Video

oh dear..

that was unfortunate especially as it was such a great landing...wonder was the engine idle a little high as it should really have slowed down

Practice slow flight up high.

If this was a kit does it come with the covering pre cut? ... Covering looks great

Alot of those joints came apart because they were not glued in the first place

Good thing is that its totally repairable. Hope to see that Jug back in the air soon!

fire the camera guy

All those layers of paint keep ading weight to that plane!!

Hope you get it repaired ok, what about fitting some electric brakes from the likes of JP Retracts.

I didn't use the stiff metal control rods as there was too much resistance. Too much load on the servos. Check everything I wrote in RC Groups

I have flown mine and it was a handful, nearly lost it. I found out it was nose heavy at the front CG position and adjusted the batteries to balance at the rear CG position. It flew much better. It is also important that the plane of the rear propeller be at 90 degrees to the horizontal stabilizer. Check RC groups for more information.

Maybe it's just the camera but, you seem to fly so far away. This airframe will actually fly very slow final approaches. Warbirds are so slippery. I throttle back on the downwind leg. Keep you're turns mostly flat.

Tell your friend to shut up and let you fly the airplane

Dan that is for air only no paint should be in that area. 2:13

13:22 ..👍🍺🍺🍺...that's exactly like when Ted Striker's squadron attacked at Macho Grande...😅😅😅...

9:21 ...🍺🍺🍺🍺🍺👍

0:12 ..👍🍺🍺🍺🍺🍺😁😁😁

We used to race those at my club. OS 120AX on tuned pipes swinging 14x14 APC pattern props. Radar said 134mph but they seemed a lot faster.

No flaps, high idle, didn’t kill the engine or go around, didn’t pull the tail down to get some drag. You did everything you could to crash it.

Hi Dan. My right aileron servo in one of my planes was doing just the same. After a month I finally crashed the plane when this specific servo finally stop working for good. REPLACE IT!!!!

Too high idle, not enough flaps and wrong propeller. That prop doesn´t brake at all....

Way too high a throttle at idle ! You'll get her fixed sorry about your mishap

I had that on my Hog Bipe with Futaba 3003 servos. Switched to ProModler 130oz servos and it went away

I think your idle was too high. Low end might need to be richer. Sorry to see it get broken. 190's used to be great for scale competition due to great ground handling.

この程度では墜落とは言えません。修復は容易だと思いますがARF機だと外観をどうするかが問題ですね。

You can always go around! Just like us full scale guys, if you’re not on the ground in the first 1/3rd of the runway, go around! Approach speed was quite excessive. If it’s not right, it won’t fix itself.

Throttle has trim on radio, adj when landing to reduce engine speed. Darren

I love the FW190, but it is a tricky bird to land. I flare right before I finally stabilize the approach to land to bleed off as much speed as possible and I still don’t have it fully figured out.

My favorite local event, my club volunteers throughout the year

I would use flaps if it's not windy, turn final at a lower altitude, not dive at the runway, idle the motor down more, and use a prop with less pitch, perhaps a 27x11. I think the 26x13 might be pushing too much air at idle, especially at a fast idle. Flaps will help slow the plane down and also lower the wing's angle of attack which will help prevent tip stalls. With full flaps, the plane might slow down too quickly if you pull the power off completely, so use a little throttle on final and during the round out. Practice slow flight. Climb to a safe altitude, throttle back, lower the flaps, and practice flying around just above the stall speed. See how slow you can fly without stalling.

You are really paying for not knowing how to tune the engine properly, you had the same problem with rhe topflite P-51, , when will you learn, obviously you have deep pockets, Whoever told you a warbird flys like a trainer is either a liar or a fool. You acceptance that this is part of the hobby is part of your problem. When the same problem happens with nitro or gas maybe its you. The jerk who will say I'm harsh are to be avoided. Ive suggested thst you distsnce yourself from their advice or commiseration. You lack someone who is honest, and wishes only for your success.

Landing looked perfect but engine idle speed maybe too high to stop? Maybe cut the engine on rollout if necessary?

Why you didn't use Flaps for landing , also guessing your Throttle idle is to high

Use flaps, and most importantly, lower that idle, its way too high obviously, Or get a prop with less pitch if you cant. And kill the motor on touchdown.

You idle was too hi plus, I have not idea why the genius giving you points did not say kill the engine when you where close to the grass. In my gas planes I got a 3 position switch one is kill the other is Idle low and 3er Hi idle for flying, now I need hi idle do to 3D maneuvers and hover but still the same, so sorry for the bad luck.

Fly downwind lower and maybe reduce idle RPM, good luck with the repair

sorry to see this Dan, it was a great landing, just stopping a heavy model without brakes downhill , rebuild & refly xxxxx

Needs scale prop!!!

So sorry beautiful plane and such a beautiful Landing also broke my heart

Sorry for your mishap. The plane was flying very nicely. I noticed that you were landing your Focke-Wulf on its mains. Focke-Wulfs don't like that. They prefer three-point landings. The P-51s, on the other hand, love to land on their mains. I hope that you can fix it and fly it again soon!... Give that three-point landing a try... That's how I land mine every time... Mine is the Eflite Focke-Wulf 1.5M made out of foam. I don't like balsa for obvious reasons... If you sneeze hard close to the plane, they will break... Foamy planes are sturdier...😁👍🏾 Thumbs-up for your video 👍🏾 Have a great rest of your night 🌙 Greetings from Douglas, Arizona 🌵 👍🏾 😁 🇵🇷 Like#22

Sorry about the crash…don’t be afraid of full flaps for warbird landings

What’s a man without a P-51…keep it

Im sure your "local NTSB" report of yourself and friends already went over what-ifs, but seemed like a high-idle, fast approach, and negative grade runway landing all aided in the outcome. Can only hopefully guess it was into prevailing winds too. Real sorry to watch, hope all the salvageable parts (non-airframe) go into a new build!

That makes my stomach sick when that happens

Beautiful plane. Too bad on the landing crash. Is the idle too high?

You aren't producing much content

Oh my goodness, so sorry for the loss of a nice plane

I was considering getting one of these planes, but now that I have seen the actual size, I am going to look for something smaller. This thing is HUGE! Tom Sisson

I told you that it appeared that it was wrong input, on your part because it hooked into the fence. You should have a plate holding the horn not wood screws but bolts

Lets Go Crash....