- 144
- 104 513
Miki2T
Registrace 1. 08. 2010
Video
schaublin 33cnc frézovanie nozovej hlavy
zhlédnutí 90Před 4 měsíci
schaublin 33cnc frézovanie nozovej hlavy
Dream Land _ Žiarska dolina
zhlédnutí 196Před rokem
Keď ešte veľa ľudí spí, dvaja spolužiaci sú už hore, fakt hore.
CNC milling forkardt jaws 90° profile 3/32" pitch
zhlédnutí 87Před 5 lety
CNC milling forkardt jaws 90° profile 3/32" pitch
Very cool machine! Reminds me of a dmg dmu60p
Ahoj, prosim ta vies preco sa z Novej Bane uz nelieta od 2015 roku? Aspon tak to vidno na xconteste..
Ahoj, z viacerých dôvodov, žiadni piloti v okolí, nevhodné terén vietor často ovplyvňuje údolie a je to tam veľmi zarastené , stromy v predu sú vysoké a tiež to miesto pre štart ten násyp je príliš rovný takže v slabom vetre ťažko odštartovať. A hlavne na JV sa nájdu v okolí lepšie terény.
@@Miki2Tahoj, som zaciatocnik zo Zvolena, kde by si odporucil nieco vhodne?
@@33joee Donovaly, Slopovo....
i dont think your ignition is whats messed up
Is the stator running wye or delta?
Delta
Do you have some experience with these big size LIDL drill bits, are they durable?
So what is the purpose of this video
2:34 a new vw model is ready 😂😂😂😂😂😂
What program you use to compile the G-code? HSM Works / Fusion 360?
you could provide me with a manual to do that?
yes, mikuskamartin (at) gmail com
@@Miki2T thanks my email it's superdilio120@gmail.com
czcams.com/video/3lkmFe3nxW4/video.html :)
Were you able to repair this?, if so how did you do this?, I have a similar sauter unit with the same issue, looks like the hirth coupling is worn. Sauter can still supply the parts but the cost is more than my entire lathe is worth. I was thinking about trying to shim the coupling closer together
Hello John, my sauter now works fine. the biggets problem was that I did not know how it works. the backlash catched on the video is normal. For real lock of turret you need press the magnet and turn motor to reverse direction as was last unlock. My problem was in the bed setting of encoder and centering of side plate.(two pins had damaged holes maybe after crash). If you need help (I have some servis documentation) you can send me an email to mikuskamartin {at} gmail .
These machines are pretty cool!, How far can the mill go in the Y-axis? Are you able to reach the front of the rotary table?
No need reaching the front of table if it ist rotary :D miki2t.rajce.idnes.cz/Schaublin33cnc/#9.jpg
Zajímavé události u vás jsou Kdo zná Miro Cibul"a?
Sucks to suck..
a to kde si tam štartoval?
www.pgcentrum.sk/letove-tereny/?teren=75
Noo veru, nevyzera to uplne zle a ma to dobru strategicku polohu.. Taka Suca na opacny vietor.
Tak ako píšeš bratranec, nad Devičanmi vedú občas trasy zo súče, snáď to bude niekedy aj opačne.
Nice and quiet shaper , unusual slide arrangements, do have more videos of it ? Thanks for the upload
img15.rajce.idnes.cz/d1501/3/3749/3749768_aafa57b6f6f1a44218268393a8be2a42/images/strigon.jpg
Thanks - looks a good machine.
co to je za kotol
VPTi-TDI (Variable Pumpe Timing-intelligent)
chodí to dobře, ale nestartuje. tédéíčka jsou držáky jak sviň :-)
velmi pekne videjko.. RIP kamosovi
next time why not buy 200 amps alternatorsee if see more power
@anthacdc Instead voltage regulator, I used constant current driver ( for exciting winding ). And behind rectifier one limitation resistor ( which is limiting voltage without load )
would you like to explain more,..please,..
wat did you modify on the alternator? Cheers
@sprogdiklis images: miki2t.rajce.idnes.cz/ALTsvar/
@sprogdiklis Voltage without load is 67V, and during welding is 25V.