Video

Every useful thanks

I shut everything off 😂

​@allelectricalau was I reading your multimeter at .710 when you checked for dead on the earth?

You should set your Meter first before switching the power point

kollam

Thanks!

Great video , hate it when isps cap the upload 🏃🏃🏃 , but great upgrade

Mate as a retired Sparky, Yeronga TAFE 1980 to 1982, that is very informative for a lay person especially checking polarity at the end. I am about to swap out some doubles to four gang ( they were not available when I was a boy but wood blocks were still being used) so just wanted to check that it is a neat swap and ended up watching the whole video. Thanks muck.

Great video ! Quick question, have bought Clipsal Classic Series Double GPO's, and have noticed that some of my current GPOs has 15A mechs in them. the new clipsals come with 10A mechs. will a replacement from 15A to 10A be OK ?

Can you do 8 different lights with 2x2 way switches so 4 turn on off each switch 4 switches total?

For connectors. What do you think about wago 221 connector. Waiting for the day they become standard rather than the old connectors. Easier to disconnect and reconnect.

Brilliant

My down lights are the plug in type so i just get a new one and swap them. My old house was hard wired like these. When they died i just left them until enough of them burnt out it warranted paying an electrician to come out and replace the dead ones but doing that meant that the next time they go.... They all go..

Thanks for your video. I'm gonna give it a go tomorrow. My bathroom has one light but two switches for different modes

can you use 2.5mm for a light if you don't have 1.5?

After uodating my wall switches i noticed My house has both configurations in it, weird. Have you ever seen this before ?

Good video man, where would a dimmer sit in this configuration?

Thanks heaps mate, great work

Hey mate wondering if you could tell me how I would go about adding a completely seperate power point, is it just a matter of piggy backing off the existing one in the room or have I got to run new wires down from the roof?

Great!!! ❤❤❤ thank you

Where i live it’s mainly non experienced installers who have completed some course, one told me they get $300 per install, need 3 per day to make it pay…

May I ask where is the new cable connected with the existing system?

Hey mate, is the double screw terminal on the earth circuit an as3000 requirment or personal preference? My sparky did not do this in my house, all done with single screw terminals.

Another video of installing an exhaust for the bathroom in an existing light baton would be good 😊

Great vids. Any chance of showing how to wire an isolation switch for a GPO?

If it was up to speed, none of us would be upgrading !!!

This should be a mandatory video for TPG Australia.!!!

Agreat handy video, just the one I'VE been looking for, having NBN in tomorrow to do the change over and as a retired electrician I had a 1000 questions and they have nearly all been answered here thank you

As a licensed electrician this video is scary… too many home DIY’ers watching these things.. I’m glad I don’t work in residential anymore.

More videos please mate they're very helpful for my apprenticeship

What a great teacher

perfect explanation.

Mate, this was a really great explainer! Thank you!

Those AFL connectors putting fusion splicers on the shelf, it's funny how these companies take advantage of the resident not knowing anything about acceptance loss. I figured you lost about minimum .4 dB possibly .6, the contamination was all over plus a good tech would have cleaned out the bulkhead before insertion, regardless. If he had burned on pigtails, could have been less loss, around .2dB, it depends on what kind of upload application you are needing at the residence, so for every 1dB loss is 20%. I did not see what the power meter was reading but a good tech would have had OTDR and calculated all the loss for you to the NBN. Some facilities would never allow those AFL connectors, it's residential so, the hell do they know, If you are paying for that drop, 100% I am sure you not getting the full benefit of that SM.

You forgot to use a ziptie on your socket.

I can't believe that your NBN provided uostreams are only 25mbit on a 250mbit plan. In NZ and the US they're symmetrical for most ISPs.

Awesome explanation, awesome video, well done mate.

Well explained :) Can a two way switch work if the wire to the light originates at the first switch (active in) or must the wire to the light originate at the 2nd switch in the series? If you can what is the wiring configuration in that situation. Thank you.

Hi, thank you for posting this and the drawing. I found this really helpful. Would you be able to add to this by showing how you would add a third switch? I believe a 4-way switch is needed?

Hey mate, when installing a new GPO is it safe to daisy chain from an exisiting GPO or do you install a new circut on the panel? Cheers.

Was your hole drill size larger than the actual Downlight? 90mm Downlight, 92mm drill bit?

Huh????

How much would an electrician charge to do this?

In NZ they appear to use 3 core yellow TPS for 3 way switching, but in Australia we just use twin active?. Is it a new standard like the blue TPS for A/C but it just hasn't caught on here?

Good stuff Bud.. Thanks a lot

I am a visual learner and this made it so much easier for me to understand how it works. Thank you 😊

Hi, Great info! I have similar shitty switches and my wife wants frameless windows (so no trims around the windows). Mounting brackets are the only way to keep the architrave switch in the same place?

Greetings from South Africa. I am grateful for your education.

Such a great video.

NTD mounted on the piss, PCD just slapped on the wall with cables exposed and slapped into the bottom, no corro, nothing neat. NBN is a disgrace, couldn't of made the job any easier for the bloke