Video

depends on your RF mode (Eco or Pro). Eco can work for longer time. Pro is more signal strength and shroter working time. Working time per charge is about 2-5hours.

we didn't test the kit with 12V for efoil before. Usually customers use 24-48V.

Hi, speed also depens on your battery, board shape, mast/wing shape, load, etc.

it depends on detailed address and order weight. would you send your detialed shipping address to email eileen@maytech.cn? so I can check and udpate by email for you.

@@EileenMaytech Taiwan, Taichung...

@@brucehuang8515 will you need waterpump for cooling motor and ESC? you can check this link and fill your address and check total cost: michobby.com/products/maytech-electric-surfboard-jet-ski-kits-120116-200kv-motor-500a-waterproof-watercooled-esc-1905wf-remote?variant=44187298758817

for our standard firmware versions: MTSKR2005WF doesn't have cruise control; MTSKR1905WF esurf mode has cruise control by long press brake trigger for about 3s

Maytech waterproof 6374 motor is already waterproof motor :)

Could you email eileen@maytech.cn? so I can check for you

in the video, it's wired throttle. We also have wireless remote controller

Can u recommend? I open a shop in Singapore, and in Singapore we cannot have throttle so we are looking for hidden throttle like urs. We need it for ebike and if u can provide all the tool N information I wish to get more product from u and promoting it in my shop

could you send your requests to my email eileen@maytech.cn? @@mrcoco3562

you're welcome!

and this is another video to show how to display current/temperature, etc datas with this motor and ESC on our 1905wf remote: czcams.com/video/XP-rrRS2ceA/video.htmlsi=xil_73QsP1OlsvjV

would you send your setup details (motor/ESC/battery voltage) to my email eileen@maytech.cn? So I can check and give recommendations.

yes, it's brushless waterproof motor

Yes they are... until they aren't. You're basically thinking of FPV drone motors, and most any brushless motor will not be harmed initially by getting wet. The wires in the brushless motor are coated with a thin enamel so electrical shorts don't happen in the motor windings, and that's good enough to hold back water too, but with enough gunk getting into the motor from not being fully sealed, the protective wire enamel can deteriorate until it's weak enough to short out the motor windings. With a motor that's actually built to be waterproof, there are seals that prevent water and dust from getting to there motor windings at all, leading to a much longer life for the motor in harsh conditions.

@@Chris-oj7ro ahh i guess thats a plausable explanation also your motor is in the water all the time so it makes much more sense to think about waterproofing than on a fpv drone motor where you kinda want to stay away from water anyway :D

85165 inrunner motor aliexpress.ru/item/1005001994277381.html

Could you email eileen@maytech.cn? so I can check for you.

or you can visit our website: maytech.cn/collections/efoil-esurf-rc-boat-parts

we have a pool to test our motors loaded: czcams.com/video/n8Hl3Kq-qcM/video.html

hola, que control remoto compraste, MTSKR1905WF o MTSKR2005WF? para que pueda enviarle las instrucciones de cableado adecuadas

Mtskr1905wf , lo comptre para una tabla de surf que yo construyó , gracias

@@davidcid2011 it also depends on what ESC you're using. could you send your ESC details to my email eileen@maytech.cn? so I can check and send wiring diagram by email to you

no, you can set the delay time of duty cycle accelerate and brake

We have many different sizes waterproof watercooled motors, could you send your detailed requests to eileen@maytech.cn ? so I can check and recommend suitable motor to you.

🤣

🤗let's start saving money from today

200KV

because this thumb throttle only has one direction throttle trigger. If you use our wireless remote, it can go forward and reverse without button

Yes, it's ok to with a wired foot pedal throttle or twist/thumb throttle if use our 300A ESC. if you have need, please email me eileen@maytech.cn, and i will send pictures to you for checking.

Hi, we're manufacturer. for more details, please kindly email me at eileen@maytech.cn. thanks.