it’ll get deleted soon

Hopefully it works well!

What cable do you not have?

​@@bickfordcustoms the USB cable to actually pull up the tune on computer see it the other day when I got on it seems to lower the demand when I'm at full throttle line pressure gauge went two 0% and turned yellow on a highway pull I was told line pressure is 0% is 100psi

@Kingcadillac816 I’ll have to look at that

Someday I’ll I’ll get to it again

Again.

Yeah I spent time working on it then put it in storage. I’ll pull it back out this winter

Thanks! Should be pretty fun!

😂😂😂

Definitely would

Thanks! I gotta keep the hood… sleeper mode ya know haha

Thanks

1970.5 Camaro split bumper

Lots of welds

Thanks for following along

Not much at all. Exhaust was close to frame but all bolt in parts

@@bickfordcustoms really? Did the gauges work?

@moejr14 yes with the right sensors

Nice! I shouldn’t have that issue since my exhaust will head out my fender! Haha

@@bickfordcustoms yup I heard you mention turbo and pipes so I figured as well Right on man!!!!

@vandettabuilds6641 hopefully next video I’ll be getting it built

@@bickfordcustoms it's cool. I'll be watching I take mine to Archie's automotive in Murray tomorrow. It's my son in laws shop. I'm putting my Camaro on a lift so just can look at everything for my own peace of mind!! Ha ha ha

Always handy to use a lift!

Thanks! Yes it definitely will be. The other one was cracking so it was due for an upgrade

Ohhhh yeah! Hopefully get some time in the shop fabricating this weekend

Hell yes