- 105
- 940 438
MuLife
Canada
Registrace 27. 08. 2016
Welcome to MuLife channel.
Remember to follow your passion, be prepared to work hard and sacrifice, and above all, don't let anyone limit your dreams.
Enjoy !
Remember to follow your passion, be prepared to work hard and sacrifice, and above all, don't let anyone limit your dreams.
Enjoy !
R32 GT-R Finally gets a remote !
This works for any classic / base model cars that did not come with a factory central locking system , super simple to install with the kit providing everything needed to make it work.
Please support this channel by hitting the like , share and subscribe button !
Snapchat : mustafa-jh
Instagram: mustafajh
Tiktok - mustafa.jh
Email - Mustafajafarh@gmail.com
Please support this channel by hitting the like , share and subscribe button !
Snapchat : mustafa-jh
Instagram: mustafajh
Tiktok - mustafa.jh
Email - Mustafajafarh@gmail.com
zhlédnutí: 229
Video
Honda Accord 2015 VSA / ABS Malfunction
zhlédnutí 16KPřed 10 měsíci
Common problem on most Hondas , If you have all the lights on and VSA malfunction with codes 121-11 / 85-01 etc. Most likely have a failed ABS/VSA Module. Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok - mustafa.jh Email - Mustafajafarh@gmail.com
Ford Escape Intermittent no start , No crank !
zhlédnutí 1,3KPřed 10 měsíci
You can send your ignition housing for service with life time warranty. Ford Escape / Focus , Mazda Tribute and few other cars share this same ignition housing , and all of them have this common failure. Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok - mustafa.jh Email - Mustafajafarh@gmail.com
Kia Sorento Module 3 fuse keeps breaking
zhlédnutí 4KPřed rokem
Fuse Module 3 10 AMP kept breaking without any codes. After eliminating few circuits and inspecting the rear , the culprit burnt back up sensor and harness was found. Fixed harness and replaced sensor. Issue has been fixed and all the function specially cluster is back working. Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustaf...
ESL REPAIR / EIS REMOVAL PT 2
zhlédnutí 21KPřed rokem
This video shows how simple it is to diagnose your M.B electronic steering lock and replace it with a bypass or a new unit. These are very common for them to fail and will not allow the vehicle to turn on or start. Contact me if you need any services related to keys or bypass modules through any of the below. Please support this channel by hitting the like , share and subscribe button ! Snapcha...
RX8 Ford 8.8 diff conversion ! Channel updates
zhlédnutí 2,1KPřed rokem
The kit used to make this possible was purchased from Ronin speed works. As discussed the channel name will be changed moving forward ! Website for tools - www.vepro.ca Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok - mustafa.jh
Infinity G35X fuel gauge fix - P0462
zhlédnutí 15KPřed rokem
Infinity g35x 2007 came in with a fuel gauge non functional , every time the ignition is turned on the gauge reads Full. Tested and confirmed the floater arms are functional with a multimeter changing resistance when the arm is moved around. Turned out to be the AC climate control unit above the radio had 2 cracked resistors as seen in the video , some solder refresh and everything is back to n...
Dodge Ram 5.7 / P0688 / ASD / Main Sense CIRCUIT / MISFIRE
zhlédnutí 13KPřed rokem
Vehicle kept shutting off and would not start , code P0688 ASD / Main Sense Circuit. as seen fuse 52 kept popping and upon further inspection COIL 7 had a crack and was leaking onto the engine causing a short. Replaced coil with a new one and issue has been resolved. Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok ...
F150 2006 Limp mode diagnostics - P0022 / P0102 / P0135 / P0155 / P0433 / P0446 / P0645
zhlédnutí 4,4KPřed rokem
As seen the vehicle came in with lost power / limp / Safe mode with several codes P0022 / P0102 / P0135 / P0155 / P0433 / P0446 / P0645 which are powered by fuse 32 , fuse kept blowing up which meant there was a short on of the circuits. O2 sensor was melted on the exhaust causing the vehicle to go in limp mode and blowing fuse 32. Please support this channel by hitting the like , share and sub...
Ceramic coating my R32 GTR !
zhlédnutí 303Před 2 lety
Surprised to see the end results with the Avalon King Ceramic Coating. Highly recommend this product ! Click the link below for yours ! glnk.io/3owm/mulife Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok - mustafa.jh
M.B ESL diagnostics / Repair.
zhlédnutí 109KPřed 2 lety
This video shows how simple it is to diagnose your M.B electronic steering lock and replace it with a bypass or a new unit. These are very common for them to fail and will not allow the vehicle to turn on or start. Contact me if you need any services related to keys or bypass modules at the instagram below. Please support this channel by hitting the like , share and subscribe button ! Snapchat ...
