Video

No, it's not, but it's fine.

Did you ever find anymore videos of the rendering being done?

Hello sorry for the delayed response to this, we do have two models available, do you want to pop your email address over and I can send you some information? It's Leoni.thompson@schiedel.com. Thanks Leoni

IDIOT

Hi. Sorry for the late reply as we didn't see the notification for this. Ventilation is critical in this aspect to stop any overheating near combustible areas. Also, for first floors, designers tend to create a column wall around the pipe for safety reasons, so any noise from below isn't heard

Michael, where do I put the vermiculite - on top of the closure plate? If so, to what depth? Or do I just pour a LOT of it down the outside of the liner from the chimney top? Thanks.

@@jimskirtt5717 How are you Jim? First you need to ensure that the base is well sealed with a neatly cut steel plate so the vermiculite doesn't pour onto the floor, then head up top to the chimney top and I normally cut a hole out of the base of a large bucket of plastic tub. The hole will be slightly bigger than your new steel flue liner but not larger than the old flue. Then tape the top of the new liner and pour the vermiculite into the tub. That will guide the vermiculite into the gap between your new steel liner and the old flue. It could take a few bags in large chimneys

@@michealbreathnach2928 Many thanks for that, Michael. Much appreciated.

Hi Robert, apologies for the delay. Unfortunately this is not currently available in the USA, I believe this is something to do with a difference in the regulations.

@@SchiedelUnitedKingdom thank you for your reply

I've read on another document of schiedel leca is used, but also I think they don't want to promote a cheap solution

Hi. This is only part of the production line. We have a combination of manual and automation. Our Weil Flexistar machine automates a lot of the procedure. czcams.com/video/yFz3Jr3Ea38/video.html

Hi. You should be able to retrofit an insert. A standard stove is freestanding under the chimney breast, so if the insert stove is fixed correctly then why not? :)

Bad idea.

Instablaster...

Hi. Sorry for the delay in replying, the main reason is that the heat from the top of the stove / furnace is too much and would melt or damage the flexible liner. For this reason, you always have a starting pipe and adaptor which is rigid.

@@SchiedelUnitedKingdom even stainless?t316?

Hi. According to our Installation Instructions: "The connection to the appliance should be made using fire cement/rope or high temperature sealant to ensure a positive seal. Where TecnoFlex Plus is to be fitted to the top of an open fire place, a Schiedel Rite-Vent gather unit should be fitted into the throat of the chimney connected to the TecnoFlex Plus and sealed off. When connecting Triplelock flex to a Schiedel Rite-Vent flue box, the flexible liner simply pushes directly on to the fast fix spigot. No sealant is required. When making a connection to a fluepipe in another product type, such as rigid stainless steel single or double wall or vitreous enamel, then the appropriate Schiedel approved connector to/from flexible should be used. The connector should be suitably sealed to the appliance spigot ensuring a gas tight joint." There are more details in our various Installation Instructions - www.schiedel.com/uk/chimney-and-flue-installation-instructions/

Thank you for that info buddy 😀😎

Hi. Sorry for the late reply. It's preferable for an angle due to the draw, like you mentioned, but in our Installation Guide, on Page 6, you can see some examples at 90 degrees. We also have a document showing acceptable alternative connection methods. Both Installation Guide and Alternative Connection can be found here: www.schiedel.com/uk/products/steel-system-chimneys/icid/ - If you visit the page and scroll down, you will see Alternative and also Downloads.

Oh dear! Which chimney was installed?

Nothing as sophisticated as yours just plain single sheet ducting. I have painted it to camouflage it. Next one will be yours. Thanks for replying

@@SchiedelUnitedKingdom where can I get one those angled wye tees in America?

Hi, Mr Zoo :) The ceramic liners are not glazed but are frost proofed. Regarding the cost per flue liner, 160mm I/d 7.75 euro per piece. 180mm I/d 8.45 euro per piece. 200mm 1/d 9.15 euro per piece. Give the Northern Ireland office a call on Tel: +44 1202 861650 for more details, or drop them an email here www.schiedel.com/uk/contact/ for any more info.