Video

Just made one and pre test it and it looks like it’s going to work pulling out 60ft of 1” pvc

gods speed! thank you!

This saved me today, thank you! Amazing idea! You should make these and sell them. One tool I found online was $800, and I think your design would actually work better.

Genius!!!

You’re have great engineering skills my friend you should patent them with different size plates for other id pipes🙏

Man thanks just dropped my bore pump pipe down our bore hole 🕳 I’ll let ya know how I go with your idea

Thank you very much.

This is what I need, u need to sell those, make $$

awesome ldea

i know this is an old video ?, but i just wanted to thank you very...VERY much for postig this '' how too do '' video !..thank you so much !. i have a busted off drop pipe down in my well right now, i watched this video, and liked the idea versus paying 700 bucks for a tool called '' fetch it '' ?, really...700 bucks ??..no thanks !. back to your tool, loved the concept, but this version of your tool is only good if you have a large well casing ?, in my issue, my casing is only 2 od ?, sooo..with your idea..and me making a smaller version to drop down inside a 2 inch od drop pipe ?, i tested the tool on a section of pipe i had laying around ( same drop pipe that is down in my well ), took me a few trial and errors to get the tool to work like you showed in this video ?..but low an behold...IT WORKS !!!. so now i will get to try it out on the real pipe down in my well..lol.

Sweet.

Thank you so very much for sharing this great tool.

Where is part 3?

You say you hook one end of the shunt hooked into the the negative lead. Where do you hook the other end? Are you setting the multimeter to dc volts and checking across the shunt then? End to end of the shunt. Or do you mean hook one end of the shunt to the negative then test from the other end of the shunt over to the positive?

Was in absolute tears as I watch me pipe go down the bore!! 😭 this is the first vid that popped up on the tube and it worked a treat 🥳 thank you kind sir for putting the time and effort in sharing this great idea! 🙌🏼

Thanks for the idea! I used it and it worked perfectly.

Place this about 6 or more inches off the ground to keep the water cleaner. You can float a small colorful ball in the pan of water so you can determine from a distance if it needs refilling.

Brilliant and simple! Many thanks.

great idea!! i might have to borrow that one

I was sent this video and put it to use and made it and it worked

Would love to see a new video going in depth maybe a construction video

i have two of these a 9mm and a 50 cal the ball that rolled out of the barrel was a 9mm that i accidently loaded in with the 50 cals. this barrel is a riffled black powder rifle barrel and 50 cal balls do not roll out of it.

Amazing idea

Thanks heaps for posting this.. gave it a try on a 2mm pipe an we got it out.!! Down a very dark concrete bore hole..

Very smart-creative idea! Thank you for sharing Sir!

Thanks a lot for relieving my headache. I have been thinking about such tool for a couple of weeks for my water well pvc casing

Nice video; thanks for sharing! Our patented portable technology not only allows you to build a pipe on any remote site worldwide, but you can set up the equipment on top of a well, build a continuous pipe (well casing) onsite and as the pipe is made lower it into the well. The strong and lightweight pipe will never corrode! You can make miles of pipe this way in diameters of 3-inch (75 mm) and larger. If required, the pipe can be perforated before insertion also. Please watch this video.@

That's awesome. My 16 year old nephew is in to fabrication etc. I put him on making his dad one to pull an old metal pipe out of the well at one of their ranches wells. I'll let you know how he did. I was a ship repair yard worker for years in Dutch Harbor where you can't always get what you need so you improvise. I'm impressed your idea and the fact your brain works like that. Thank you very much. I subscribed cause I think you could teach me and my young nephew a lot of improvissing. I've always been a improvising type of gal. So I love your channel! Thanks again. Stay safe

Great idea. That other tool on the net is ridiculously priced at $650 for about a $50 tool. You can tell he trys to sell by saying it's worth it by saving thousands of dollars by not hiring someone to pull the pipe out..

Your tool is great. However my son made one from one piece of scrap steel. Worked the exact way but way way less cost Zero. Made in 10 minutes. Why can I not add a picture to the comments

You did not explain the “loop” on the “corner that does all the work”. I suspect it is a Mini Cable Clamp. If this is correct, you could replace the wonky key ring with 1/8 inch aircraft cable, looped and secured with those squeeze locker thingys . This would replace the entire lifting rope. Here in Canada they sell 1/8 cable in bulk at Princess auto. Translate that into Harbour Freight in the U.S, And yes we spell colour with a U. Princes also sells Para Cord for the trigger string.

I think I get the magazine idea, it looks like a bolt action but sideways, like in any magazine the ammunition are pushed through the magazine in a "channel" by a spring and on this model the side of the barrel is bored the size of the ball bearing and the circuit is closed and rendered airtight with a sideways bolt, it's like a regular bolt action but perpendicular to the barrel! When the bolt is open the ball bearing goes into the bolt chamber then when you close the bolt it pushes the ball bearing in the barrel chamber and close the barrel to make it airtight and ready to shoot. That's easy as 1.2.3 when you think about it, but I would never have though of it alone. Great video!

Don't bother going to "Spudfiles.com" The images he talks about are not there anymore.

Please do it again with instructions

G u n

Hi .. such a genius idea. Do you think it would work with 300 ft 1.5 inch galvanized pipe that has broken in two ( 150 ft each ) and they rest on well bottom ( 480 deep ) ? Thank you so much.

I want to buy this for my PVC pipes stuck midway in the borewell. Please courier me this to Chennai, India. I shall pay u in Indian Rupees.

U should use a pressure washer trigger instead of a qev and just normal steel pipes for the gun

We just lost a pipe in a 300 ft deep well and we didnt wanna pay 3000 dollars to get it fixed. Do you think something like this will work??

Thank you very much! I made this tool, and tried it. Put the fishingtool in the well, and the first time was good and I fished the pipe out of the well!

YOU'RE A GENIOUS. YOU SHOU PATENT IT...

Hi there. Thank you so much for the video. Copied your contraption to the Tee and I was able to pull out my poly pipe that had detached from the pump and motor. I was so excited it worked. For a minute I thought it was a waste of time. It saved me quite a few dollars I would have been charged by the guys who fish them out.Thank you so much.

genius

Thankyou so much for this video. Our last length of pipe fell down our bore hole on our windmill and your video saved the day. We’ve been able to retrieve it and have water at the house again. Thanks from Jimbour Australia!

I need one of these. Very cool. Is there a build video?

Clever idea.

Very useful video. Thanks a lot.

Brilliant concept. Just saw this video and I will try it tomorrow in my well. Pray for me 🙏

My well point broke off and fell down the well. I tried your ideal and it worked great. Three thumbs up. Probably saved me a bunch of money.

thank you... nice idea ....simple tools but awesome .....so very very thanks .....regards from indonesia