Video

@@junaidahmohamedsaman7612 Welcome. Thank you for sharing your success story👍😊 Wow 8 years. Last time product does last so much longer. Hope it can last many more years😊

@@MarJorieMamaril-s1i Hi, when you press stop button does the water stop? If it stops then might be your water pressure sensor that is faulty. Not very sure but that's what I will suspect if it happens to me.

Nice 👍, thank you so much for leaving a comment. ❤️

Hihi, the door roller have 2 type one if a washer in between and one without( what I used in the video) Maybe you can click this link and you see the door roller there is a slight difference- s.lazada.sg/s.1f4rh Hope this is the gap you are talking about

@@diyyangSG think i find out the issue, is the riveted stopper at top. Its like below the rail now. No idea how to solve this

I have not met this issue before, not able give advice to help 🙏sorry

You can take a look at this CZcamsr video for descaling valve issue. I think he does a very detailed video. That might be able to help you. czcams.com/video/esZ95CzWrfA/video.htmlsi=Io064tGQPjpfVqmE

Hi, if the solenoid does not make any sound when take in water then changing the valve most probably will work. But there got a slight possibility that is the main board have issue not sending signal

Glad it helped! 😊👍. Thank you for leaving a comment

Agree with you. Hope someone will create something better in future. Safer for everyone to change out themselves

@@motshehiramakatsa1724 Hi, Have no experience that on this machine yet but when you press stop does the drain pump stop? If not, likely the drain pump is spoilt.

Hi, mine just hang there, mine didn't move on to spin cycle so I just tried to change valve after I check my water supply hose is not blocked

@@diyyangSGhi, i just changed the valve, still doesn’t work😭

@@hidayahrahman1365 ohno sorry to hear that, this sounds like it might be board issue

In the event your rod drop out. You just have to hook the rob back in place. It will be back in balance again. Mine didn't drop out so I didn't have video clip on hooking back 🙏

Nice, thank you bro for leaving a comment to let me know ur success👍👍😊

@@diyyangSG you’re welcome bro. Cracked solenoid casing. Replaced the whole module and the washing machine water issue is now solved. Cheers bro.

Hi sorry, I have not tried it before. Not able to help on that 🙏

I haven't try before but I think it is possible if the error code for no water only appears after awhile

@@yennycoquin653 hi yes, need to buy a new solenoid valve to change. Do take note is not 100% success rate. Some did share can be circuit board issues too.

Nice! Thank you for letting me know Ur success 👍😊

Welcome 😊.Nice job👍👍 thanks for leaving a comment to motivate people to try

Welcome😊👍. Nice job. Glad to share and help. Thanks for leaving a comment 🥰

Welcome👍 Great job. Thanks for leaving a comment to motivate people to try out too😊

Thank you so much for the kind words ❤️🥰. Hope the video will help someone in this world

Nice. Great job 👍

Hi, first maybe you can check whether your water supply have any issues. Second, i will use a multimeter to check whether there are 240V sending to the solenoid valve. Because i hear before that there are chances the board could be the issue instead of the valve

That's very nice of you🥰. Thank you for leaving a comment to let me know ur success and appreciate it alot👍

Thank you for leaving a comment. All the best, you can do it👍😊 if it works you can save alot of money 💰

Welcome 😊. Nice job👍, Thank you dropping a comment too

Sorry 😔 didn't happen to me. Not very sure. 🙏 Hope someone experience it can share any solution

Welcome😊. Glad my video help you

Thank you so much for the kind words🙏. This comment gives me the motivation to continue sharing 🥰

Hi sorry to hear that. it is not a good news, there is a possibility your main board is spoilt or the wire is damaged somewhere. If you have multimeter you can test if the wire connecting to the valve has voltage during each steps and test the resistance of the new water valve. Otherwise, it is still better to replace the new washer instead. As the cost of the board is quite high.

Hi, I not sure which screw you are referring. I assume is the pipe you are talking about. If I am not wrong, it should be anticlockwise to unscrew.

Hihi, if you are scared and it is abit wet actually can leave it there. After awhile dirt will clogged it up. That's what I will do. But this is not a professional solution just my own personal DIY solution 😅 If it is very serious, replacing the whole thing is better. 🙏

@@diyyangSG hi bro, the whole bottle trap is brand new but I think the rubber ring got moved out of position while I was installing it into the main pipe. I tested it by turning the water on max for 1 min and had like 1 drop of water only. not sure if I should fix it or if it's ok🤣

I think is ok to leave it. If it is just one drop of water

Hi, is it draining give clicking sound (from the drain motor)?

Hello bro, as long as your rubber is on the pipe and you screw the cap for the pipe tight. I think the distance inside does not matter. The rubber prevent the leakage when the cap is screwed tight(hand tight is sufficient)

bro, so I had to reinstall because the top part was leaking, after reinstalling now the part I mentioned in my previous comment has some wetness when I rub with my finger but no dripping. really hesitant to redo again😢. is it normal or will it be alright??​@@diyyangSG

Hope WD40 works👍

Nope, I sprayed few times in 2 days. 😮

You might need to try using a hammer and hit the rod out.

Hi, Nope, the one in this video haven't spoiled till date. So depends on your luck and usage of the washing machine I guess

You can take a look at this video from other CZcamsr (czcams.com/video/0K6NaDiwDhU/video.htmlsi=Tuahfi0Bzj17Z1ud) but I believe you have to calculate the total wattage needed for Ur led driver too

Welcome. Glad that my video help you ❤️