Video

Awesome. Very clear!

👍

What turbo is on the white truck?

so the video says can boost leaks cause turbo overspeed. That would've been cool to get that question answered but I'm pretty sure 30 seconds from the end of the video you said a couple words about it and that was all. I'm gonna scour and find more can anybody answer the question will a boost leak. It's a very simple answer. Of course there's a bunch of different circumstances where this may not happen or it may happen worse for others, but is the answer yes, it's just that simple will overspill your turbo. If you have a leak fix it if you have a boost leak your turbo getting damaged.

Not truck related but what if you have a turbo that has a electric actuator that controls the waste gate and the turbo is failing and over boosting would this cause oil to go though the air intake? My car has a ccv which I have replaced and I can see little oil to the turbo from there there which I believe is in the normal range. My turbo actuator makes a buzzing noise and boost is strange I think it's over boosting. My exhaust dpf and air intake throttle is getting covered in a alot of oil and I believe this is cause my diesel car to missfire also. I have a oil leak externally that I believe is under the turbo so be either the turbo or feed/return I'm not sure yet till I dismantle. I don't think I have excessive crank case pressure, I just don't understand why so much oil is going through the turbo as it can only get there from the feed. If it was over boosting as I mention would this do this? Or does this seem like it's a common case of turbo seals failing? My only gripe with oil seals failing is why is it also leaking externally.

Sweet video thank you

Which s300 are these im trying to get one for mine but i dont know which is a good size

Would a badly leaking exhaust flange just before the turbine cause heavy oil leaks on the compressor side? Enough to fill the cooler? Had an IX35 over run on me with a recon turbo fitted. Everything checks out, return, feed, case pressure, case vent, air filter. Only thing I noticed is the exhaust flange of the turbo was leaking where the bolts let go. I assume high RPM with minimal gases going past the turbine not spinning the compressor fast enough to create pressure, would suffer vacuum and suck the oil out? I dunno, it's driving me a bit mad. Never had a turbo fitment go wrong.

Great video. Thanks.

Great! Thank you.

brilliant

are you guys close to coming out with a s366sxe comp r wheel anytime soon?

That is one beautiful truck, and u know we all live for that damn turbo whistle and spool up!

I have 2012 and the 2nd VGT turbo took a dump, so I am going with the 3rd gen swap, I kept getting P2262 and P226C and P040D (That's an EGR code since I don't have it anymore), I reloaded my tune and the P2262 and 226C are not showing up, I may reload he tune to be on the safe side and then again I may just do a plug and play and go from there.

Awesome vid. Answered all my questions and got straight to the interesting points.

Well my turbo is smoked… 😢, thanks for the info

Thanks for the breakdown. If i can scrape the extra couple hundred bucks I'm going with the race wheel.

Is this turbo a holset housing or something different. The 75hp injectors you recommend are they your brand built in house by you. I believe I read you use or sell ducky injectors. I really like the looks of this set up. Especially where you offer upgrades in bearings. I'd appreciate some information. I've been watching all your CZcams videos your very informative. 1999 vp44, Mads electronics s03, banks cold air, flowmaster 4"stainless turbo t tip 70 series mufflers. MDC logo is badass. I'd be grateful for any information.

Thank you for this video!!!!!! My turbo is leaking from hot side. Just fixed my oil drain fitting in the oil and and if it still leaks I’ll do a rebuild. But I did buy a new center cartridge just in case.

great video! Thank you :)

Good information. I wish i knew that before i got my new turbo. I will now put on a new pair of pants

My son is about to do this on his g56 dually

Excellent video very informative 👍

I have a new turbo on my truck, previous turbos were leaking bad. I’m getting oil at the intake plenum area by the grid heater. What are the chances this is from just oil buildup being pushed through the intercooler?

Do the kits y’all have include block off plates?

You probably said it in the video but I have major ADD. Is there a performance upgrade in switching manifolds?

What size turbo is that?

Thank you

how does it compare to a k27?

My 14 is already deleted and I want to pick up this kit. So no retune is required at all?

Anyone happen to have a video of this turbo on a dyno run?

just had a compressor/turbo blow in a diesel car,garage put a camera on the boost side,fins are all damaged,after watching your video i understand now that the shaft is moving side to side hence the damage,not sure if theres a boost leak,watched loads of turbo videos recently but this was clearly explained and not too technical,the garage said it could be crankcase pressure as well,€2,700 euros to replace btw.thanks

This is literally the only video you will need to watch if your turbo has ANY end float, an excellent explanation 👍

I’m just wondering how these swaps do in the cold I have a 08 6.7 and live in Canada where -40 in the winter is pretty common

Great video, I bought a S261sx-e, lasted a month. Im running 600bhp at 2.7bar. Just upgraded the thrust from a 270 to a 360°. See how it goes. If it goes again. It means im pushing the turbo too fast. Will have to get a bigger turbo as i can't live without high boost.

How big is that exhaust?

Finding oil in the hot part is the seal only failed because haven't pleat front and back. How to seal the cold part is used gasket or RTV. I found white stuck stuff but don't know hat is if is a gasket how is called this type. Thank You Sir

how about for dual ball bearing turbo?

What’s the max boost

Commenting for support

Commenting for support

On a early 3g with a 47re that’s stock can I run a s464 on a 2nd gen manifold with a tight housing and be ok? How much horsepower will it make and will it spool well on stock fuel

Does it need any fuel mods to support this turbo or this can be drop in stock truck and go?

Sound very nice

Too much smoke. More air for all that fuel

Straight to the point and very well explained! Seeing the turbo cutaway like that was very helpful in understand how lubrication and bearing work. I always appreciate these educational videos that don't have a bunch of shouting, music and annoying messing around. Thank you!

Yo u recomend s363 or 366 for stock fuel inj and just tuner ?

Good explanation very helpful...i got my surplus turbo....and i saw it on your explanation i thought its not good bcoz it has a play side by side.. According to you its ok....thanks ...

What about when you have your crankcase vented to atmosphere with breather but CcV still intact (recently replaced as well), and you get white smoke until it rises in temperature? Pickup is deleted 6.7, assuming the turbine side oil seal is compromised? VGT seems to function flawlessly, was deleted at 35k and showed up around 60k

Mine is fine I just feel shaft play side to side which is normal but I see scratches on the sides which does not look good