Video

Great video. If you make the title say transmission removal and torque converter replacement it may help a lot more people. I would have loved to find this when I was removing a transmission here. Great work!

I'm finding more and more that Nissan makes terrible cars

SBC Hamburger 1099 oil pan EBay

That seem pretty simple, I'm a person who needs to see stuff done first or i will be spending more time then needed, this looks like an easy fix, ordering now

Having the same problem now with my Chrysler 2005 3.5 the serpentine belt keeps slipping off the tensioner and bouncing off the harmonic balancer. Put a whole new tensioner, was fine and now it’s back to moving and bouncing off the balancer again causing the belt to slip off. Went through 2 belts already, can send you a video just looking for another opinion.

Where did you end up finding the correct torque converter?

do you have to remove the timing cover to remove the head? Can you release the tenision of the timing chain from above with a tool?

Cat 🐈 mode c crawl slow 🦥 for the 🌧️

Nice video. Both items at harbor freight -$165. No way you’re doing it for $30

Great video Perfect

State Farm is shady!!!🤬

Paid $400 for mine , took a 350 engine and 350 Turbo trans out of my 78 Silverado , traded for new headers , motor mounts $30 , Tach $40 , New Universal joints $50 , 1998 S-10 Still have a few things to buy but nothing expensive , I won't even have a grand in everything

Put some duct tape on it

This trucks suck

Is don’t get it. Too rusty?

It's that a pather platform car

I like this... Thanks for bringing this to my attention

This was a fantastic video. I ended up pulling the boot off the old coil pack and shoving it in there to fish out the spark plug.

I reset the key fob settings to default and it worked on my 2020 civic

nothing beats honda ! awesome bike

How much is a?How much is that most cycle right there

I'm trying to swap out my radiator, 79 J10, but how do you remove the trans cooling lines at the bottom of the radiator? Mine just wanna twist up and the side of the hoses towards the tranny seem to be press fit. That side does have a hex fitting but I'm afraid to mess up the lines.

Would you provide Amazon link to the camera you purchased? Thanks!

As far as parts and sensors are you just using 350 parts

Thank you! I just got the truck yesterday and am happy to see this will be such an easy install. In the middle of moving so I will need to do this after I get to my new address.

Oh man. An ode hose. Why didn't I think of that?

ive been driving mine with no power steering for a few weeks and my arms are massive now

I have been trying to figure this out for the whole year I have owned my used 2017 Honda CRV.. and just a quick minute after watching your video it is finally working! THANK YOU so much! Now I can enjoy a cooled off car 😊❤

Great job on fab.

You skipped over the entire part im worried most about (the timing disassemble)🤦‍♂️

Does the aftermarket camera still turns along the steering wheel while reversing?

Just about finished installing mine when I noticed there was only 3 oxygen sensor holes so thanks for clearing that up. I noticed that my steering shaft nut and bolt at 5:21 are touching so I'll have to grind off the extra 5/16'' of threads and one of my spark plugs are touching the header 'heat tape' and it may melt the rubber and I'll need to get gaskets and wire extensions Thanks for the help !

What’s the tool

Oop I heard that 10mm wrench fall into the underworld. You'll never see it again. But good video man. Helped me a ton

it could just be from up north, the salt used on northern roads does a number on any steel components regardless of the vehicle.

Omfgggg this is me today !!!! 😔

This is a very intuitive showcase. Well done!

HI!!2012 Honda Odyssey shorted the positive wire of the generator, the car does not start, what is the reason?

take the cab bolts out and lft the cad up off the rails and put a 4x4 wood block so you have room you need. Oh" and don't forget to cut the firewall flang out and why are you leaving the fenders on they will get a thrashing if you don't take them off.

I can’t get mine to set in the sensor. What am I doing wrong

Did you have to make any changes to the driveshaft? @Bentoaksgarage

good video thanks

Is there any updates on doing cold side

not sure that I'd have used a 1" impact to remove the head bolts. you want to get a long T-55 like the 3 " ones from Mac tools ($61.00) a 24 inch swing arm with a 24 inch snipe. Then the bolts come loose. they snap 3 or 4 times while the bolt twists 1/4 turn then POW bolt comes loose. All the impact is doing is twisting the bolt back and forth.

You really like the word garbage..know many people who own these and they never have had a issue,,only thing i agree with you on is the rear tire,,it does look cool but no matter what bike it affects the ride..my m109 has a big tire and it looks bad ass but is very hard to corner

Would it just be better to buy the motor instead of fixing the gaskets? My Dodge Journery has the same problem but everyone says to just buy a new motor.

On a 2007 Honda Odyssey how do I get contiuos power

😅😅😅

Thank you for this video I have a 2016 judge journey with the same problem I just can't seem to get anybody to do the work for me here in Palm Beach County Florida I'm trying to be all over 5 grand For a new motor.

I have to pull the engine and this helped me do some recon for the job. Thanks! Liked and subscribed. Nice clear and to the point