Video

Hello. The grounding cable must be installed so that it passes under the box, without looping inside the box. Thank you.

Hello, Are you interested in testing our products? We would like to invite you to test the Scratch-Resistant Windshield for your 2016 Polaris RZR 900

Are you using a vest? The best helps hold it in place

Um um um um um um um um um um um um um

Thank you for locations and mounting idea. Your comments were kinda dumb though as you talked about an off fan condition to drive through a deep water deep mud condition? Huh? What did you do before? You waited till it fell below fan on temp right? 😄

What is the name of the bounding terminal you use bro?

The Dog cracks me up!!

what you could do is unplug the fan from the factory harness and then it’d be complete manual control

$100? 🤣😂🤣😂

I cant seem to find one of these kits for a 2021 turbo

Hope you took your dog for a ride just patiently waiting the entire time lol

I came here cause I literally just had the same issue taking mine out, ended up just taking the u joint out from underneath and separated the shaft that way. Probably the hard way but I was on a time crunch and that was the first thing that came to mind 😁

Good video

I'm running 34s on the same bike. Had the SATV driveshaft and cast carrier bearing installed also. A few rides later, I hear the exact same knocking. It vibrates my entire front end. I'm going to pull my console and look at it. Thanks for the informative video

What size wheels? Are this 14 inch?

That doberman is ready to go!

Really clean work . Have you Jade a problem with the wire getting nicked with the metal ?

2021 xp 1000 and I have found and have same holes in roll cage. Will be running it through like that for light bar . Great video

Wow, that’s great. I have a Chevy express and fit my sons rzr 170 inside (removing upper cage) but hate spending the 20 minutes each time to put the cage back on. I’m thinking of upgrading to a promaster or sprinter and it’s nice to see they are so tall. I may end up upgrading my sons rzr while I’m at it. 👍🏽

Please show us how can we make our own DIY grounding adapter for ethernet. Something similar to electra health grounding adapter.

I wish they were still $69 lol

Thank you, I was confused as well. I looked all through the manual trying to get answers!

Nice video! Just a couple quick questions as I just order this exact same setup for my Polaris RZR. How did you wire your switches? Did you just run them to the fuse block? So you cut all your wire harnesses? What about the ones that had a relay on them? I am just having trouble on how to wire everything up to the fuse block.

I had this exact sound in my rzr xp 1000. Well informed video. Loved the fact you took the skid plate out as well so you can see whats going on while filming 🎥

Nice bro

Does it make a clicking noise when you’re driving it? My 900s makes a clicking noise and it’s coming from the flex bearing so I ordered a flex bearing to see if that was the issue.

Thank so much!! Wish I would have seen this before I bought it

I agree that the Dog is beautiful.

Where is your Relays?

Hello was just wondering why there is no black wire (neutral) connected to your main lug on the fuse block. I see a wire connected to the positive lug on vent fuse block. Thanks

Thank you for posting the video, there are very few pictures and images of these units inside of a van. Lots of people say it will fit but it is always nice to see one.

No way in hell there gonna let you disable it , that’s a huge liability . Dumb fucks would be burning shit up blaming the company ...

Hey Mr. Rambling, All that you need to do is put a power cut off switch in the fans battery + side and you can go off and on all you want..

Have you had any further success with having the electrical tape holding the electrode to the machine? I was having similar issue with the electrodes coming loose when mine runs or lays down.

Thanks for the video but you’re rambling!

Ha ha! Just kidding! Totally agree with you! I hate my stupid kit too. Right on bro

Before you get butt hurt over my comment just think about your reasoning mr snake skin. “The wires aren only like 10 inches forcing you to put it near the other connector points” ????? So they “force” you to put it in a convenient place already where other connections are? Why should they put more money into copper wiring so you could put it wherever the hell u think is so much better since ur an expert? You don’t like the fact you can’t override the fan off when it needs to be on? Does a mud hole trump your engine frying? You don’t think that’s a bad idea since u could forget its off? U think Polaris engineers don’t anticipate the fan will be running in high water at times? How bout just let the damn thing cool down before hitting ur stupid mud hole? Your flawed thinking is what’s wrong with America today. Jesus man do u hear yourself talk? “Yea boy let me get that kit that lets me turn my pesky fan off when my shitty Polaris is hot as hell” “yee haw” “I’d much rather roast my 3500$ engine than let my fan chip chop a lil water” guess u took ur fan shroud off too which is exactly why it doesn’t matter if you part the Red Sea when it’s running

Snake skin?

badass

They won’t let you disable the fan, too many idiots would burn shit up and try to blame them .

Jonathan - use Zonas tape around the chest - 2 or 3 times around - and the sticky zonas tape will hold it all in place even with the older design with the leads I did this to ensure the leads and pads stuck in the proper place to the dog and you can get your reading - you are right - we should not have to do this to get the product to work effectively

Where did you buy the radiator? I really like the cap location.

Did you ever get this removed, I'm having the same problem.

Did it take out all the vibration while in 4wd?

thanks for sharing. I was looking for exactly this item...

Is that the Dan river? What brand of snorkel kit are you running? I noticed you had a side mounted snorkel kit in the video with the belt exhaust fan. Did you scrap that one for the current setup?

I had this same problem today that you guys did and tried everything you did. I had to drill out the pin. It would not tap out. So can't wait until tomorrow to give this a try. I know my neighbor has one of these large hammer drills. Thanks for the tip.

can you show a picture as to how the clutch exhaust connects to the snorkel please

Tires

I have been struggling on how to wire the same fuse block to my Ranger. I only want power to come on when i turn the key. Thank You