Video

Mine is clean inside- still does not work?

Thank you so much!!!!

Thank goodness for people like you on CZcams. I was ready to throw this trimmer to the curb, but thanks to you, it lives to trim another day. Thank you for the very helpful video!!!!

My ST1520 Trimmer had no debris. Line feed does not work.

Thank you! Worked like a charm!

Excellent video, very helpful. The right hand bearing on the upper drive shaft (the one with the friction disc) fell out, and I wasn't sure what the Trunnion Bearing Assembly was, how it worked, and what it connected to. After viewing this video, I understand how the whole thing works, and how to reconnect the Trunnion Bearing and repair the snowblower. Many thanks!

Excellent video, 5 minutes to fix, like new….thank you!

Just what I needed. 5 min job. Easy fix. Thank you!

Thank you! Now to run outside and give this a try!

I followed instructions and this worked for 20-30 minutes then had string on one side so took it out and tried to reload. It didn’t work so took all apart again, no obstruction out back together and won’t load, it clicks like it wants to but it’s not working any second steps?! I would love a response. Thanks!

Thanks for posting this! Super helpful. That nut can be a little recalcitrant so WD-40 will handle the resistance.

how is it easy to install? How many miles do you get?

Has anybody had the issue of it just unwinding while you’re using it? The string winds in just fine, but when I use it, it unwinds.

Perfect video! Fixed mine as soon as I got hone from work I was so excited 😂 kudos!

Thank you!

How do I remove the spool from the lower assembly?

This worked! Thank you.

thank you so much!! i was just about to jetison this weedwhacker into the sun!! 5 minutes later ,and its finally working! thank god it survived getting whipped into the side of the shed last weekend!! god i feel stupid!! lol thanks again!

Thanks. Fixed my problem straight away.

The black piece under the nut on mine spins. Holding the Green part does nothing to facilitate loosening nut. Is that another problem? I've yet to be able to loosen nut by holding the green thing..and I haven't been able to hold the black piece on top well enough to break it loose. Please let me know if I'm missing something? Thank you so much for the video…

That was it thanks. I had fibers from an old tarp wrapped up inside ans it was driving me nuts

You saved my bacon (a whole lot of time, inconvenience and frustration). Thanks for posting!

They dont sell this machine no more

This is excellent guidance for a problem that was driving me mad. Thank you so much. Why doesn't the manual cover this? Hello. Ego?

You saved me so much frustration and neighbors didn’t have to hear my sailor’s mouth. Thank you.

Thanks, I thought I was going to have to buy a new trimmer.

My son built this for me as a Mother’s Day gift… it’s now June 21st and here’s my tomatoes!! 1:38

You saved me a ton of headache! Thank you!

Wow, thank you so much. I was about to give up, but,...... of course there is You Tube. Such a simple and obvious issue, and so easy to fix Thank you again.

if that power does not work at all like fails to let string out when you tap on ground . Stop working all together , Can buy a replacement put a new on the shaft ?

My Ego string trimmer winds sting in just fine. However, when I bump/hit/strike the bottom against a firm surface it does not release the string. I have rewound it three times, same result. I'm thinking I should have purchased a different string trimmer.

My ego trimmer when i press the line power button. The head only spins. It doesn't take up the line.

Heads up. That plastic head isn’t just as simple as pulling it away from the frame after unscrewing all of the screws.

Any videos for replacing the spring?

Life saver! Thanks for the video!!

Just made two of them. Your directions were spot on! Thanks so much

Sorry. That’s Not a radial arm saw. 🤷🏻‍♂️

Worked like a charm! Thanks much!

Great job. Thanks. You made it plain and simple.

I’m very basic when it comes to carpentry. This was a great 2 hour project

I added the 3 blade weed whacker attachment. I hit a ant hill and stopped the blade. The battery pack motor will no longer power the lower unit. Any advise would be greatly appreciated.

Sigh what about the head I took it off to put a crazy idea and am sure I lost parts;)

Mine spins but doesnt load anymoire, dont know what to do to fix it.

Just fixed mine it had a whole ass weave caught in the head. You know I live in the ghetto

I took out all the screws but it wont come apart. I will try again tomorrow.

Made one today using your instructions and it came out awesome couldn’t be happier

👍🏻👍🏻👍🏻👍🏻👍🏻

My husband was ready to buy a new trimmer because the string wouldn't load. I found this video and he had it fixed in 5 minutes. Thank you so much! Your video was clear, concise, and exactly what we needed!

Good video...but I have the opposite problem...my auto feed won't work so the line doesn't come out.

Easy fix...worked liked a charm...Thank you