- 17
- 230 685
JHF Engineering
Registrace 25. 08. 2014
How to change starting and stopping point of Main Air Compressor
Changing the pressure range in Differential pressure switch of compressor will also change the starting point and stopping point of compressor. Please the watch the video for more details.
zhlédnutí: 335
Video
Unstable Pressure in Air Reducing Valve of Control Air
zhlédnutí 2,5KPřed 2 lety
Air Reducing Valve for Control air in Engine room
How to insert & fit seal rings of puncture valve's piston
zhlédnutí 1,7KPřed 2 lety
This short video is all about fitting of seal rings in puncture valve of B&W Engine. I hope it helps you.
How to recondition globe valve
zhlédnutí 396Před 2 lety
How to recondition globe valve using lathe machine onboard the ship
Oil leak in Steering gear Auto-pilot
zhlédnutí 1KPřed 2 lety
How to stop leakage of hydraulic oil in Ship's Steering gear Auto-pilot control unit by tightening V-seals using fabricated tools. I hope it helps.
How to set Purifier to Clarifier
zhlédnutí 4,6KPřed 2 lety
This is the procedure of how to set the purifier to clarifier in Mitsubishi Selfjector SJ*GH series with HIDENS system without removing or changing gravity disc and without installing blind disc at the bottom of disc stack.
Pulling-out heavy sprocket of cargo-hold hatch-cover's drive motor
zhlédnutí 413Před 3 lety
Heat up and burn them, all stubborn things and they come-out so softly and easily.
MGPS seachest valve removal
zhlédnutí 1,3KPřed 3 lety
Removal of MGPS seachest valve during laden condition is possible but you have to take shower in Engine room in the right time but not in the right place.
Cutting-off fuel pump of Main Engine B&W MC during EMERGENCY with one cylinder disabled.
zhlédnutí 17KPřed 3 lety
This video is all about cutting off of fuel pump or making it out of work. This scenario is when the fuel pump's plunger and barrel is jammed or the fuel pump is inoperable and the Ship needs to depart with one cylinder of Main Engine disabled.
How to replace/install new bearings of Ship's Cargohold Hatch-cover's Roller.
zhlédnutí 1,6KPřed 3 lety
This short video provides information on how to replace bearings in cargohold hatch-cover's roller during at sea.
REPLACE FUEL FILTER OF TOYOTA HILUX 2015-2020
zhlédnutí 141KPřed 3 lety
This video shows the ways how to replace the fuel filter of Toyota Hilux 2015-2020.
How to replace stuck bearing of ship's crane
zhlédnutí 599Před 3 lety
Easy but effective way of replacing stuck bearing of crane.
Oily Water Separator 15ppm Simulation Test
zhlédnutí 17KPřed 6 lety
Oily Water Separator 15ppm Simulation Test
Salamat sa demo ❤
Hi bro what are the size of your pipe?
Great video, so simple and to the point. Keep up the awesome work 🫶
Boss good day baka pde mag ask sa Manual nito for rtflex thanks
❤❤❤❤
boss sa innova 2016 pataas ano viscosity at liters po.salamant
How many kilometres after again change diesel filter
Thank you! Was able to do it all with no errors :)
Thanks for your video. I followed your instructions, but I now have diesel dripping from the fuel filter holder. Any tips as to where I went wrong?
Thanks for the video sir. I have a problem with my MELO purifier which is working as clarifier, every discharge it has a leaking alarm, what might be the problem of this one sir? Thank you!
Cuantos litros lleva amigo ???
Good job, which hose suction from the fuel tank, small or bigger hose. Thank you
Thanks
طريقة اطفاء لمبة فلتر الديزل لجميع سيارات تويوتا الديزل czcams.com/video/u4feD9gYqd8/video.html فيديو بي اللغه العربي
Very helpful sir 👍
very minute info buddy....good luck 🤞
very detailed information,, although i didn't try onboard thanks 👍
Ayos yan, Lods shortcut method pero Hinde mo na tinanggal yung diesel na laman ng filter cup, dapat tinanggal mo pa rin ung diesel para matanggal lahat ng duming deposits sa filter Cap Pero Solid pa rin sa shortcut method Salamat
Wat about cylinder liner lubrication
And how to do the reset conter of the fuel filter?
Very good commendable job by all engine room crews
great!!!!
im the 700th subscriber, greetings fm malaysia
Thanks
Tnx,,bro,,
Sae 90 gl4
Can you please tell on my ship we have Sj 100gh purifier which is working as purifier ,its recirculation line pressure is high 2.8 bar ,and purifier (small amount of oil) leaking during operation . Can u suggest what is problem
If it is working as purifier, the circulating valve must close and heavy outlet valve is open. And if you have leak in heavy outlet, you might have problem with your interface like incorrect gravity disc.
Very well explained..Thanks sir
at video1:31, "remove the screw and locks".. what is the name of this assembly?
ginagamitan ba talaga yan ng chainblock???
yes. mabigat yan. may spring yan sa loob.
take down to the workshop and do the job !
Yes and then make the same procedure like what in video.
P
Some mechanics remove the fuel filter housing assembly completely and clean the inner housing. Is this really necessary?
Did you get any other system except this one? Something like pneumatic cylinder operated system to lift the roller from cam?
No, I dont have experience such kind of system. Please share it or if you have drawing, kindly share it to us.
So, in order to get the desire starting pressure you need to adjust the differential pressure setting. Stopping press minus desire starting press will get the differential press set. Many thanks
Exactly
really love your videos. please keep posting such videos. 4th engineer here.
remove the fuel pump fuse, start the car a few times to release the pressure from lines so you dont make a mess 😁
👌✅
Cảm ơn rất nhiều . 👌✅
Wow thanks
How do you presurre setting of air reducing valve
To reduce pressure, turn the bolt on the top of reducing valve counter-clockwise. To incease, turn clockwise.
Nice
Very detailed loved it...Please also make a vedio on how to change the discharge time of purifier.
Thanks it was helpful.
Welcome
ung pusher in roller sir specific sa sang cylinder na disable ung pump/barrel etc..?lahat ba ng pump bawat cylindro may ganun..diko napansin kasi......
Every cylinder has an individual shaft for lifting cam.
👍👍👍👍
Thank you for making this video Dear Sir, GOD Bless.
Welcome
Ayus mga birada natin sir ahh..pg sumikat ka sir at kumikita na sa youtube..pahinge ng bleesings..hehehe
Hehe cge
Great video sir..I didn't understand the dowel part
Dowel is the small pin where the sprocket was attached that act as an indicator
@@joseheraldflorese9159 got it sir..pls keep posting these kind of videos
i didnt get anything
R U an Engr?
15 ppm alarm is coming continuously reason and remedy?
Look for manual how to clean the sensor.