Video

ah...would we rather crash into dry land or into water...well on dry land i guess we all agree there will be damage but in water i guess if you disconnect the battery quickly and dry the electronic mechanisms out you might get lucky....i guess u could drown geting to the model if u were not carefull wheras on land you walk up to your heli remains and collect it in a bag or your jumper.

Hi Colin, my name is Jeff George. I saw your for-sale post on the BBF forum. Is this model still for sale?

I have a zx6r and it making a clanking sounds only in 2nd gear when I get on the gas but if I pull the clutch in and rev you don’t hear it and it’s only in 2nd gear I have it on my page to

I remember this was the coolest quad ever when it first released

Very cool. If i use a radiomaster 16tx can i use the conventional receiver in the app? Any suggestion?

Oi amigo me dê uma informação como e fasso pra enroscar as artes preta nós links que vai no servo está entrando torto e o cabo do esc está curto pra levar até o receptor

Hi ,own zx6r 08 ,cluth is not slipping and is changing good but after getting hot a whistle noise came from clutch when the clutch is pressed,need to change the clutch?

Which of the Unilight did you install? I see so many options. Thanks

Hey Colin, have a question about your canopy, did you smoke spray it from the inside?

One of the better chain videos but 1¾ inch chain slack is the largest amount ive ever heard of on a road bike. My FZ8N says 25 to 30mm or about 1 inch.

Why go through the hassle of measuring them? Why not just replace all the plates

This is a great video on this topic

whatever happened with part 2?

I’m sorry why not just replace everything and not be cheap pay once cry once and not have to take it apart every time

Hey i got a question from an old video. Do you remember where you got that carbon fiber swingarm from the chain tension video?

whered you get that swingarm?

Were you trying to crash the heli?

Thanks for video I was able to adjust chain myself

That was so awesome!

Sick flying dude! Seems like you're enjoying the M4 :)

Mentioned nothin about needing a torque wrench Not listed in your tools👎🏽

Good grief folks. TORQ SPECS are indentified in YOUR Service Manual. Each bike is different. While some specs will be the same, many are not. And if you can't afford a $120 (or less) Service Manual, at least get off your lazy ass and go down to your dealer and request a Torq Spec printout!!

If you are removing the front wheel, why the heck would you rest the calipers on top of the wheel? That makes no sense at all. Get some bungee cords and suspend the calipers from your handlebars or some other secured point. Not the wheel.

"promo sm"

When I loosened up the left 2 screws oil started to drip from the fork, why is that

Unbelievable how those things stay together under all that stress. I’m stressed just watching it! 🤣🤣🤣 Amazing control. So, the helicopter can do basically whatever pops into your mind, eh? Cheers, John

You are the best

Is there any certain orientation that clutch hubs needs to be reinstalled?

Thanks for the video, helped on my own racebike

I bought a 04 zx-6r, drove great and shifted good for the first couple rides till one I turned it off and went to first gear with the clutch and it just died, I can see the clutch moving in the casing but it still dies and when the bike is off there is still some resistance to movement with the clutch lever fully engaged. Not sure what could be the issue or what's causing it not to fully disengage the clutch? Your help would be great.

Your video is a little better than most that I've seen I'm a beginner to motor bikes but I've spent over 30 years working on hot rods so far your video is the best

What break in time and top speed or rpm can go after get new clutch I was told 6 rpm and 500 miles ... maybe thats wrong or maybe it doesn't matter ? Sucks driving slow maybe some one has better info then what I was told or if some one can confirm it is just what it is. 2022 zx10r

Your video is well appreciated my guy Thanks

what are you currently doing in rc these days? are you still competing or just causal ! you are an amazing pilot just haven’t seen much

I just picked one up on sale at Great Hobbies 80 bucks off.

Does it matter where the friction plates are inserted? I noticed there a divet on each one and you put them on the gear in different orientations.

Definitely incredible video. Extremely helpful!!

I took me about 10 ft of wire and screw ups to get a decent result, don't get discouraged if you mess up... A lot lol. Biggest help from this video was the manual twist to sink that wire closer to the bolt head, thanks!

☠BLACK BARON☠ 7:35 It's not easy to unmount this stuff in scale helicopters (600-800size) to check and exchange plastic gears and ball bearings if it starts making strange noises.

Did you ever actually mess with the chain tightening in this vid or did I miss that.

Colin still got it!! Sexy..

My clutch cable broke I was able to get a replacement, wasn’t the same one I had but it works, now my bike won’t speed passed 60-70mph it just redlines if I full throttle even if I shift it up to 6th gear it doesn’t want to go passed 60mph, can it be cause of my clutch? I know before I was having issues getting my bike into gear when I try an do a pull. It like slips

Great advice- Thankyou 👍

Rigth to the point!!! Thanks a lot

Hi Colin watching you from Portugal. Great Video. Bought an accidented (small) ZX6R with 50KKm couldnt engage the clutch and after moving ajusting cable screws plus pressing several times the cluch lever it worked. While riding the bike when i wanted to acelarate fast it would increase rpms but not the speed. Slipping I guess. Next day clutch had a litle course, bike would start moving slowly and, after some tries, I could engage 1st gear but releasing the lever the bike would not move even when accelerating. Any advice, would you say this is a clutch problem? Cheers and keep up with your great videos.

Awesome flight you got skills.❤️

** note to viewers, do not use a punch to hammer down your bearing

Ineed help finding the clutch kit for a good price

Thank you