- 12
- 22 871
Marius The Mechanic
Germany
Registrace 3. 11. 2019
Leogang Hangman 1 Reshape inklusive Drop Tow In
Leogang Hangman 1 Reshape inklusive Drop Tow In
zhlédnutí: 114
Video
Hacklberg Trail in Saalbach Hinterglemm 2023
zhlédnutí 1,6KPřed 10 měsíci
Hacklberg Trail in Saalbach Hinterglemm 2023
How to grease sealed ball bearings without removing seals
zhlédnutí 15KPřed 2 lety
Bearings often have very little grease packed into them. This is necessary for high speed applications and it's the way bearings should be greased. However there are some applications where bearings either make no full rotation or are spinning at very low speeds smaller than 100 rpm at very high pressures eg. linkage bearings etc. in that instance it is necessary to pack these bearing in order ...
X Line Saalbach Hinterglemm Trek Slash 8
zhlédnutí 183Před 2 lety
Die X-Line wird jedes Jahr mehr und mehr ausgewaschen. Wenn ihr die einmal fahren wollt, dann seid euch sicher, dass ihr da auch runter kommt, denn mittlerweile ist die wirklich nur noch für gute Fahrer zu empfehlen. Für fortgeschrittene Fahrer eignet sich eher der Hacklberg, oder die Blue-Line. Die Blue-Line ist wirklich super gelungen und macht extrem viel Spass. Da werden jeweils noch zwei V...
Leogang Hangman 1 10.07.2021 Trek Slash 8
zhlédnutí 2,2KPřed 2 lety
Leicht segmentierter Run vom Hangman 1, da ziemlich viel Verkehr war mit Anfängern. Das ganze ist aus zwei Runs zusammengeschnitten.
Antonius Trail Leogang 10.07.2021 Trek Slash 8
zhlédnutí 137Před 2 lety
Mit meinem neuen Trek Slash 8 den Antonius Trail unsicher machen. Reifen müssen noch gewechselt werden, weil diese "Leichtmantelreifen" sind einfach grausam. Deswegen auch mit 36 psi am Hinterrad und 32 psi am Vorderrad. Ging so halb gut, aber bevor ich mir die die neuen Felgen verbeule, lieber so.
P r o m o s m
What an idiot.
I give you the first dislike - bearing is overfilled with grease witch will create grease friction, heat, sealing issue ...
Yea mate well thought out , but really you could have picked the seal , cleaned out the old gunk with brake cleaner & packed with grease in the same time.
Why didn’t you just remove the seal and grease it, to begin with?
That’s a cool tool. But a more affordable way to do it is just to pop off the plastic seals with a pick and grease it like I did in my video here: czcams.com/video/aTkxEP7TcVs/video.html Good demonstration of the tool but sometimes a verbal explanation helps a lot. Thanks for the video.
Does not this prove that sealed bearings get the grease when greasing during the cutting season?
was there any doubt , a grease gun puts out 10 000 psi , where did these people think is was gona go ,
Die Kamera Position macht es Kaputt. Ohne was vom Bike zu sehen Schwebt man nur so über die Strecke.
Gibts was schöneres als über die Strecke zu schweben ;-)
@@mariusthemechanic3091 😉
why didnt you pop the the seal before greasing it??
Thanks M, I’m going to try this. 👍
To much grease
i know, reading is hard.
No such thing as too much grease
@@cheesefarmer3545yes there is. but not in this case
Is this apparatus available in market
lisle 65250, as stated in the description.
You know you popped that seal out faster than it took to set up that jig.
czcams.com/video/1vBesOFURek/video.html
Servus. Ist der Bongo Bongo mit der Hangman 1, oder dem Antonius Trail vergleichbar?
Ist mit dem Hangman 1 vergleichbar, nur etwas steiler.
I’m going to try this on a metal sealed bearing that isn’t removable. I hope it works
Just make sure that you don't force the grease. Slow and steady and it's going to work.