RB26 PRP Ignition kit / R35 GTR coils.
zhlédnutí 730Před 2 lety
Upgrading the ignition kit on the R32 GTR using the PRP kit to R35 GTR coils. Everything needed to do the upgrade comes with the kit , Coils , Hardware , Prp bracket , Harness. Please support this channel by hitting the like , share and subscribe button ! Snapchat : mustafa-jh Instagram: mustafajh Tiktok - mustafa.jh
2JZ RX8 trunk panel - removing cluster lights
zhlédnutí 956Před 2 lety
2JZ RX8 trunk panel - removing cluster lights
Honda CBR 650 RA 2020 clutch replacement
zhlédnutí 6KPřed 2 lety
Honda CBR 650 RA 2020 clutch replacement
2JZ RX8 Finally gets an alternator upgrade !
zhlédnutí 1,5KPřed 2 lety
2JZ RX8 Finally gets an alternator upgrade !
R32 GTR | Differential / Transmission Fluid replacement + First drive !
zhlédnutí 1,1KPřed 3 lety
R32 GTR | Differential / Transmission Fluid replacement First drive !
RB26 FIRST CRANK | Nismo clutch and transmission install |
zhlédnutí 994Před 3 lety
RB26 FIRST CRANK | Nismo clutch and transmission install |
2JZ RX8 - 1000+ HP Fuel system upgrade ! ID Injectors + Double fuel pumps !
zhlédnutí 1,2KPřed 3 lety
2JZ RX8 - 1000 HP Fuel system upgrade ! ID Injectors Double fuel pumps !
R32 GTR Dashboard crack repair + Flocking !
zhlédnutí 1,3KPřed 3 lety
R32 GTR Dashboard crack repair Flocking !
2JZ RX8 EMU black - Connectors/wire crimping.
zhlédnutí 1,2KPřed 3 lety
2JZ RX8 EMU black - Connectors/wire crimping.
RB26 Final assembly. Oil Pan / Nitto drain.
zhlédnutí 866Před 3 lety
RB26 Final assembly. Oil Pan / Nitto drain.
What is the address to send for repair
Hello there, thanks for the video I have working on a 2012 message. 500 and I'm having the same kind of problem. I am wondering if this problem also occurs on the C LS 550 Thank you
Thanks bro did the fix. My favorite all time car repair video
How do you put the plates back on? Can you help me out please?
You suck! You didn’t fix it and judging by how you melted it open, you probably caused more damage than originally stated. You suck the big one ☝️
I was having the same issue replace both fuel pumps tried doing this but I removed the module but the chips or not broken. What other issue can it be?
I did the pump/sending unit replacements when my wife ran out of gas for likely the first time ever (yikes). Still reads full. We've been setting trip meter for 2 years when we fill up as a workaround. Now having possible clock-spring issues (flashing air-bag light), but the P0462 is the only persistent code showing. Regardless of current issue, I have not wanted to pull cluster, and seeing this I'm 99% sure it's the fuel gauge issue. Much appreciated! 😃
Thanks for that video helped me a lot on a car I was stuck on.
Is ir possible ESL failure to stall car while drive
0:30 When rx8 turn in to r32 or r34 😂😂
Thank you soo much! I had the same P0462 fuel sensor code on my 2008 G35 and it caused the check engine light to come on . I was gonna replace the fuel pump and fuel sensor but I decided to replace the ac amp control module first before messing with the fuel pumps. So i bought a new ac amp control module from Infiniti and replaced the old one and my check engine light went off and it cleared the P0462 code I had for several months and the fuel gauge is working properly now. I’ll probably wait until I get another fuel sensor code to replace the fuel pump and fuel sensor. I have about 200k miles on my G
Thanks for making this video. This was the only thing I looked at prior to R&Ring the rack in my X-Type and I had no issues.
Ty so much ❤ 😊
How much hp are they axles good for? How have they held up?
I have read but lost the info in my service manual that the later or earlier models are wired to the ac auto amp but the other year g35s are NOT and they are wired from the fuel senders to the cluster itself directly. This can quickly rule out if its a cluster or ac auto amp issues. Can you or anyone please verify which years g35 had the ac auto amp wired to the circuit and which DIDNT? i really dont wanna have to pull out the ac auto amp AND the cluster if one doesnt work. Its enough work as is.
Do I need a new ignition switch if the car doesn’t turn on once you replace the steering lock
No. Contact me by email for details, mustafajafarh@gmail.com
The brass ones I have seen are made for the 5 speeds only. They updated them later on to have 6 speed compatible collars, but I've never seen a video of one of these. Rmagic also makes a nylon one to essentially be an OEM replacement
Thanks for the great detailed content Very helpful Is it safe to keep esl installed if it fails in the unlock position and after you program and install emulator or it has to come out ??
