Video

Thank you for your message. The affect lasts for 2 weeks. Or until you can't smell it anymore. Weather (wet, rain...) can make it shorter. Yu spot spray, so don't need to cover the entire surface.

Good morning, this product is not suitable for wet clutches. We recommend using the MoS2 shooter instead. Product code: LM3444

Good day, no unfortunately the cleaner needs to be applied according to the Technical Data sheet and bottle instructions, the product liability also falls away when you apply different, to the instructions. The cleaner is still more efficient, as the additive is mixed with fuel, where the cleaner is a direct application solution.

🙂

Hi Dom, yes this product is compatible with all commercially available injectors.

Good Morning, yes the fuel additive is compatible, but we would also recommend that you use the Fuel Protect (2530) to prevent corrosion caused by ethanol.

@@LiquiMolySouthAfrica Have you heard of a vehicle throwing a brief misfire code for a short time during the drive immediately after using Catalytic Clean 7110 as directed?

You're very welcome! I'm glad you found the information and demonstration helpful. Thank you for choosing Liqui Moly Bicycle Tyre Fix! Please let us know how it works for you. Greetings to you too, all the way from Chile! 🚴‍♂🌎

Hello Nicolas, the external Cat Cleaner has not been designed to add to your fuel tank. Have you done this and have you already driven? How many ltrs was/is in your tank when you added ?

If I added the entire jar, I added it a day ago.

@@LiquiMolySouthAfrica the gas tank was full

Good day thank you for your message. Our suggestion is, confirm your oil volume requirement, lets say it is 5ltr, then we would remove 300ml(Cera Tec 300ml) from the 5ltr can(new oil), add the 300ml Cera Tec to the new oil and then add to your car engine. This way you are sure you don't overfill. Then make a note of current km's and you then only need to add Cera Tec again after 50 000km. Even if you change oil in-between.

@@LiquiMolySouthAfrica can i put it earlier than 50.000?

Thank you for your question 6900pilot. The 300 ml of Liqui Moly MoS2 Anti-Friction Engine Treatment is intended to treat 5 litres of engine oil. This 300 ml should be part of the total 5-litre capacity. So, if your engine requires 5 litres of oil, you would add approximately 4.7 litres of engine oil and then the 300 ml of MoS2 to make up the total 5-litre volume.

@LiquiMolySouthAfrica will I do harm to my engine if I put 5.3litres instead of 5 litres? It's not much extra?

@@6900pilot Adding a small amount of extra oil, such as 300 ml over the recommended capacity, typically won't cause immediate harm. However, it's important to note that overfilling your engine oil can potentially lead to issues over time. Excess oil can create increased pressure, leading to leaks, foaming, or damage to seals and gaskets. It may also result in the crankshaft coming into contact with the oil, which can cause aeration and reduce lubrication efficiency. To maintain your engine’s health and ensure optimal performance, it’s best to keep the oil level within the manufacturer’s specified range. If possible, drain the excess oil to bring it back to the correct level if you already added the 300ml additive with the 5ltr oil.

Thank you for your question. Engine flush is like soap when you bath/shower, just with water you will get cleaner, but the soap will make sure all dirt removed. Engine flush has the same purpose, adding it to old oil every time before you drain, ensured as much dirt or thicker oil can be drained before you add the new oil.

Thank you for your message and we hope to see you as a VIP member soon. Please visit the VIP landing page, all the details are explained there:-)www.liqui-moly.co.za/vip-club/

Good day thank you for your message. The video is for Cera Tec, this a friction modifier that you add to your oil and it's guaranteed for 50 000km. Then you have our LM Engine flush, this is to clean the old oil out before you add the new oil, the Engine flush you will add, idle and then drain. So 2 different additives. The one you want to use?

Hi Gavin, Pour Cera Tec in together with the fresh oil when changing the oil. If used between oil change intervals, at least 5,000 kilometers should remain until the next oil change. 300 milliliters of Cera Tec is sufficient for up to five litres of motor oil.

