Video

Awesome vid. I have a home build cnc plasma and regularly cut 10mm - 3/8" steel and stainless on it. Didmt even know about the wiggle pierce in sheetcam. Thankyou!!

with this tech could boost my crop yield.

Couldn’t you use (Ceramic) Flame Holders for Turbulence without restricting the Inlet? Pulling more Air in seems desirable compared to increasing the Presurized Air Supply. I think you already had Designs with increased Turbulence for Burnout. "Little Dragon" or something like that? And your Air Preheat always looked good on the other Devices. Slightly below Cracking of the Fuel should move the Point of Vaporization for the Combustion back a tiny bit and might increase the Stability of the Flame at the same Time.

Where is the video on how you built the nozzle assembly?

I'll waiting for more oxygen!

You've got precious discovery out there, can it be used as crucible?

Интересная конструкция)))

Just an idea to mule about. You can probably get away without an compressor by building a self contain system, a Tesla turbine - Tesla (air) pump (as a compressor) setup, where the Tesla turbine will be driven by a steam, being created by the burner, and the turbine will be co-shafted with the Tesla pump (a Tesla turbine run reversely). The only disadvantage of such a system would be that it will have to be wrapped up slowly (clearly) till it get to an efficient working regime but for a long running processes will be an extremely efficient use of some of the exiting heat and (what is likely more important) for remote, sort of off-grid, applications will not require any electricity.

Sounds like you need a flywheel -pully combination.If you got the chunk of steel you can make it yourself.V belt pulleys are easy to make ,lust make sure that bottom of pulley is deeper than the root of the belt .Only sides of belt need to touch the walls of pulley.You can make the profile knife for it from hss blank easy by making a template on paper .most belt manufacturers have information about sizes and angles . As of flywheel its also easy ,outside of flywheel is heavier than the middle ,several ways to achieve this ,one is making it out of steel and leave outer width larger while reducing thickness of the middle pulley . If you work in aluminum what works great is cutting a dovetail groove in outer diameter of pulley/flywheel on both sides and then you pour molten lead in it -machine the pulley to size and balance it if needed.

NASA can relate!! 😅🔥

Keep the fire 🔥🔥🔥

heeeeelllllll yeaaaa brodeerrrrrr

How much compressor capacity do you use it?

why not turbo charge the compressor? if it's a gas motor powered compressor...

i wish someone could do torque tests with diamond like coatings with Pullys

Now your cooking baby!

Could the sparks injury your retinas?

Definitely neodymium magnets. I’ve got a Ryobi 80V, but the brushless motor is actually slightly smaller than this one. But I will say that the Brushless motor on the Ryobi cogs are very strong and tight. The motor is ridiculously fast for what it is. I only use it for small branches and tree. Say 6 inches or less. I prefer stihl gas 2 stroke. I will add that I have a cordless 80v Kobolt leaf blower that is a slightly older than when they made the switch to brushless so has a 80v brush DC motor that is like a 770-780. It is top of the line in quality, speed, and torque.

Is water going in that radiator?

The bee lovers are going to bee coming for ya

We usually have lovely skys and weather in the Caribbean, im not very far from there

Thats water being wasted. Steam is invisible.

Use a will bladder tank where you can pressurize the bladder overtime with the fuel and it would give you better pressure and cost-effective

In my opinion compresor should be closer to injection, it makes the geometry more stable Btw, Nice work

may be up size the jet if you ant all ready on the engine on compressor richen it up a bit the next size drill bit up the main jet via a hand mini drill bit i did that to my pressure washer and racing mud mower mud mower runs a bit fat fuel but no longer dies taking off due to up gearing and lack of traffic pump [squirter jet] all so on intake port add a ruff texture to the runner floor help atomize the fuel can do that with a burr going along the short turn of heads intake port .it will help possible fix the issue

Considering myself in the group of "men" I've fully enjoyed the video. 😅🔥

did u mean to say contrails or chemtrails 0:40

You know i always have an eye on you! Regards!

Why use oxygen if enough fresh air is available?

probably should have made it like a jet engine with can or flame holder on the inside

Ford is crap , so if your fender liner wasn't ripped apart you would need to remove the tire and fender liner for access to the valve.

How can the water go through the flash boiler?, are u using water pump sir?

What voltage was going to the electrodes here?

Do us all a favor and take down this video please. If you don't know what your doing then why post a video of it? It's clear that you have no idea how the torch works or why hole is there yet you decide to plug it up? Video like this cause injuries.

Lol. That's called, by a new deck!

Wiretek 1001 seems good but It's tough picking the right spot

Yes lawnmowers can be a real waste of time to fix. When I work on them I make sure it's a good repeat customer that doesn't mind spending money. Or it's an expensive mower that's worth sinking time into. And on stuff like that bill by the hr. There are many times I wouldn't want to hire myself

What thickness copper tube did you use? L or M?

Bro you should not be doing this. You have a leak by the way. Check your evap coil for a leak. And you dont go off psi you go off superheat subcool.

You have a leak if you have to recharge. Most likely it's the valve cores on those service ports. Put some 1/4 inch brass flare caps with copper gaskets on those ports to prevent leakage.

Wouldn't .68 caliber glass balls be extremely dangerous if they hit someone and shattered? Could the glass shards potentially cause eye injuries, blindness, or enter the lungs and cause internal damage like major cuts?

That's not a worn part, THIS is a worn part! 😅🐊

That's not a propane explosion. That is a high explosive. Nothing in an AC system can detonate like that except maybe C4. That outdoor unit must've had a bomb planted. Maybe if you charge the AC with propane and pure oxygen, maybe then it'll look like that. Without oxygen, nothing burns, nothing explodes.

tomorrow will be a better day

Wouldn't it be cheaper to replace the deck ?

Im having this issue as well but when i squeeze the trigger it seems that rhe freon isnt passing through, any clue why it would do that?

Most commonly a low charge is the cause of a frozen evap but there could be other issues. You can google a temperature pressure chart for the refrigerant you are using. I don’t do residential but I work on refrigeration. Always check airflow first. Nice clean coils. Then fan operation. Check for drain obstructions if all that is good and compressor is running then it’s on the refrigeration side. Put gauges on as a last resort. Also it’s good to see the high side as well. If you have a restriction, you could be overcharging by adding refrigerant. Gauges on the high press side would show you that. If you know u have a slow leaker then it’s probably fine topping it off like you did.

Anyone can tell me what to do if i checked the bulb but turns out to be a small LED light that sauderd

I think that they have a similar compressor priced at 2K in June 2024.

Hi Bob it's Dan from Israel im trying to reach you on phone or WhatsApp, no reply its shut down. How can i connect you please 🙏