Video

I need this for my shapeoko 4xxl

10:00 so before you turn off your laser always home it and leave it homed

Hello. I just purchased the 24 watt laser and just want to confirm that the setup in this video is the same for the 24 watt and the Onefinity elite series with Masso controller? Thanks!!!

Great video is it possible to do a material test using Lightburn and onefinity elite ? thanks in advance

Amazing!! We nearly had a laser machine out the window, becuase of the frustration this caused, especially wiht the homing! THis saved a lot of frustration, and of course, the need to buy a new machine. Great content! 💪💪

I would like to see it cut through 1/4" birch plywood with 5-layers. Not the cheap 1/4" as shown.

When using Start from Current Position can you physically push the laser to where you want it to start or must you home it and then use the move keys?

Thank you my friend. Your video saved my life.

Thank you!

This video explained a lot about what my machine sometimes does. very interesting. I only have one critique, the cursor is white and it makes it hard to follow, if you can change the color to green or red it would help a great deal. I had to stop and back up a number of times to catch where the cursor was going.

Why don’t you have any installation videos?

I have $32=1. And $30=1.000 (My S Value). 4% power button. As soon as I turn on my laser....it's at 100% burning my wood. Any other fixes for this that you know of??😩

👌👍👍👍 great tutorial . Thank You. GBU

What are the light burn? settings for upgrading to? 20W ORTUR .offset for the larger laser head.

are there any current promo codes for this laser? Also was wondering if u guys would no how much duty would be on this to get into canada

As a complete newbie with my Algolaser Alpha, when I try to set the laser to the center of a circle, (1% laser power on), when I hit frame the laser head moves around where the circle should do the framing seems to be correct, but when I hit start, I also get the first message of out of bounds, hit continue anyway, then a get a hard error with a g-code message stating an issue. Can I be causing my issues by physically moving the laser head by hand, or do ALL moves to a position need to be done with the on screen move command? A lower left star position seems OK but when I try to set the origin in the center, I get the two error messages and nothing moves. Any suggestions will be welcome.. Thanks

What are the proper settings for 2.4 laser? I can’t find info anywhere on this

any ideas on adding a monogram in the center of an elliptical cutting board , 13 inches by 19 inches ?? other wards , easiest way to do this .

What is the purpose of the spring?

This was great and has help me. I do have an issue with my 36w Wizmaker and homing i just received my new machine and when i hit home it run to the front left corner but the limit switches does not seem to work properly. It go to home hits it and sit there and vibrates. Same thing happens at the origin limit switch. I have been in contact with both lightburn and Wizmaker support but have not got the help i need. Also i get an error message #9 can you help?

Ha!!! this video is great.. I almost jumped out the window many times.... I should of washed this video when i first got my machine..

I made these changes and helped but i still cant get it to cut thru 3mm acrylic! 90% speed 150mm min and still scratches surface

Thank you your information solved my problem .

my life improved dramatically at 10 minutes ;-) that's been driving me mental...thank you

Extremely new here so I would ask that you SLOW down. The rapid fire explanations, coupled with the rapid cursor movements all over the board, makes for frequent rewinds to figure out how you did a certain thing. Great info, but for “101”, a trickle versus a torrent would help.

Wow this helped me a lot thank you 🙏🏻

thank you

Hi, I was hoping I could talk you into increasing the size of your pointer just a bit and/or changing the color. I am visually impaired and I only have my laptop to watch your videos. Thanks! Marie Wood, AcryliWood Designs

thank you! Wish I had found your video first lol

I just received mine and have not been able to get the performance as it is advertised. My 1/8” plywood will not pass through going over 18”/min. At 20”/min it passes through on cuts going with the grain but fails to go through cutting across the grain. So far, I don’t see a big benefit from our 24w quad pro. Maybe we are doing something wrong but I’ve been through the settings many times and can’t seem to figure it out… Currently using air assist at 20psi.

I'm trying to set up my xtool D1 Pro and can't get it to home. When do you home your machine?

Thank you, thank you, thank you. I Did my first ever test cut an hour ago with LB. Wish I had a look at your video before that ... but now I understand the different options. Thanks again.

Could you tell us what the kerf size is? I like my 24w but if the kerf is wider it may not be a useful tool for me.

What are the dimensions of the head?

How long can you run it without having to let it rest.

not a terrible idea, great to display till they rot, maybe it can be dehydrated and cast in resin, the scent of the spices will probably emanate gently for years.

Great video!

Is that just a piece of 1/8 aluminum that the standoffs are sitting on?

Is there a clear upgrade path from the 24w pro? Like using the same controller just buying new head?

I assume this is all with air assist, correct? $$$?

Happy thanksgiving J Tech!

You win for originality folks. And I guarantee your shop smells better than any other!

Took your advice but my 1.5kw laser didnt do too well....

it change the flavor?

I bought the pro laser and it doesn't have the back barcode on it at all and I cannot cut through anything at all?

Good info! I’m subbing just because you pronounced Porsche correctly!

My machine is engraving mirrored images, I havn’t found a solution yet.

Has anyone figured this issue out on the setting? I am not able to cut in one pass neither on a 4.5 mm birch plywood

Hi My name is Donnie I have just bought a Longer B1 2 weeks ago everything was running fine. Today all of a sudden my machine wouldn't go home it went to the far right. my jog buttons are backwards if I push the right jog it goes left up it goes down. It just seems like every thing is backwards. I'm using lightburn software any help would be appreciated Thank you Donnie.