Thank you for your message, but what is it that you want to know? Can you use the engine flush, or are you looking for the correct oil? Anyone can use the Liqui Moly Engine flush, we just require that you read the Technical Data Sheet and use correct. If you require the correct oil for your engine..Then please follow the Oil guidelines on the link: www.liqui-moly.co.za/oil-guide/#oww:/api/v2/oww/1002/ZAF/ENG/1/

Thank you for your question regarding Liqui Moly Cera Tec. For optimal results, you should maintain the correct oil level in your engine. Since your engine oil level is exactly full, it is recommended to remove some oil before adding Cera Tec. The amount of Cera Tec to add is 300 ml per 5 liters of engine oil. In your case, for a 4.8L oil capacity: 1. Remove approximately 300 ml of the engine oil. 2. Add the 300 ml of Cera Tec to your engine. This will ensure that your oil level remains correct and that Cera Tec can provide its full protective benefits. If you need further assistance or have additional questions, feel free to ask.

Thank you for your message. Note this is an oil additive, so it gets added to any engine oil, any type of car, the fact that it is diesel, is only important when you use our Fuel additives, then you have to make sure you use Diesel additives for your diesel engine. So yes, it can be use in your engine oil, for your Toyota Hilux.

​@@LiquiMolySouthAfrica should i use ceratec or this additive?

@@user-mr1qi7lr2w I suggest read both Data sheets and decide what you prefer. They are both Friction modifiers, Cera Tec guaranteed for 50 000km, Mos2 you need to add again on every service...both amazing, my favorite the Cera Tec...but investigate and decide what you prefer?

Thank you for your message. I do suggest adding the Liqui Moly engine flush with the old oil..to ensure all sludge and impurities are removed when the old oil is drained, that is what the engine flush was created for. Then to establish the correct oil for your Kia, we suggest follow our oil guide, to ensure you get all the correct details for your Kia, but also any vehicle in the future. Here the link www.liqui-moly.co.za/oil-guide/#oww:/api/v2/oww/1002/ZAF/ENG/1/

Thank you for your feedback! The video aims to describe the benefits and usage of Liqui Moly Fabric Impregnation. If you have any questions on the product, please let us know, we will be happy to assist.

@ignoredbyu, thank you for contacting us, Liqui Moly Ceratec is designed to be added to engine oil for enhanced protection and performance. However, it is not recommended for use in automatic transmissions. Please confirm what automatic transmission is your car, so we can suggest a recommended product for your car.

@@LiquiMolySouthAfricaCan I use it on Hyundai i40 1.7 crdi dct automatic?

@@harikrishnankr3134 yes you can use it for any vehicle engine oil, does not matter what type or brand. The Transmission is not connected to the engine, so as long as you pour the Cera Tec into the Engine oil of your Hyundai 1.7, all will be fine.

@@LiquiMolySouthAfrica i asked because you mentioned not recommended for automatic transmission in the first reply! Thanks for clearing that up

@@LiquiMolySouthAfrica how about Mini Cooper ? I have a 2016 Mini Cooper S 4 valve turbo automatic transmission

Yes it is safe to add the entire can

Here is a detailed comparison of both Motor Clean 1. Purpose: Designed to clean the interior of the engine before an oil change 2. Usage: Added to the old engine oil before an oil change. Run the engine at idle for 10 to 15 minutes 3. Features: - Removes deposits from oil holes, oil screens, piston ring area, and other engine components - Dissolves sludge and lacquer - Suitable for all petrol and diesel engines with and without a diesel particulate filter (DPF) - Improves engine performance by reducing contamination 4. Pros: - Effective in dissolving stubborn deposits - Enhances engine longevity and efficiency - Easy to use before the oil change 5. Cons: - Requires the engine to be run at idle for 10 to 15 minutes - Only used just before an oil change Engine Flush 1. Purpose: Cleans and flushes the oil systems of petrol and diesel engines 2. Usage: Added to the engine oil before an oil change. Let the engine idle for 10 minutes 3. Features: - Cleans the oil system of the engine - Dissolves sludge and lacquer - Suitable for all petrol and diesel engines - Ensures the new engine oil can deliver its full performance 4. Pros: - Quick and easy to use - Improves engine cleanliness - Helps new oil maintain its quality and performance 5. Cons: - Requires running the engine for a short period before an oil change - Similar to Motor Clean, it is used just before an oil change Summary - Both products are designed to clean the engine's internal components before an oil change, dissolving sludge, varnish, and other deposits - Motor Clean is particularly focused on thorough cleaning of the engine internals and might be slightly more effective for heavily contaminated engines - Engine Flush provides a quick and efficient way to clean the engine, making it convenient for routine maintenance In essence, both products serve the same fundamental purpose with slight differences in their formulation and specific application details. Your choice may depend on the specific needs of your engine and personal preference for the cleaning process. Also all countries might not have both.

