Video

This gave my asus 3060 much more stability- I still need to test a few more things out... but, so far following these specs im seeing a dramatic improvement- Thank you.

I came here from the previous video. Over there you tested with the AMD cooler, here you have tested with an AIO. The test bench has been changed.

My ICUE Link H100 LCD Corsair Pump doesnt show in HWiN but I know its running. Does anyone else have this issue where there cooler pump doesnt display in the sensors? I even check the box "show all fans (including stopped or not present)" and it still doesnt show it.

ok it is time to replace my used thermal pad.

Thank you. This is literally the same test I was about to do. I had a feeling it wouldn't be too significant of a difference. It's nice to see someone else on the same page.

Im very new to this so I understand very little. I used this benchmark on the family desktop and row 1 was 161mb and row 2 was 183mb. I thought that row 1 is the theorietical best and the second row is what it will reasonably do. Its worth noting the desktop uses a hdd

Buy Asus, get Asus quality. I have an Asus TUF 3080 TI that was randomly crashing. I eventually realized that the Hot Spot would go to 103c+. I repasted the card and now the hot spot max temps is barely 70-75c. There was barely no thermal paste on the GPU. Typical ASUS quality control.

He even future-proofed the video

johny sins doing a pc guide ? lol

I'm subscibing, Just because you gave the answer IMMEDIATELY. Truly amazing.

It’s cold better fire up some cities skylines 2

I can’t even open the thermal paste needle I don’t know how 💀

Astronaut, doctor, plumber, pc builder, is there anything he cant do?

i was a pea dot man, now im a pea+ sized X shape man.

I really love tutorial like this, going straight to the point, fast and clear, thank a lot!

You immediately give me the answer I immediately hit the Like button

U talk to much, Show more

Meistens Verteilt sich die Kühlpaste von selbst sehr gut,durch die Hitze.

my pc turned off help im calling skibidi negros

How to unsee the faces now? Great vid mate!

why would anyone leave the pc on??? with ssd's it takes like 30 seconds to boot.

I have often heard that excess thermal paste can lead to adhesion between the CPU and cooler with possible socket pin damage upon forced removal (turning the computer back to heat the paste is then recommended). I suspect the problem here is that the excess squeezed out paste tends to dry out and harden. It's unfortunate that this area is hard to see and clean.

Would you use them on a play station or Xbox?

doesnt really make sense in the end if you calculate all the cost of thermal pads and the time wasted , instead just go for a kraken g12 gpu bracket and a AIO cooler on it and it will be way cooler or just go for a liquid cooler bracket

ROLF... basics of thermodynamic is saying... Hello. When you add another layer of 'something' .. ALWAYS thermoconductivy will be WORST. Because heat coming between two layers, have some 'obstacles' to overcome. This is 'why' when you do thermoisolation of you house, You doing this by put around 3 layers. In EU we use often bricks, then styro, then final render. Often in countries when is colder.. we put 2 layers of bricks, but with little space between them. And main role of thermopaste or thermopads are, to fill air gaps between CPU and Cooler.

110C ? planned obsolescence? copper shim mod works -15C on memory

I fucking wish you would stop with the jokes.

"bit taunting" => "bit daunting"

Use battery products rather then direct power products Like laptop instead of computer.

I know this has been said many times before, but thank you so much for putting the answer right at the beginning. Knowing the answer early on, it made me curious how you came to your conclusion, so I ended up watch the entire rest of the video (which is really well-put together, might I add). If you had the answer at the end, I likely would have just skipped right to it, and would have been much less informed while not giving your content the watch-time it deserves. Dropped a sub, looking forward to any future videos!

So here's a follow-up question to this. I'm starting my new build shortly and I'll be using 3 m.2s (2x2TB 990 Pro in raid 0, 1x1TB 990 Pro) and I have some Thermalright 0.5mm thermal pads, as well as some 1mm to cut and replace the stock stuff from my mobo. Since the controller sits a tad higher than the NAND on each drive I'll be using, would you still recommend to only cover the controller, or is it worth trying to lightly cover the NAND with the thinner pads? ROG X670e-Extreme with included heat sink plates. TIA!

My gpu is grilling my cpu almost hitting 100C under load.

Dont take i9 or any intel , go for amd to save even more upto 50-70%

I recently changed a laptops thernal paste did everything correctly and with care, changed heatsink, cpu and gpu socket thermal paste, connected every wire perfectly, no smell of burns, no smoke, no boom sound after finished I turned it on it worked but after like 60 seconds when it was booted up the screen went black and pc turned itself off and doesn't turn on now, does anyone know what have might happened? I thought it was power button wires but re atached it and everything seems normal as it was

ur laptop is dope

Me over here with a read speed of 56 mbs ans 112 write

what do you mean on the controller?

Yeah, but I have fans on the bottom - montech 95 pro and 7900 xtx red devil... The only optionnseems to be the case mounted support bracket.

I wanna see this test done with NASA level work load

Power (and thermal) cycling is what will usually kill electronics. I pretty much never power my PC off (since c. 2012, now on the 3rd build), never had a _single_ hardware failure in that time, not even an HDD. The one from 2012 (P8Z77 / 2500K, later 3770K), according to the SMART data on a couple of WD Greens running in RAID 0, was running for 6.5 years of 7.5 years before I upgraded. It drew c. 45W at the wall, the current one under 40W.

Need more videos that just get right to the answers for those who aren't interested in the why. Well done.

The pattern doesn't matter its a matter of pressure , I use either X a □ or about 9 small dots all work fine

I have tried several different methods and the one that works the best is to make sure you get some between the heatsink and the CPU. I just squeeze out a fat pea sized blob in the center and mount the heatsink. I intentionally add what I think is a little too much. I've got lots of 91% alcohol and paper towels if I accidentally make a mess. I used to fuss over stuff like this and actually since socket A it really hasn't mattered.

Its definetly more than Aesthetic

yea, but what about hot spot?

AIO is not a type of cooler, it only means "All in One" :D

Thank you , for the video.

I just have the same issues. its double clicking on middle and the left too

I do a grid of very small dots on all the surface

This video could have been 30 seconds