Video

❤❤ Well done 😅😅

Nice video - I was under the impression the intake gaskets were typically replaced when doing this step. Even if they aren't visibly bad, you're already there so might as well. Thoughts? I have not yet done this - so just speaking from what I have read.

Thanks so much.

@EngineeredMojo Please share your email address, I’d like to contact you

Good job bro from St. Louis.

It's more other relays on the underside of dash

Timeline for drying is wayyyy off. Regrouted my shower tdy, followed step by step, and yeah a few things did not work. For other viewers your going to have to wait 25-30 min for it to dry if you do it in 10-15 like he says all your progress will be gone. It’s been a very stressful day trying to follow these instructions bc clearly it doesn’t work perfectly 😂

I have also used the C-Clamp while the caliper is still mounted squeezing the piston while still installed, before removing the pads and caliper. It ensures the caliper will remove easier.

I popped the retaining clips out without taking a picture and am fighting them because the inner brakepad dont wanna snap/slide/wedge in.

You don't need to primer, and if you do use primer you need to use high heat or it won't last. Just wasted time and money. Just a friendly heads up.

Intake manifold gasket not mentioned why not?

This was two years ago so you likely won’t reply to this comment in time but is it necessary to do the little half moon things?

My father's 2016 Grand Caravan just threw a misfire code on cylinder 2, and he has a 17 hour trip to do in a week... Such great timing. 😅 Although I'm no professional and I don't know if the spark plug could be the reason for the misfire, I would've loved to try this with him but he doesn't want to haha. Now the engine vibrates quite rough at 1-2k RPM.

This video is so boring

Awesome thanks!

Im a little confused. I only saw one gasket removed when you took off the lower part of the plenum @6:15. But you said there was 2?

Are there any more areas that need gear oil replacement on a 4x4 T100 besides the transfer case and rear diff? What about the front axle?

Thanks brother. I wasn’t 100% sure until I watched this. Everything went perfectly thanks again for the video

What a fantastic well explained video.

So, i have a question. When I took the CH-R to a dealership and mentioned the squeaky brake sound i was told they could find or hear the sound that I've mentioned about the squeaky brakes. As you mentioned in your video that the squeaky sound would be coming from the brakes being in contact with the rotor and it not being overly filled with dirt that's causing the sound? This has been going on for a week. Thanks in advance 💪🏼

Thanks for 2 bucket method.

Nice video! My client's own had a similar issue so I bleed the clutch and still to no avail. I've even replaced only the kit inside the upper clutch but the problem of a sponge clutch and no gear still persist. I've checked scrutingly for signs of leakage carefully while someone was depressing the clutch pedal and found out that the down clutch nipple doesn't hold clutch hydraulic fluid! It goes out gently, and also the clutch fluid was replaced with a new one. Nevertheless, it's still very darkened in color. Please, how do I fix the issues? Darkened fluid, soft clutch pedal, and a most especially the leak at the down clutch bleeder or nipple.

u da man!

Nice video! My client's own had a similar issue so I bleed the clutch and still to no avail. I've even replaced only the kit inside the upper clutch but the problem of a sponge clutch and no gear still persist. I've checked scrutingly for signs of leakage carefully while someone and found out that the down clutch nipple doesn't hold clutch hydraulic fluid! It goes out gently, and also the clutch fluid was replaced with a new one. Nevertheless, it's still very darkened in color. Please, how do I fix the issues? Darkened fluid, soft clutch pedal, and a most especially the leak at the down clutch bleeder or nipple.

Thanks for putting your time into this video. I'm doing my kitchen counters for the first time.

Am going to tackle this weekend thanks for the video.

Thank you for your video. It helps a lot. I am a 75 senior trying to use the premix Grout.

thank you man this really helped

This guy is spot on with his videos, and he speaks englisl! Great video, makes things so much easier.

Very helpful video pal. Thanks a mil bro. 👍🏻👍🏻

So i have a 1999 Acura RL and my main relay is closer to the steering column on right hand side and it looks nothing like this relay. If there was a pin out and test process for my relay, it would be awesome.

From all places under the car to place the connector the japs selected under the floor mat to put the O2 female connector!., Geniuses!

Hey, I am wondering if your car horn would still sound when you locked/unlocked the car? My car will still horn when I lock/unlock but not when I press the horn button on my steering wheel.

So helpful, thank you!

😮 what genius came up with this engine spark plug plan?

Thank you this is my first repair ever on car by myself and I did job perfect thank you I’m subscribing and looking forward to future fixes ❤ thank you

How cute, none of the Toyota Prius breakpads replacement videos shows pads adjustment (Allen wrench), as if it’s not applicable to this car. Is it true or false?

I own this vehicle, makes me miss my Jeep. To much work to get to the spark plugs.

Just a question. Would it be helpful to suck out all the old brake fluid reservoir before starting. If you do that you don’t have to push all that old fluid out the brake lines.

Toyotas do best with Toyota parts. It's also a good idea to put a dab of copper anti seize in the pad guide groove (top/bottom) and smear some disc quiet on the backside of pads.

Thanks so much, absolutely awesome video.

Must you purchase a new guard or can you replace the weather stripping

What is the torque of the screws? ? And what is the correct way to tighten it and in what sequence?

I am new to grouting. I have to regrout my bathroom. I decided on pre-mix. I watched utube videos. When I went to grout for the first time (last night). I ended up with my own method created out of responding to my own work. In the end I am doing the same things as shown in this video. Seems we arrived at the same process. One thing I will try, from this video, is applying more grout than I have been. I have been taking too long I think because I am really finessing it. I will try more course application.

upgrade your 1st Gen Tacoma door handles with Trubuilt Tacoma Metal Handles for durable replacements!

Ty for this!!!

Great video

**g rig. Dumb

not sure if you're still here amigo. But how did you de-pin them? Did you literally just push it out? Did you have to like lift up the bottom tab? I'm having extremely difficulty here. I managed to get one out somehow, destroyed another one ( so I need to fix it ) do I just need to use a needle or something to hit a retention clip and then push out? OR do I simply just push out the pin with a flathead??

rear and front same size wheels studs ? tnks 😊