Video

This series was amazing. So stinking descriptive. I’m about to tear mine (99 115hp) apart this weekend. Thank you for posting!

AT 1:52. VERY IMPORTANT!!!! THANK YOU!!!!

How do you tighten yolk bolt mine came loose?

Something happened in our family when a squirrel killed a nest of baby robins that lived under our deck. My sister and mom cried for a morning and buried the squirrel. Needless to say, another family member got ticked off and then blasted the squirrel to the afterlife. The aftermath was a fine and warning for firearm discharge in town limits.

Does the manual call for the loctite 660 or did you just use it to help with the damaged roller?

Looks good I just recently did the same on a 5055E, but not sure how to bleed the brakes. Any suggestions?

No paddle?

Each step explained well

Found a racoon skull today at six flags haha gonna clean it up !

Thanks for posting. Got a deer’s skull that I wanna try it on 👍🏻

hi, I need your help, I have a mariner efi 4 stroke 40 hp but my trim is broken, what model can I order online, I've looked at many but I don't know what kind of one it should be, it's completely rusted

Great. This allowed me to repair my carburetor. The problem was the o-ring. Thanks

I'm going to do the same thing for Buddy, bro. I heard one of those little bastards yapping the night Buddy went missing, and the next day I knew. I'm not going to stop at one, either. I've always hated those cowardly little bastards. Yeah, I understand that's how nature works, but I'm part of how nature works too, and I'm relentless.

that sting ray has a massive sword imagine if you get stung by it , unimaginable pain and death if they hit you in the wrong place

great series of vids, I have learned much. thank you for doing these.

Instead of jebadiah they put a twist on it. Jebadeezer

Great video, the tip of using the wrench to break the ball joints was spot on! I used that tip with it on the tractor and left the ball joints on the wheel hubs worked out great. Thanks to your video replaced all seals in less than two hours. Tractor is a 5410. Will be looking for more great videos. Thanks again from Alabama.

I figured this shit out on my own one day while working out in the sun when i was like 20

So happy I found this and that you took the time to share it. I am restoring a flats boat that went through hurricane Dorian in Abaco with this exact motor. It’s been sitting since before the hurricane. Thanks to you, I know I can get it going again. I’ll keep you posted!

Ty, the gun right off the fitting when I loosened the nut.

Wish I knew what was wrong with my L118! Won't fire without starting fluid, somehow a bunch of crap is in the tank ( looks like yours) and it keeps clogging my fuel line and it's leaking oil from somewhere. I mean it's all over the engine, can't pinpoint the location. Cleaned the motor looking mew a few weeks ago and it's covered in shit already. Previous tenant left it here so it just became mine. But it's a nightmare

Should have just kept the cat indoors. I hope you apologized to your daughter. Please be a better parent.

They got my cat Buu last night. Loved that cat. Hopefully the coyote is dumb enough to come back so I can get my get back. Rest easy Buu, see you on the other side.

What size is the socket you used?

On a completely unrelated topic, we explore why women live longer than men😐

How long is your boat ?

Where did you get your fuel pump from? They are like $400

Thanks I get my door fixed one the first try 👌🤙👍☝️

awesome video ! is he dead? that would be really sad.

All I gotta say is I love your videos the simple life in the countryside and thank you for teaching me a lot and showing me the simple things

so i checked everything above :) the thing that fixed my LA145 was removing the fuleline from the carb intace presing the throttel and using compressed air in the intace. prob got rid of something blocking in there and now runs fine XD

Sounds good. What is fuel mixture screws set to? I’m rebuilding my carbs

My bar was all chewed up by the maniacs who built my trailer cranking down the bolts with a drill. I had to beat the hub over with a mini-sledge and now it's over a bit too far and it's making the spring sit wonky. But at least the tension is finally correct. Thanks for the vid!

Save yourself the gloves next time. Put the grease and the bearings in a zip lock bag and then squeeze them.

Can confirm those connections up top, the ones at the rear of the tank (maybe mine had a bunch of junk in them,) were a pain. Sure it didn’t hurt to have the bed off already. Kudos to all you super DIYers. I watched everything and this was still a struggle bus. Every connection and fastener decided it was 23 years old and very comfortable where it was!

I will use this trick in Puerto Vallarta to make sure I get to the beach in time. Very nice! It should work perfectly from the bar.

Did your kit maybe come with an extra O-ring maybe to fit a different model

Drop the tank, the first time it's a real chore. 2nd time it's super easy. You can do this working on your back with only the front end on ramps. Just keep the gas tank low to empty before dropping it down.

I’ve been looking for weeks for this video. I must’ve looked at 100 of them and none of them go into detail the way that you have with the fuel rail, the intake manifold and everything to do with the separator tank fantastic job thank you. Now I’m feeling much better about tackling this issue

Good video, I just changed one on Mer. 115 hp. One tip you might want to try when threading the wires from the new tilt/trim motor up through that split grommet is to thread one wire at a time through and put a bit of grease on the wires. It makes threading them through the grommet a lot easier. I also used some very stiff wire and shaped it onto a long thin hook and used to pull all the other cables and wires out of the way when threading the tilt/trim wires through. That way the tilt/trim wires came right up through with no hindrance from all that clutter in the way. It will safe you removing the oil tank.

wheres free bird

Thanks a lot for the video ! Boat newbie here that need a video like yours to understand how to do it. I don't have the history of the outboard so I will change the impeller. Your video was clear, simple and well made. Thanks again !

Same dang thing happen to me, thanks for sharing!! 😅

I’m sick motion sickness

You do know you can use milnot in can to stop leaks in tractor tire. And it will not eat the rim of tractor

“I'm not a cat person, but I took that personally” *_beep_* *Friendly AC-130 inbound*

Good bye marky mark

Those bolts on the sides of the engine cover don't have to be removed you can just loosen them the cover is slotted

Seeing little Django in videos always makes me happy.

Cool vid, nice to have a friend with a machine shop ❤