Cera Tec (code 3721) is a high-tech ceramic wear protection product suitable for use in both petrol and diesel engines. It can be used in new cars, even those that have run just 4,000 miles, to improve the longevity of the engine by reducing wear and friction.

@@LiquiMolySouthAfrica Great and thanks for the reply. One final question to get clear is , is it safe to add this 300ml of liqui moly to the engine oil which is already filled to the suggested capacity by manufacturer. In my case it is 3.8L filled in hyundai creta petrol egine. If I add 300ml extra does it put any pressure on engine?

@@jaipalreddy4894 When adding Liqui Moly Cera Tec (product code 3721) to your Hyundai Creta's engine oil, it is important to consider the oil capacity. The total capacity of the engine oil should not be exceeded by more than 5-10%. In your case, your engine oil capacity is 3.8 liters. Here are your options: 1. Drain 300ml of Engine Oil: To ensure you don't overfill the engine, you can drain 300ml of the existing engine oil before adding the 300ml of Cera Tec. 2. Slight Overfill Tolerance: Many engines can tolerate a slight overfill of up to 10%. In your case, an additional 300ml would bring the total to 4.1 liters, which is within a reasonable range for most engines. However, this depends on the specific tolerances of your Hyundai Creta's engine. To avoid any risk, it's generally safer to drain the 300ml of existing oil before adding the Cera Tec. This ensures you stay within the manufacturer’s recommended oil capacity. If you need further assistance or have any more questions, feel free to ask!

Thank you for your message. Here’s some information about Liqui Moly DI Jectron and how it can benefit your BMW : Liqui Moly DI Jectron is designed to keep the fuel system clean and maintain engine performance. It helps in removing deposits from injectors, valves, spark plugs, and combustion chambers. This can be particularly beneficial when using ethanol blends like E30. Benefits of DI Jectron: 1. Cleaner Fuel System: Regular use helps keep the injectors clean, which is critical when using ethanol-blended fuels that can leave deposits. 2. Improved Engine Performance: Clean injectors result in better fuel atomization, improving combustion efficiency and engine performance. 3. Corrosion Protection: While DI Jectron primarily cleans the fuel system, it also offers some corrosion protection, which is important when using ethanol blends that can be more corrosive. Regarding Corrosion Protection with E30 Blend:** While DI Jectron provides some level of corrosion protection, if your primary concern is corrosion due to the ethanol blend, you might consider additional products Fuel System Treatment #8365 which provides enhanced protection against corrosion and helps in stabilizing the fuel.

It is called Liqui Moly Visor cleaner code 1571.

Yes you can, the MOS2 is a friction modifier and the motor oil saver rejuvenates the seals and adjust viscosity, if an issue with oil pressure and leaks. What is the result you are looking for, why would you want to add both at the same time...let me know your desired outcome so we can support you best?

No need to add less engine oil, as most people add the additive after a service. The 300ml additive won't overfill.

@@LiquiMolySouthAfrica Thanks a lot 🙏

This video is 1st Race day and then the long one is the final, day 2 Race. Then there is Time trials. All 3 are loaded. Enjoy

That is correct, any cleaning process is difficult when the service is warm. Always best to make sure engine cold and services being cleaned is not in the sun.