Video

It only has four clicks and I think the starting point is one ! And it says on line top and bottom need to be set the same !

For me two clicks top and bottom on both shocks is the best for me ! I ride solo and weigh 210 ! Great video Mike !

Just added this to my 2024 Rogue Sixty ! Looks amazing !

✨🏍 Rench Ranch, THANK YOU VERY MUCH SIR! You are a Pay Attention to Detail Man, and You Speak very clearly! I have watched other videos for this Process and in my humble opinion Your Video is Great! I will follow Your Procedure, I also have my Owners Manual which is Highly Recommended and I do my due diligence to Strictly Pay Attention to The Details; after all, The Bike Cost me A Lot of money and I will be keeping it and Riding it for a long time! I have personally run into people who have used a Torque Wrench to Specs and the result was not favorable. I also have discovered That All Torque Wrenches are not set at exact proper torque, so we need to make sure that the Torque Wrench is in Proper Spec. They can become inaccurate with Use and need to be Re-Calibrated from time to time! Anyway, this is not Rocket Science and Common Sense is very useful! So, Thank You Very Much for a Great and Informative Detailed Video! Enjoy The Ride! ✨🏍💯%.

I need these mods!!!

I don't know if you still check these comments but I'm trying to figure out about replacing these paper gaskets. I thought they would have came with an adhesive side. What did you put on there to hold the gasket?

👍

Please don't recommend anyone go from 2016 stock shocks to 2018 stock shocks. I tried this and it was so much worse! I am throwing in the towel of trying to make things better on a budget and am going with a set of fox shocks at 1k cost! I paid close to $200 for the 2018 stock shocks and it was a total waste of money.

What size oil filter wrench is needed (mm)? I couldn’t get the old filter off by hand.

Все круто, гаики то внутрь надо бы колпачковые же поставить, а то вещи будут рваться об болты

hello, thanks for the video. The back of my Twenty Bobber squeaks when it bounces. I removed the springs/shock absorbers and oiled/greased the bearings. no idea. Can you give me a tip. It's loud and you can hear it while driving.

Thanks for the tutorial, Mike!! Very detail oriented. --- Your Scout is looking really sharp for a 2016 model.

Hi I have the same speed four but green i was on my way home and check engine light came on but the bike runs fine any idea what it could be ?

Do I need to take both drain plugs out? If I don't what will happen?

Than is for making this video however unfortunately I believe you are checking your oil incorrectly. You do not screw the dipstick in to check the level…..check your book or search CZcams and watch a dealer video.

The settings are just a starting point. Ride the bike and try changing the settings to see what fits you the best.

Hi Mike, I nearly always use an extension bar on sockets as I like to keep my hands well clear of hard bits. Don't like wasting time cursing and bleeding. 😉

Hello Mr Rench! Great seeing you working on your Indian. I can't get enough of your videos! 🇵🇹 & 🇪🇸

Glad your back to the Scout. Been watching your channel for a while and I love what you have done with the bike. Also I have found your videos to be very informative. Keep up the good work!

Man i didnt see you were back doing video on your indian. Make my day. Cheers

Nice easy upgrade for your biking pleasure :) My wife's previous car registration started with BJ as well, guess what sort of job we called the car.

Thank you Mike!

Thanks for the video, great help for my own tacho installation. Question, I noticed you have a black cover on the 2 bolts of your luggage rack behind the seat. Where did you get this? Really looks neat!

You know I just did this, and starter chain guide is now rubbing, can’t figure out why. Not any videos of reassembly

Where did you get your mirrors? Thanks!

This is not about your video but do you know how to tight the 2 hex screws (1 next to the oil filter its easy) , but the other one is next to the starter and it’s giving me a hard time to get to , I haven’t been able to find a source that helps me thanks.

15lbs of torque is not strong at all. Just to give you idea, Jeep oil filter cover is plastic and is tighten on 18lbs. You freaking out for no reason. Anyway, great video

Looks great. The main thing to remember is to do what looks right to the eye. You can measure and figure for hours only to find out something doesn't look right. Just fun watching you work on this old bike knowing you aren't trying to build some high dollar bike. When you are done you will enjoy it and I'm sure you will get many compliments on it and you can proudly say you did it all yourself. As always I will look forward to your next chapter.

В поряде!!!

I sorted out the Synco Wireless Lav Mic gain issue today. Future videos won't have the static / clipping issue. The manual is translated from Chinese and it isn't clear about the gain adjustment vs attenuation. Seems the default setting is +15dB of volume gain (not adding attenuation). So between adjusting the gain (not padding or att) and changing the settings for manual input volume gain on my Sony video cam, I have fixed this issue. Sorry for the static sounding audio, hopefully it's not that annoying. Cheers! Mike & Melly

Everybody from the day they are born has to start learning. Well done for teaching yourself these skills, and most of all, it is just down to practice and perseverance.

Great video, super interesting. There's a lot to learn here. Keep the videos coming, Mr Rench

Great video.! Supermagnas are special bikes for sure. I've owned mine, a 100 % original 1988, since 2011, and I've had no issues with it so far. Honda really know how to make quality bikes...

Welcome back, missed you guys :)

Nice job Mike. Like they say a grinder and some paint will make a welder what he ain't. Really any project depends on how much time and patience you have. There are a thousand ways to do something. Just do what makes you happy. I think this job turned out great. I just like seeing what other people are doing with their bikes no matter what they are working on.

Every time I have to remove the tank I have the hardest time getting the gas line disconnected. Kills my finger tips pushing those tabs in.

Rock on 🙂 Season's greetings

Merry Christmas to Mikr and Melly.

Nice!!! Feliz Natal, Mike e Melly! Your unconditional friends (and fans!) Alex and Lola

Merry Christmas

Merry Christmas to you!

Nice work. Only difference between the average guy and the professional most of the time is the professional will do a job in an hour that the average guy does in ten hours. I would spend a few dollars at Lowe's or Amazon and get a carbide tip scribe. Worth the $8-$10 just for the extra length. Looking forward to more on this bike. Can't believe I want to see a Rebel build, but the stuff you are doing applies to any bike build. Plus what else am I going to do this winter.

Hola Mike! Get Melly's bike ready and rolling!❤

Weres the radiator sensor in speedfour

Excellent!!!

Great video and much appreciated 👍👍👍

Great tutorial! I just bought a brand new scout rogue and getting ready to do my first oil change, and this looks like it'll be fun and I'll save a bunch of time and money.

Why did you have the hacksaw handle, under the bike?

Thanks for the vid been searching for this repair I got same problem with my rebel doyou have list of the items you use like what rtv to use etc

CUTE.... a flat tracker.. almost looking like 1950 Triumph 6T