Six8Ten Garage
Six8Ten Garage
  • 14
  • 450 377
Ducati Monster 695 Won't Start Ducati Monster Bad Fuel Pump Wiring
A quick run down on how to fix your Ducati Monster with no start. My bike was experiencing no start at, and I could not hear the fuel pump prime at all. A very good sign it's the wiring, or a bad motor.
The issue with this bike and two previous bikes I had was and remains the same cause. There is bad soldering jobs on these fuel pump assemblies at the connecting terminals. However sometimes it can be the motor, but this was not the case here.
::ADVISORY::
You are completely liable for your own repairs. I am in no way liable for any injuries, damages, or issues that arise from following this tutorial. Please use commons sense and other sources when making crucial repairs like this one here. Again use common sense, and please be careful when installing any parts that can cause issues and malfunction during vehicle operation.
zhlédnutí: 13 541

Video

How to replace the Tensioner Pulley and Drive Belt on a Chevy Tahoe
zhlédnutí 1,9KPřed 5 lety
A quick run down on how to replace the Belt Tensioner Pulley unit, and Drive Belt. Vehicle: 2001 Chevy Tahoe 5.3L Tools: (1) Ractchet, (1) 15mm Socket, (1) 10mm Socket Replacement Part: Drive Belt 6K930 ( goes with the 130 amp alternator) Replacement Part: DAYCO 89253 Tensioner and pulley Time to Repair: 30 minutes Before you purchase your belt, please make sure you know if your Alternator/Gene...
BMW E39 530i Camshaft Position Sensor Repalcement
zhlédnutí 8KPřed 6 lety
A quick run down on fixing that camshaft position sensor that keeps stalling, and cutting your engine off at the light.
BMW E60 525i Crankshaft Position Sensor Replacement - Transmission Error P0700 , P0335, P01727
zhlédnutí 76KPřed 6 lety
A quick run down on how to replace your BMW E60 5 Series Crank Position Sensor, and get rid of that Transmission Error! 1) Remove your splash shield under the car 2) Remove the Aluminum Support Plate 3) Looking up on the drivers side locate the starter 4) Directly under the Starter is your Crank Position Sensor 5) THIS IS A VERY VERY TIGHT SPOT, AND SENSOR IS HARD TO SEE! 6) Feel around the sen...
BMW E60 525i Transmission Error Fault ((PART 1)) Code P0700, P0335, P1727
zhlédnutí 74KPřed 6 lety
In this first video I corrected and addressed the error code P0700 that is related to the Transmission Control Module. Error Code P0700 was fixed by replacing the battery, and cleaning the alternator coils and mag to provide sufficient system charging. The alternator was not fully charging the battery/system causing all kinds of dips in voltage. The other codes relating to the cam and crank sen...
Lexus GS430 Instrument Cluster Removal and Indicator Bulb Change
zhlédnutí 16KPřed 6 lety
How to remove the instrument cluster on a 2001 Lexus GS430. 1) Simply pull back on the plastic housing, and it will come off. There are 4 tabs that hold this in place 2) Remove the 4 screws that hold the cluster in place 3) Gently pull the cluster out partially, and disconnect the two harness on the right side of the cluster. 4) Locate the bulb that is burnt out, and remove it from the cluster ...
Replacing the Lexus GS430 02 Oxygen Sensor - Bank 1 Sensor 2 - P0141
zhlédnutí 26KPřed 6 lety
A quick run down on how to change your Lexus GS430 Oxygen Sensor Bank 1 Sensor 2.
Mercedes W163 ML350 Oxygen Sensor Replacement Code PO151.
zhlédnutí 19KPřed 6 lety
A quick 3 minute video on how to get your Mercedes sniffer changed out, and that smog test passed. This is for the pre-cat o2 sensor, but procedure is similar for the post cat sensor as well. Check engine code PO151. If your scanner can read volts just use this feature to verify voltage comparison between Bank 1 Sensor 1 1) Jack up the car & remove the front wheel and liner 2) Soak the O2 Senso...
Mercedes Benz W163 ML320 ML350 ML430 ML500 Front Fender Removal
zhlédnutí 14KPřed 6 lety
Quick run down on how to get your old dented, beat up, faded ML320 ,ML350 ,ML430 ,or even ML500 Front Fender off. The good part is you don't even have to remove the wheel, or fender lining. It will take you less than 15 minutes to do this job!
Mercedes Benz W163 ML350 ML320 EGR Valve Replacement, Repair, Cleaning PO400 CEL CODE
zhlédnutí 58KPřed 6 lety
Here is a quick easy to the point video on how to remove your EGR valve and tube. If your getting CEL and CODE PO400 chances are the tube just needs cleaning, and or possible replacement of the vacuum lines. 1) Remove the Engine Cover 2) Remove your MAF Sensor 3) Remove your Intake Tube ( two clips, and one 10mm bolt) 4) Remove the Sensor Harness on Rear Passenger Side Fuel Injector 5) Remove t...
How To Remove BMW 5 Series Radio | BMW E39 Radio Removal
zhlédnutí 8KPřed 7 lety
How to remove your BMW E39 5 Series Business and or standard Radio Interface Deck
Mini Cooper S R56 Front Seal Repair Replacement - Six8Ten.com
zhlédnutí 51KPřed 7 lety
A quick run down on how to replace, repair, and or get to your R56 Mini Cooper S Front main seal. I will post a written step by step set of instruction on the site regarding how to use the special tool, and drive in a new seal. This repair was for a dealer friend of mine. This mini had been leaking since leaving the auction, and it was time to fix it. *Excuse my coughing and sniffling as seeing...
BMW E46 Secondary Air System Check Valve Replacement
zhlédnutí 6KPřed 7 lety
Quick run down on how to replace your E46 BMW Secondary Air Systems Air Pump Check Valve Replacement Step: 1. Disconnect the Air pump hose. One end is connected to your air pump, and the other is connected to the air check valve 2. Remove the air pump from its bracket, and disconnect the connection harness. This is located at the bottom of the air pump. Set the pump aside for now. 3. Remove the...
Audi B5 A4 1.8T Quattro Cam Shaft Position Sensor Installation - Six8TenGarage.com
zhlédnutí 79KPřed 7 lety
Just a quick video break down on how to change your Camshaft Position Sensor. General Symptom: - Generic Code P0010 - Car will not start - Rough Idle - Mis-Fires - Skipping - Basically your car may be running like a old tuna boat engine Car: 2000 Audi A4 1.8T Quattro Removal and Install Process: 1) Disconnect your battery 2) Remove the front Air dam ( trust me, this will help with the Timing co...