Hello , your welcome. You have to make sure the ESL is completely unlocked and then unplug it. It can be left if so. Contact me by email for prices and details. Mustafajafarh@gmail.com
Could I simply cut off the locking protrusion tooth from the esl from the box so it will not engage the steering to lock it? It would be actually going to the lock position but unable to lock up the steering. Therefore not actually replace it with an emulator saving the cost of the replacement emulator and reprogrammed key fob? Or is this esl box tied to the electronics that requires some signal still preventing the start situation even with the lock tooth removed? Seems the emulator sanario is the easy way out if the steering is unlocked.
brother, i have question... Can i use oil pan RB26DET to RB25DET? Thanks
Did you have to remove the starter and the slave cylinder for this?
Thank you
Thanks brother. I did initally replaced my passenger side fuel pump on my 2012 fx35 due to inaccurate fuel gauge issue I had. Also, because the car is old so I thought the fuel pump and levelling sensor showed some signs of malfunctioning. However, the the replacement, fuel gauge is the same. It doesnt go down past 3/4. Finally, CEL came on with this code. followed your tip and found one resistor with cracked solder. Resoldered it and now it's all good again. More power to you! God bless❤❤❤
Great video! I am having the same issue with a 2012 SLK 350, can I used your Emulator to fix the problem. What is the best way to contact? Thank you 👍.
Hello , Please contact me at mustafajafarh@gmail.com
What material/adhesive did you use to seal back the housing?? I have the same issue it looks like and trying to gather info to work on it myself. Thanks!
when I smack the top of the cluster the fuel level reads properly but not all the time could that rule out that the cluster is the problem?
very good bro ❤
Where’s the rest of the video?
Hi i only had the code 85-01 i go stright to abs live data and shows in the solenoid valve (does not monitor) so what the mean is damaged?
was that a universal downpipe? if so what one
If i manage to unlock the steering wheel. Do i leave the key in and remove the esl connector and module etc or do i unlock and then leave key in and disconnect battery?
Merci !
Hi man, if we change with chinese motor, does the motor will last like the original germany, let say like 10 years?
No it will not , either bypass with an emulator or get a brand new ESL. do i once and do it right. contact me if you need an emulator at mustafajafarh@gmail.com
Since my ESL failed on April 5, 2023 until today 06/30/2023 I have seen and read all kinds of information on the internet about this problem and believe me when I tell you that this is the only video on the entire web which is professionally explained simple and coherent and straight to the point with no BS. My question is: How do I get an emulator from you, Sir?
Thank you , you can contact me by email mustafajafarh@gmail.com
@@MuLife Ok I will right now. Thanks for the reply.
Hi where is your shop? How can I contact you
Can a locksmith program a emulator?
Hey, I have the same exact car and my ac compressor doesn't wanna turn on unless i use some bypass in the diagnostic mode, and i had a shop tell me its either my ac amplifier, or the low pressure switch on the condensor, have you ever had this issue or have any insight? It's either one of those causing my problem and not sure what's more likely. Thank you!!
Hi, thank you for finding the solution that even the dealership have no idea how to fix this ugly Infiniti gas gauge problem. I would really appreciate it if you could help me with my issue after doing this repair. I have 09 G37x coupe, the only thing wasn’t working is the gas gauge, and the check engine was on for this issue only. Gas gauge was stuck all the way to full and never change. This morning I saw your video and I decided to give this a try. So I followed your steps and got the module out and went to an electronic repair shop and he soldered 4 resistors ( three of them marked (161) and one marked (181)) The guy soldered all 4 resistors and tested all of them and test passed. Went back to my car and installed the module and the gas gauge is fixed and no more check engine light. But Now I have multiple issues: the speed gauge is not working right and changes very slowly and doesn’t give you the right reading of your speed, also the rpm is doing the same thing, and I have the TPMS is on and the air bag warning is on. Thank you
Why are they making cars harder to repair,more money at repair time???????
How can I watch with that music grow up
Can you please send me your number so I can send you my parts for you to program
I have a e350 2013 with same problem I’m getting car back from Mercedes were do I send the emulator and key to program
Contact me by email mustafajafarh@gmail.com
Hey how can I send in my key so you can program it
Boy you are good
I have the same code on my 2003 maxima change the pump and sending unit still have the code.. does the 03 maxima have this module? And could this be the culprit for the code?
Mine only gives one code, bad neutral safety switch. But is running in limp mode. It's a 1988 Ford F150
What if none of the keys wakes cluster up and machine says key is good?
hey bro my esl lock just failed in the unlocked position. i was wondering if i can just take out the plug to the esl and plug into the emulator without needing to take out the esl
Great! Just the audio was kinda rough...
Great solution My car 2010 glk 350 had same issue .and fix it my self absolutely same method . I did it . Thank you so much.no questions this video is perfect!!!!!
Dude respect to you helping the g community keep these cars on the road man. New sub here for the simple fact that what you did here deserves a sub !!