Video

What fuel pump are you using ?

bad ass dude i love chevy motor!

Bro, you build these? What's that process like? Can someone just order one or do they have to supply all the parts?

Amazing content 👏

Roughly how much does an engine like this end of $running$?

Get to da choppa!

Can you explain that comp card please and talk as if you have a 6th grade education

Nice.

I wanna put it in a toyota Prius for ghits and shiggles

You should check out Clay Smith cams call down there and talk to grandpa. They’re the oldest cam grinder in the United States. Everything’s done in house you order a cam takes about a week to get to your house because it’s ground right then awesome people I just build 427 stroker. The rotating assembly came to me balanced from Ohio crankshaft I called because I remembered them when I was a little kid at the drag races and the boat drags in California. They’re based out of Los Angeles they like 93 years old, the business three generations the old man talk to me for an hour and a half half about the motor I wanted to bill I told him I wanted to make 500 hp to the fly wheel. He wanted to tire size gear ratio everything after I got my motor together I took it to my Dino shop. It made 500 hp on the button, I used a Brode stroker block and left the stock with 9 1/2 compression. It will run on the cheapest pump gas check out Clit Smith cams

Rev that thing up

That engine just Screams MERICA so loud.

Awesome

This is very wholesome... I'm assuming these kids in the video had something to do with the build if not everything to do with it... I'm in my 40's and I'm working towards building an engine on a stand like this, I'm very happy that they were able to do this at such a young age, it creates memories for life and it's something that allows them to feel like they belong in life even when stuff gets hard in life. Thank you for sharing this, it made my day for sure and I hope you are doing well! it's been 4 years since the upload.

I could listen to that all day 👍👍🇺🇲

Nice 👍🏻

Beautiful music to my ears..love it❤❤❤❤❤

woah that sounds really good

🎼😎 🎼

Judging this guys engine by the way the cam sounds? Thats called 0 experience. Build your own and post it up for us to see . That will make a ton of torque great driver 383

To much talking not enough idle

I love the color and sound

Sounds great. But you never get that same rumble like you do when it’s carbed , same thing when I build Harley motors , the ones I put an S&S on or mikuni always sound raunchy than the fuel injection motors

Muffler models? 3” inch?

Hope he has deep gears and a 2800ish or better converter

I want to put one in my 2011 silverado single cab, is this possible

What camshaft

whats the color of paint? looks nice

That's a bad ass motor!!💪👍

Sounds good, what is it going in?

Ford engine blue is sacreligious.

I told u not to stick your finger in the electrical socket

Sounds decent and i love that blue on the engine. Blue orange and red are the 3 best colors for a fresh engine build

Do yall remember everything yall put in the engine

I just put on the same pan on my LT1 383 stroker. And is scraps the crank or rod ends when I rotate it by hand.. bummer.... Rip it down again to see what hits. Have you run into this issue?

Not bad enough for me !!! Sounds weak

Great job 👏

Very cool

Do you build those to sell Gary? Typically whats it cost to rebuild one? By the way they sound great

Where u located

How would this work in a 99 Tahoe

Excellent work young man! 🏁👌

Would love to see a build sheet for that beast. Getting ready to build a 383 for my vette.

Foraz10

What starter did you use on this build? I see its a Jegs Brand, but what model

U and your dad sell motors in the market of buying a good motor 78 elcomeno

Beautiful Build! I would Love to have that in my 2003 S-10 .Does your friend have any links to after the install

OMG I absolutely LOVE Chevy motors!!

Question: What are you using AND doing to protect the lifters and cam lobes from excessive wear ! Thank you.

nice job