Video

Lighting was very poor & visual close ups would help much

Hey - Just replaced my belt. This video was a HUGE help. The close up on the 4:55. PERFECT!

Embraco, That's a Brazilian Compressor...😎

Everything is running on my fridge but it’s no longer cooling. Is there a way to check if there’s been a leak?

Great video

Inside the drum in my dryer on the back is a black cup thing. It's loose. I don't see screw holes so how do I tighten it?

shouldn't have hooked your @10:14 hose up to read neg pressure, you put air / moisture in the fridge from the hose. check when its warn and it would have had pos pressure, or purge your line with gas first

you didn't clean the line...said it, didn't do it lol. get some Emory cloth for the next remake

Thanks

Thanks! I didn't know about 'locked rotor amps', this is very helpful for me to complete my diagnosis on our wine cooler which is out of warranty. I appreciate you not rattling around about nothing between your main points of focus. Have a good day!

THANKS

Como desbloquearlo manera fácil ycrapida

Great video. Followed this step by step and got my washer working within an hour. Thank you so much for sharing this :)

What side of the belt goes against the drum flat or ridges? Thank you.

Hi there. This is what I have, does it indicate a bad relay, it is a combination relay type. Whirlpool WRT111SFDW03. 7 years old. 11.2 cu ft size. Freezer on top. Start relay P/N: WPW10448874, aka W10448874. Capacitor ("cap") P/N: WPW10662129 Test relay connections with capacitor on the relay. Results: when together I can get cap to charge and discharge thru the start relay, just like it does when it's off the relay. With cap off and on, neither of the lower holes have continuity with each other. The hole on lower left has 0.0 ohms resistance thru the bottom blade of the back of the plug. The lower right hole has no continuity with anything but can be used to charge the capacitor for testing. The upper hole has 0.1 ohm resistance to the top blade on the opposite side. Remove relay cover and visually check. I cannot get combination relay apart without breaking it, so I haven't committed to that, yet. Ohm test the fridge compressor pins again. Make sure the Common (top) and lower pins are within 3 ohms. And the two pins at bottom should read about the sum of the Common with the Start and Run pins. See CZcams video... Results: Top and Lower Right : 4.4 ohm. Top to Lower Left: 6.0 ohm. Two bottom pins: 10.4 ohm. None of the pins are shorted to ground. My problem is it suddenly stopped cooling without noises or warning, but I caught it from hearing loud buzzing noise from compressor and relay area, and compressor was very hot. No smoke or smells though, and wires did not seem to be hot. Do you think it's the combination relay? Thank you!

I just had to have a new compressor in my 1 year old Hisense basic bottom freezer fridge. Thankfully it was under warranty and they fixed it for free. My concern is, if these compressors are so, cheap?. Will this one last another year, break and NOT, be under warranty. It's a basic 18 cuft fridge and cost me 800 bucks with ice maker. But 14 months great working then dies? Not cool. Thanks for that video . I thought maybe it was a start capacitor or something. But when checking the compressor, I did feel pulsing. But freezer died in about a week after temp started rising. Thanks

Very informative

Thank you! I was able to change our pump myself in about 20 mins and the sound of that washing machine is music to my ears!

What's that device name? That digital pressure gauge...

How much vacuum did it pulled

This seems to be more of a recovery pump than a vacuum pump. It could be used as a vacuum pump with some type of check valve/ oil chamber on the outlet side. I definitely like the idea tho because without the chamber your able to use it to recover with you can pull a vacuum.

Awesome, thank you.

Excellent How to Video 👍

Refrigeration compressors are low volume, for faster vacuum use an AC compressor for an old windows AC. drain the oil into a container before soldering, then add it back In. I'd put a suction line filter neutralizer on the suction side to protect the compressor.

Hi! My fridge fan nor compressor is turning on..What should I do?

You'll need an adapter for systems with 134a in them and if any others use the new threads on the hose nuts. I have a wagner valve that is the same design and lost the instructions, I wish you had shown more of them in this video. I had forgotten after piercing the pipe you remove the top of the piercing pin. Using an adapter it doesn't matter. I would put a plastic port cap on when finished for extra seal insurance.

Omgoodness thank you for this tutorial! I was loading my dryer with a blanket and then remembered to clean out my lint trap and when I pulled the lint trap out, the lint fell back down the shoot! I tried to stick a wire hanger (that I fashioned into a hook )down to pull it up but no cigar 😢. So I googled and came across your vid. All I can say is thank you for breaking it down because I didnt know what to do besides calling whirlpool. But I got my handy-dandy Ikea tool kit, and pulled my dryer forward out of the laundry 7:35 closet and followed you step by step so I could get into the lint container. My dryer is new so the only thing that needed cleaning was to get the sheet of lint out of the metal shoot! Took me an hour because I was more afraid of loosing all the screws lol!! So i put them in a cup. And Joila! Everything is put back together and my blanket is now drying!! Thank you so much!

Man, you are awesome. It was the fuse , replacing it good as new. Two repair shops in my town never made mention of it. Thanks 😊

Thank you so much for making this video!!! You answered all my questions and allowing me to feel confident throughout the process

What is the measure of those valves?

So what is the problem if it is running weak and the condenser coil is not hot and the refrigerator is about 50 degrees? Then later the refrigerator assumes room temperature and the compressor still runs? No oil leaking around condenser or compressor. Answer: you may have a bad LG compressor that has failed. You know the type with the recall.

What if mine is just noisy? It seems to b running well but it’s loud. I have checked the rubber isolating pads it is on.

Great information, The aquarium rock example jamming it up was relatable😅 I laughed out loud

I hope your wife doesn’t mind burn holes in the carpet!!😮

Am interested in learning this stuff

Great instructional video, it resolved my issue. Thank you,

What are the other two slots for?

Great video. Thank you! The old Aeropostale hoodie cracked me up.

So the compressor with a LRA 6.5...you said if it reads at 6.5 or more to start looking for a new fridge

Thank you great job.

👍

I just change my refrigerator compressor but it's not freezing like it used to freeze before, could the compressor be the issue or the oxygen Gass is not enough

Thanks homie! FIXED IT! $150 part. SAVED ME $3000 for a new set! Had these bastards I think over 16 years!

what to look for when buying used fridge compressor? which brands last longest and pump out more air?

Ing it’s Cletus from the Simpsons

So if the compressor is warm, the condenser fan is working does that mean the compressor is working?

nice video man

Can you explain what causes these valves to go bad I've never had a washing machine with this issue. I really like my Cabrio I just wish it had longer lasting parts

Excellent

My stator cover would not come loose after removing the screw. I tried pulling as hard as I can.