Video

Very good explanation and video!! Thank you so much!

Per the service guide, before installing 2nd bolt on Driver Side, the oil pan bolt in the bolt hole located between the torque converter clutch on and U/D clutch pressure tap circuits, it will be necessary to replentish the sealing patch on the bolt using Mopar Lock & Seal Adhesive. Here you can use Loctite Threadlocker Blue or Permatex Medium Strength Threadlocker Blue.

Great video. Good job!

What socket for the oil drain

Thank you for sharing this amigo it helps me out 🙏

Excellent video

Give er the ol size 12.

Thanks

do you have to pull the rear to get the front of the shaft loose?

4.4 qrts with filter

God damnit. There goes Saturday...

I wonder if you can run Rotella T6 5W 40 in the engine

Always change your transmission fluid and a little filter under the battery change your timing, chain or belt 5000 miles early and run iridium plugs if they last over 100,000 miles they look difficult to get to

JEEP, WHY DON'T YOU FIT DRAIN PLUGS ?

Question, how do you lineup the new one if you don’t have marks on it

I ordered the retainer clips on amazon and they look similar, but they dont have the two tabs to lock into the fender flare. Can you post the link to The retainer clips you bought?

What size washer do I need to replace the old one on the oil drain screw ?

how is the bigger piece at the front calle and where can i buy ti ?

Thanks for the helpful video. Early liberty's with 45RFE trans (2002, early 2003) have a different type filter (metal) and o ring, it is enclosed in a metal base that must be tapped into valve body without distorting it, most people use seal driver or socket that matches outside diameter to insert it, lube it with fluid, be sure to remove old one first, just a heads up.

Thank you so much. I appreciate your help.

Currently using Honda ATF Dw1, can I do drain and fill method (top up Amsoil ATF), would there be no problem at all?

Buona sera. Fate attenzione nel vedere alcuni video. In questo differenziale la jeep raccomanda esplicitamente il mopar e bisogna aggiungere 118 ml di additivo specifico. Alcuni tipi di olio la jeep li sconsiglia drasticamente

Thank you for the detailed instructions. I'm wondering about the rotating torque required for the pinion nut. The 2005 Jeep KJ Service Manual says "Rotating torque should be equal to the reading recorded during removal plus an additional 0.56 N·m (5 in. lbs.)." Are you recommending 10 in. lbs.?

Nice, clear pix of everything with clear instructions. Thank you.

Amsoil superior 2 hondas oil?

How many quarts of transmission fluid does it needs after doing service? Jeep liberty 2005 4x4

Hello, I’m gearing up to do this job on my daughters 06 Jeep liberty. I was looking at the rebuild kits versus a new driveshaft as it’s just a ripped boot for now but not sure about those kits. Anyway, looks like this video is about a year old what brand did you buy and how is it holding up? Thanks

Thank you. I’m a woman at the pick your part yard and was able to follow your instructions to remove the fender flares. Now I’m just going to use them to reattach.

How much for that driveshaft

Nice video! Thank you!!! What kind seal grease or lubricant did you use on flange?

Great video, thank you

Is there a reason why the front diff cover wasn't taken off like the rear?

I am doing mine tomorrow. I decided to go with Valvoline Max Life full synthetic... mainly due to it being on sale. Looks easy enough.

Is this with or without replacing the crush sleeve because I’m not getting near that torque reading. If I go over 100 it feels like it gets hard to turn and feels like it catches. Also takes 30 in/lbs to move

How many litters atf capacity of honda fit

Doesn't hurt to wear safety glasses and breathe through your nose doing this of work.

It would’ve been nice if you heard of told us the size of bit to use to remove bolts

Thank you for posting this. Mine on the passenger side fell off at some point. Showing the part number really helped to make sure I ordered the right part. It snapped on so easy. Even someone who is terrible at working on cars (me) can install this piece.

Always take the fill plug out first because if you pull the drain plug first your screwed if ya can’t get the fill plug out.

It was a big help since I'm going to be replacing a broken wheel stud and doing both the E-brake, and rear brakes while I have this whole thing apart.

im having a horrible time with this project. i replaced.the wheel seal and put back together and now i have a bad grinding noise coming from somewhere

I changed my transsinmissin fluid every 7or 8K. Because the color change earlier.

Wow such a amazing video . So much details. Can you make a video for liberty for front main seal and rear main seal. Most people who owns liberty have a problem of engine oil disappear slowly.

It’s a amazing video with so in-depth details . Love the kindergarten comment. I learned so much from this video . Hope to work on my 05 liberty. Thank you

hello, great vid! have this type jeep kj axle inner seals ? thx 😅

Thank you !

Saludos cordiales desde Venezuela yo tengo una jeep liberty kj SPORT

Stupid question, but do I turn the bolt right to loose it

She gettin all 4 qts. Lets be honest here

Amsoil diesel oil has even more anti wear properties (zinc) than this oil. Comes in different weights as well.