Video

What happened to this bike did you fix

Bro this literally just happened to me all the way down to pulling to the right while catwalking 😮

Your amazing keep up the good work your probably smart as fuck now

Let me ride your banshee kid

I might do this bro I'm on a budget and just need the rears to work Incase the fronts don't work I'ma mainly use the front but just have the rears fixed I'm hoping this works

I cant find any info on them bikes but their cool

My guess is you need to replace the belt. I'm not sure, but it may have a grease fitting for the clutch so it will move in and out easy. There are 2 cables on that clutch levers. Make sure those are set right.. I would like to know what you figure out with it when you get a chance. The clutchs on this machine are sentrifical so the faster the engine goes the more the front clutch moves and the back clutch moves one goes in the other goes out.

I got same car 96,000 miles

What a shit video for 2 mins you showed nothing but a piston going in and out and then tried teaching us how to wheelie bro wtf are you on 🤦🏼‍♂️

Hey i know this is old but do you happen to know clutch cable routing?

How many links was the chain ?

Mojaves demand high-zinc oil for cam & rocker life.

The funny thing is the baja storm 125 i just purchased last night might be stolen smh

So I got a question for, I got a 03 raptor need some help any way you could some how contact me some how I’m having a no spark issue if you wouldn’t mind helping ???????

How many times r u gonna show it falling in and out

Dual overhead cams

Nice man mine was an 03

How to tighten a chain on this quad

Hi i got a Blaster and im running a 280 Main Jet wt. open lid filter and DG Silencer When im Running feels Bogging until it reach higher rpm wath could be i already Clean the Carb and put new Reeds On … i Need to Tune or go up or Down on main jet??

I'm old but I have one. HEY U GOTTA HAVE ZINC IN THAT OIL AND A LOT OF IT OR THOSE CAMS WEAR OUT QUICK & IN A HURRY.

I would of put oil injection block off on it

Do u still have it ? I have about one ☝️

nice quad I have a 2001 Yamaha Raptor 660R Yamaha 600 twin snowmobile engine she's wicked

Do not listen to this kid you're going to end up getting water inside your caliper and you're going to end up f****** the whole thing over do not grind it with a grindstone use a little wire brush on a air tool and go easy on it it should not slide in and pop out that easy it should take a little bit of thumb pressure to push it through just a little bit

And that's what's bad for Is motor especially during December... The oil is so cold it looks like molasses... Is very thick during cold weather... You do a cold star and You start just Reving it ......not good to rev while cold.... Let the motor expand a little from the heat and let the oil warm up a little... Then start giving it the rpms

Nah bub you gotta take the right side hub off Because there's a big ass snap ring on the right side you gotta pull off

I owned an ATV shop in Oregon out by the Bandon Dunes and between the racers and the basic ranchers ATV's i tuned quite a few...Your "clinic on what you call "Redneck Tuning" was Very well done and even a non mechanically inclined owner would get his bike running well in a short time....Great Job !!!

Where are you from lol my brother fucked with my tuner on my bike and now I would like to know how to fix it with hands on

I have one that is cleaner than that today lol

it looks good bud! I love working on the old Blasters, I just built a 06 SE Blaster with a DT200 engine in it, ported with the harness and powervalve hooked up, I mounted 1985 rm125 rads on the front and I want to get a capacitor instead of a battery, I have a dynoport pipe on it and a 30 pwk with vf4 and cfm airbox, I havent rode it yet but hopefully tomorrow I will

8 years later that quad is probably worth $1500 from Covid lol

How long does it take to swap out a cam start to finish

Yoo I got same bike I need help

Get a new camera man

you are supposed to have an rubber O-ring on the groove of the NEW pad so water and mud don't get in ur caliper, once the oring is installed the brake pad will no longer fall in and out like that. But props for cleaning it up

Hey man, how did you split the case?

Since you cut that wire does it charge your battery still

I want a banshee so bad

Those valves are out of adjustment. Common issue on those.

Thanks buddy I was too afraid of going in there with a little more power with the Sandpaper I just went over it real lightly on another note you got me laughing my butt off when you say the word brakes and you hear the whistle like the otter from Winnie the Pooh at 2 minutes and 17 seconds but yeah thanks on the tip

Paint looks fantastic

Still respond to comments?

That’s the exhaust filter homeboy

Where is the exhaust belt and what's the little blue container under the seat is it cooling or two cycle oil I just got one mine starts but won't get a lot of gas trying to figure out what it is

my motors been torn apart by many people and seeing one look this clean makes me happy

3 minutes takes longer than that to clean my ass

Son there's no need to cut wires when you can just unplug them

I need to find replacement bearings for the rear axle

Go more into detail of like putting the shift shaft and that tensioner in plz lol

Where can I buy some