Video

I got the movie poster lightbox idea from a channel called “Virtual Robot Revolt”. I stole some of his ideas but constructed them a little differently. I was going to buy them but then I decided to build them myself. The drapery is just stapled at the top and bottom of the wall hidden by trim. I can still get to the window because there’s an opening slit around the window. I just finished up my ticket booth and will be posting a video on the final build. Thanks for the kind words and nice talking to ya!

Thank you!

Thanks!

Thank you! very much appreciated.

Good point. how would you design it in a 8 1/2 wide by 14 1/2 room?

That’s funny, all this time I thought my walls were flat gray.

Thank you!

I bought the Snap Frames from Amazon. There the 27 x 40 SnapeZo brand. Then I built the wooden frame, the exact dimensions of the snap frame itself or a little smaller, depending on the look you want. When I built the frame I finished nailed them together I did not use screws. Had a problem with the wood splitting even though I pre-drilled them. At that point I painted the frame and let dry. Lay the wooden frame on the ground and use a framing square to square the corners. Then set the snap frame itself right on top of the wooden frame with the snap frames open. The snap frame has a groove on the inside where you can screw right through into the wooden frame. Make sure that the snap frame is even on the wooden frame all the way around. Once screwed in the frame becomes sturdy, I didn’t put a backing on the wooden frame I left it open. That’s the way I decided to do it. Other people have a backing, which is up to you. I have my LEDs directly onto the wall on top of silver Christmas wrap paper. Most people use foil tape, but I didn’t want the walls messed up with the adhesive backing. I use the Govee 32.8 foot light strip the cheapest one I could find.

Thank you! It really means a lot!

Dude! It has been a long time. Didn’t see your comment until now. I noticed that you quit making videos for a while now. I didn’t know what happened to you. Glad you’re doing well. I’m glad you like my Theater Room. I have done tons more since this video. Even my latest video I have done a lot more. Picking up a Projector and receiver probably within the week. I’m going with the Epson LS12000 and most likely the Emotiva MR1 Receiver. Glad you stopped by. Hope your family is doing well. Take care of my friend.

Got them at Amazon

They’re made by Art3D. There PVC wall panels. They have different designs also.

I was afraid those sconces would rattle. Thanks. I don’t have my Theater done yet as far as components. But when I clap my hands, I can hear the sconces ring a little.

Unless you're using an emulator, this game was only on the 360..

Both rows will be moved up, but I can’t move them up a couple feet because the riser is not long enough. Meaning that the persons feet would be hanging off the riser. But what I can do is move the seats up probably 6 to 7 inches and get away with it. I think I messed up on the riser and should have made it a little bigger. The theater seats are screwed into the plywood floor. So it would be an effort to move them up regardless of the distance. But that’s what I have planned.

@@Losttouchjs yeah it's a learning experience for all of us! Anyway the priority front row are fine and as far as the rear row goes. Well, they call them the in-law seats for nothing 😁

The room is so small both seats are centered 😂 but I know what you’re talking about.

I’m going to eventually get a digital poster from you. But I think I will save up first. 😂 Looking for two of them. Are those digital posters ready to go out of the box? The frame around them are amazing.

Thank you. There’s a more updated video if you’re interested.

106 Silver Ticket. And the room is 10 x 16.

Thank you so much! 😊

Thanks!

10 x 16 really small but usable.

Thank you so much!

Thank you.

Their Wall Decorator panels made out of PVC. Made for the walls, but I use them for the ceiling.

Just read your equipment list in the thread below.

@@english9646 Thank you so much! The room is 10 x 16. The room in the beginning of the video will also be remodeled into a lobby. It’s going to have the same carpet as the Theatre. The entrance way into the Theater was actually two closets back to back. The original entrance way into the room was in front on the right side by the screen. I wanted the lay out to be where you had to go through the lobby to get to the Theater. I gave up a lot of usable space for this project and sometimes I even question doing it to this day. 😂

Don’t have the Projector yet but I’m looking at the Epson 12000. BasX MR 7.2.4 Emotiva AV Receiver. Speakers are the Polk 265 RT for the surrounds. The fronts will be the Polk 265 LC. Atmos speakers are the Polk VT60. 106 inch Silver Ticket screen. And Kaleidoscape. The seats are commercial theater seating from octane.

@@Losttouchjs Since your theater room is already top notch why not the Sony VPL-XW5000ES? Epson is a major step down 🤷 They are similar priced. The epson has the picture quality of an old 1080p plasma. Once calibration is done on the epson you end up with less lumens than the Sony. If I were you I would watch some videos on the comparison between the two. The contrast and black level on the Sony is twice as good. With such an amazing room it would seem like a downgrade.

@@kman9387 The Sony 5000 was the first on my list. I’ve seen all the CZcams demos and comparisons and I was convince according to the reviews that’s what I was going to get. And then I did a direct comparisons between the Epson and the Sony at a high in home theater store. In my opinion the Epson won out with the black levels and the overall performance. Deep down inside I know the Sony is better, but the Epson is speaking to me more. Plus it’s cheaper. I’m going to consider the Sony one more time before I pull the trigger. Thanks for your feedback and kind words. 😊

@@Losttouchjs Good luck sir 👍🤞🙏

​​@@Losttouchjsthe LS12000 is an excellent projector. That is the projector I am getting. I demoed the 5000es, NP5, and the NZ7. The differences are incremental when considering price vs performance. The black levels weren't that far off. In total black out the JVC won, but with light and contrast the Epson had the edge it also had the edge in motion. I liked all of the projectors, I ultimately ruled out the NP5 due to the cost of bulbs and the NZ7 wasn't $4000 better than the LS12000. I was able to get a killer deal on the LS12000 and went with that one over the 5000es. Good luck on your projector search.

Thank you! A lot of hard work. 😥

It was done with liquid nails and then tacked up with a Brad gun. You have to set the nail gun to the shallowest setting that you have otherwise it will blow through the PVC. If the gun is set to the right level, you can’t even see the nails. When I touch the ceiling it feels solid, which was the first thing I was worried about. Cutting out the holes for the Atmos speakers and lights was a little bit of a nightmare because of the design. but it worked out good. They don’t have any acoustical value whatsoever other than reflection. 😂

The acoustical panels are made by UMIACOUSTICS. I bought them on Amazon. I modified them with the white trim though, and put carpet inside behind the panels to give it extra absorption. The carpet is from Joy Carpets from Lowe’s. The screen is from Silver Ticket 106 inch. The surround speakers are Polk Audio 265 RT. The Atmos speakers are from Polk also. There’s no projector nor are they any components. The theater is brand new and still in construction. I just installed commercial theater seating from Octane. A new video showing the seats will be up today sometime.

Thanks! Yeah I don’t post any more videos. But who knows I might in the future 😊

Um... WTF is seriously wrong with you dude?