Video

On your recommendation, I purchased the Winged Extended Thumbscrew so I could tighten it down using the media mod, and guess what, the screw is too short to reach the other side. I had to modify two of them so I could tighten them down. I carefully took a hacksaw and cut off the little piece on the wing part making the screw just long enough to catch the holding nut. I am also using the GoBUDi Extension Pole Set compatible with All GoPro Hero Cameras. After removing the small piece on the wing nut they work just fine now but I shouldn't have had to do that.

Very well done sir.

I can’t find the caster???

great vid!

Excuse me sir, do you have Santa Fe fog lights ?

Great content 👌 👏

My gopro 10 is overheating since installing mediamod, I've noticed this a few times. Looking for solutions

HIDDEN HARDWARE!!!

A full led reflector bar would have looked better imo

Wow, thanks for the tip. It looks amazing. If you wrenches look like that, I hope there is a shop tour in more recent videos to watch.

So I just added this BOV, but I don’t get boost when revving in neutral like this. How do I do that?

How much were the sliders?

I saw some are install blow off valve near throttle body, is that correct????

What about swapping the bumper directional signal lights up to the taillights where they belong ?

Thanks for the video-great ideas and most helpful.

Hey Stan, thanks for the video. I just bought a used Santa Fe Calligraphy 2022 with NICHE GAMMA 22in rims. I was worried if it makes sense at all to use them or replace with 20in for a more comfort ride. What would you suggest? Thanks in advance

Where did you get the replacement trim?

You did not say where to buy the large wing mount screw for my GoPro 12

ive been thking of wrapping my land cruiser in this color. I've been on a green kick

this may be a bit off a silly question, but would this process be the exact same for any other bov? i bought a greddy bov

Where did you buy the lip , I’m looking for a safe website to buy, for my weds kranze bazreia 18'

Superb plan & wonderful Job! Outstanding organizational skills you have!

what about the other BIG issue.. Media mode makes the gopro no longer waterproof. I think this is worse than the changing screws. Water could ruin the gopro!

How many mm are the sheets you have?

Does it come with a warranty?

I have to let you know that I like your videos but I had to stop watching this one because you kept moving in and out from were you were working and it started to make me sick but I do like your video's sorry

Hey bro what area u from, could use a install buddy 😅

Any thoughts on upgrading the rear turn signal bulbs to brighter ones? Easy to get to...

Thank you! I have had my media mod for a year and have rarely used it because it is such a pain.

hey man! i just installed mine exactly same like this but im not getting any chirp sound like the hks make. do you know how to fix?

You didn't use it.....

gopro needs to make a media mod that allows people to remove the gopro without having to unscrew anything. so dumb that they integrated the folding fingers come out of the media mod. you can't easily slide the GoPro it in and out.

I'm currently renting this car & loving it. I like the assists too except the one that sometimes tells me to take a break, lol

Well done accurate video. Did you contact Fast cap, did they reimburse you in anyway or change their shipping policies?

Pica are the better markers

Define “cut way inside the traced line”. I understand you want the finished product to be tight but clearly you don’t any it too tight that you have to go back and remove additional foam. So are you cutting on the inside of the black line ? A 1/16th, an 1/8th or what ? Thanks again for the video ! Great information. I appreciate learning all the best practices before wasting my time and money making mistakes.

When will will see some Santa Fe videos?

omg, DUDE...THANK YOU!!!

Can you use a 4-inch backing pad?

I use to have a friend that was just like a brother to me. Sadly he passed away a few years back. Anyway he had the same perfectioness blood running in his veins that you do. Just wish he was here to see this video. Once again Thank You for sharing your time and expertise! Looking forward to trying out the tips you have listed and I will bewatching for more of your video's!!!

Just found this video and I have to say the trick with the blue painters tape is ther bomb!! Thanks so much for sharing your time and expertise!

Brilliant idea!!

I like the shadowfoam approach of directly cutting the outline with a scalpel. Worked pretty well for me so far. Just lightly cut around to mark the outline, then go over again to get to the required depth.

This is amazing. I watched your video and tried to rough cut it and it looked terrible, so I followed your instructions and it came out really professionally done. I think also the tip on using a pick really helps for removing foam. Thank you for doing this video, everything you said worked wonders

I like the black vinyl, but you covered the rear fog lights with it.

Awesome video, that really helped me up my game. Love the layout examples.

Where can I find the replacement drawer slides I can’t find them on harbor freights website

Looks like someone stepped on a hotwheels car, never understood why people like that look

안녕하세요! 한국에서 Genesis coupe를 타고 있는 Myoung Seung Eui 입니다. just call 'M' 한국에서 제네시스쿠페는 오래된 차이기 때문에 제네시스쿠페(shots name gen coup korean word = 젠쿱) 컨텐츠가 많이 없어서 우연히 당신의 영상을 보게 되었습니다. 많은 어려움이 있는것을 알았습니다. 저 또한 차를 유지하는데 많은 비용이 들고 많은 시간과 노력이 드는 것을 알고 있어요! 하지만 저에게는 그 만큼의 가치가 있는 차라고 생각합니다. 아무래도 한국의 현대에서 만든 KDM 차량이니 한국에서 부품이나 여러 정보가 더 많을 것입니다! 제가 도와줄수 있는 부분이 있다면 도움이 돼길 바래 봅니다. 인스타그램은 하지 않아요. 다른 방법으로 연락 할 수 있는 수단이 있다면 연락하면 좋겠네요😊

Hey Stan, with the goquick 2 and long tripod, with the media mod, do you just need to buy the buckle mount adapter that you have listed?????